Instruction/ maintenance manual of the product FN620L Poulan
Go to page of 24
• Assembly • Operation • Maintenance • Service and Adjustments • Storage • Troubleshooting • Repair Parts OWNER'S MANUAL 189783 Re v .
2 • Ne v er operate the tiller without proper guards, plates , or other saf ety protective de vices in place. • K eep children and pets a wa y . • Do not ov erload the machine capacity by attempting to till too deep at too f ast a rate . • Ne v er operate the machine at high speeds on slippery surf aces.
3 CONGRA TULA TIONS on your purchase of a new tiller . It has been designed, en gi neered and manu f ac tured to giv e you the best pos sible de penda bil ity and per fo r m ance. Should you e xperience any prob lems y ou can not easily remedy , please contact your nearest authorized service center .
4 ASSEMBL Y OPERA T OR’S POSITION (See Fig. 1) When right or left hand is mentioned in this manual, it means when you are in the oper ating position (standing behind tiller handles). Y our new tiller has been assembled at the f actory with exception of those parts left unassembled f or shipping pur poses.
5 ASSEMBL Y han dle s _ 96 TILLER HANDLES CABLE HANDLE P ANEL BOL TS 02051 FIG. 2 HAN DLE P ANEL HEX BOL T 5/16-18X3/4" TILLER HANDLE HEX BOL T 5/16-18X1" FLA T W ASHER LOCK W ASH ER NUT depth_stake_5 DEPTH ST AKE SUPPORT BOL T HEX BOL TS, LOCK W ASH ERS, AND HEX NUTS DEPTH ST AKE SUPPORT NUT “A” ENGINE BRA CK ET HAL VES FIG.
6 KNO W Y OUR TILLER READ THIS O WNER'S MANU AL AND SAFETY R ULES BEFORE OPERA TING Y OUR TILLER. Compare the illustrations with y our tiller to f amiliarize yourself with the location of v arious controls and adjustments. Sav e this manual f or future ref erence.
7 OPERA TION The operation of any tiller can result in f oreign objects thr own into the e yes, whic h can result in severe e ye damage. Alwa ys wear safety glasses or e ye shields bef ore starting y our tiller and while tilling. W e recommend a wide vision safety mask o ver spectac les or standard saf ety glasses.
8 OPERA TION FIG. 7 engine_a rt_ 4 OIL FILLER PLUG OIL LEVEL T O ST AR T ENGINE (See Fig. 8) CA UTION: Keep drive control bar in “DISENGA GED” position when star t- ing en gine.
9 OPERA TION • Y ou will fi nd tilling much easier if you lea ve a ro w un- tilled between passes . Then go bac k between tilled rows . (See Fig. 9) There are two reasons for doing this. First, wide tur ns are much easier to negotiate than about-f aces.
10 GENERAL RECOMMEND A TIONS The warranty on this tiller does not co v er items that hav e been subjected to operator ab use or negligence. T o receive full value from the w arranty , operator m ust main tain tiller as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your tiller .
11 MAINTENANCE FIG. 12 AIR CLEANER (See Fig. 13) Ser vice air cleaner car tr idge e v er y twenty-fi ve hours, more often if engine is used in very dusty conditions. • Loosen air cleaner screws , one on each side of cov er . • Remo ve air cleaner co v er .
12 MUFFLER Do not operate tiller without muffl er . Do not tamper with e xhaust system. Damaged muffl ers or spark arresters could create a fi re hazard. Inspect pe ri odi cally and re place if nec es sar y . If y our engine is equipped with a spark arrester screen assembly , re move e v ery 50 hours for cleaning and inspection.
13 TILLER T O ADJUST HANDLE HEIGHT (See Fig. 15) F actory assembly has provided lo west handle height. Se lect handle height best suited f or your tilling conditions . Handle height will be diff erent when tiller digs into soil. • If a higher handle height is desired, loosen the four nuts securing handle panel to engine brack ets .
