Instruction/ maintenance manual of the product TH146-N-U Aube Technologies
Go to page of 12
TH146-N-U 1/12 TH146-N-U Installation Guide Non-programmable H/C Controller The TH146-N-U electronic controller can be used with any of the fol- lowing heating/ cooling systems: The following devices .
TH146-N-U 2/12 Choose a location abo ut 1.5 m (5 ft) above the floor on an inside wall. Loosen the captive screw under the console. Detach the console from its base by pulling the bottom section. Secure the base usin g the wall anchors and screws.
TH146-N-U 3/12 With automa tic heating/cooling mode changeover , the re’s no need to adjust the controller at e very change of season or weather condi- tion. The controller switches automatically betwe en heating mode and cooling mode to mai ntain th e desired temperature.
TH146-N-U 4/12 Wiring T ables Heat Pump Te r m i n a l Device 1H1C 2H1C 3H1C 2H2C 3H2C 4H2C 3H3C TH Console Connect the console between the TH termin als (no polarity) TH PS Plenum sensor Connect the .
TH146-N-U 5/12 Wiring Diagram: 2H1C Heat Pump — New Installation AC146-410 AC144-03 CT241 Humidifier Dehumidifier Compressor Auxiliary Heat Reversing V alve Fan Fault Defrost Dual Energy.
TH146-N-U 6/12 Wiring Diagram: 3H2C Heat Pump — Add-on Installation AC146-410 AC144-03 CT241 Fa ult Defrost Reversing V alve Compressor 1 Compressor 2 Furnace Fan Limit Humidifier Dehumidifier Dual .
TH146-N-U 7/12 Wiring Diagram: 3H2C HVAC AC146-410 AC144-03 CT241 Cooling Unit 1 Cooling Unit 2 Heating Unit 1 Heating Unit 2 Fan Heating Unit 3 Humidifier Dehumidifier.
TH146-N-U 8/12 Configuration Menu Item HP HV AC Parameters Display Options Defau lt Description 1 T emperature format °C / °F °C Select the temperat ure display format. 2* Balance point low -30 to 10°C (-22 to 50°F) -10°C (14°F) Set the bP L limit (see section 4.
TH146-N-U User ’s Guide Non-programmable H/C Controller TH146-N-U 9/12 Press the Mode button to place the system in one of the following modes: Press the button to select the fan op erating mode. • In automatic mode, t he fan runs only when heating or cooling is activated.
TH146-N-U 10/1 2 Manual Setting In manual setting, the user sets the humidity level (5 to 60%). 1) Press the Mode button for 3 seco nds. 2) Press the buttons to set the humid ity level. 3) Press the button to exit. The symbol is displayed when the humidifier is On.
TH146-N-U 1 1/12.
TH146-N-U 12/1 2 Printed in USA 09/201 1.
An important point after buying a device Aube Technologies TH146-N-U (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Aube Technologies TH146-N-U yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Aube Technologies TH146-N-U - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Aube Technologies TH146-N-U you will learn all the available features of the product, as well as information on its operation. The information that you get Aube Technologies TH146-N-U will certainly help you make a decision on the purchase.
If you already are a holder of Aube Technologies TH146-N-U, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Aube Technologies TH146-N-U.
However, one of the most important roles played by the user manual is to help in solving problems with Aube Technologies TH146-N-U. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Aube Technologies TH146-N-U along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