14 SER VICE AND ADJUSTMENTS TINE OPERA TION CHECK (See Fig. 21) Be sure tines do not rotate when engine is running and tine control is in the “OFF” position. W ARNING: Disconnect spark plug wire from spark plug to pre vent starting while chec king tine operation.
15 SER VICE AND ADJUSTMENTS V -BEL T IDLER PUL LEY TRANS MIS SION PUL LEY BEL T GUIDE ENGINE PULLEY BEL T GUIDE T O REPLA CE V -BEL T (See Fig. 23) Replace V -belt if it has stretched considerably or if it has crac ks or fra y ed edges. Belt guard must be remo ved to service belt.
16 ST ORA GE ENGINE OIL Drain oil (with engine warm) and replace with clean oil. (See “ENGINE” in the Maintenance section of this man ual). CYLINDER(S) • Remo ve spark plug. • P our 1 ounce (29 ml) of oil through spark plug hole into cylinder .
17 Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “T O ST AR T ENGINE” in the Operation section. 3. Engine fl ooded. 3. Wait se v eral minutes bef ore attempting to start. 4. Dir ty air cleaner. 4. Clean or replace air cleaner car tridge.
18 REP AIR P ARTS TILLER - - MODEL NUMBER FN620L HANDLE ASSEMBL Y 1 2 3 15 19 23 5 5 6 4 7 8 9 12 18 34 28 3 16 14 13 11 10 handle_assy_99_26 1 137176X505 Brac ket, Handle 2 72140512 Bolt, Carr iage 5/16-18 unc x 1-1¦2 3 9266R Gr ip , Handle 4 151473 Handle, L.
19 REP AIR P ARTS TILLER - - MODEL NUMBER FN620L BEL T GU ARD AND PULLEY ASSEMBL Y belt_guard_9 3 8 6 7 12 14 13 9 7 7 10 1 2 16 5 17 18 19 20 21 25 4 KEY P ART NO .
20 REP AIR P ARTS TILLER - - MODEL NUMBER FN620L WHEEL AND DEPTH ST AKE ASSEMBL Y 22 7 8 13 9 10 23 22 15 3 24 5 4 7 4 5 17 16 18 18 21 17 16 2 2 1 3 4 5 19 19 20 20 wheel_d.
21 KEY P ART NO . NO . DESCRIPTION 1 165774 Tine, Outer , R.H. 2 4921H Retainer , Spring 3 165772 Tine, Inner , R.H. 4 165771 Tine, Inner , L.H. 5 165773 Tine, Outer , L.
22 REP AIR P ARTS TILLER - - MODEL NUMBER FN620L TRANSMISSION KEY P ART NO . NO . DESCRIPTION 18 10040400 W asher , Loc k 1/4 19 74610412 Bolt, Hex 1/4-28 x 3/4 Gr . 5 20 - - - - - - - Engine, Briggs Model 94202 (Order par ts from engine Manuf ac- turer) 2 3 5 6 8 11 16 17 11 10 7 19 14 10 12 18 10 14 1 20 transmission_12 KEY P ART NO .
23 KEY P ART NO . NO . DESCRIPTION 1 132629 Decal, Logo 2 163989 Decal, Logo 4 127185X Decal, Description 5 110613X Decal, Tine Control 6 110614X Decal, Hand Placement 8 120076X Decal, W arning, Rotat.
LIMITED W ARRANTY The Manuf acturer w arrants to the original consumer purchaser that this product as manuf actured is free from de- f ects in materials and work man ship .
An important point after buying a device Poulan FN620L (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Poulan FN620L yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Poulan FN620L - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Poulan FN620L you will learn all the available features of the product, as well as information on its operation. The information that you get Poulan FN620L will certainly help you make a decision on the purchase.
If you already are a holder of Poulan FN620L, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Poulan FN620L.
However, one of the most important roles played by the user manual is to help in solving problems with Poulan FN620L. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Poulan FN620L along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
