Instruction/ maintenance manual of the product pp-7000U-III POSIFLEX Business Machines
Go to page of 7
Part 1 Aura Series (PP - 7000 - III / PP - 7000 U - III) THERMAL PRINTER TECHNICAL INFORMATION A. INTERFACES 1. Peripheral interface The connector for peripheral control is a 6P6C RJ11 jack with the following pin assignment. The best recommended cash drawers to this connector are Posiflex CR3100, CR3200, CR4000 and CR4100.
Part 2 PIN # Definition Descr iption 1 FG Frame ground 2 CRB Drawer kick for cash drawer controlled by software command Esc p 0 n1 n2 3 SENSE Input peripheral status 4 VCC + 24 V DC supply 5 CRA Drawer kick for cash drawer controlled by software command Esc p 1 n1 n2 6 SG Signal ground B.
Part 3 Effect of posit ions 1 & 2 on baud rate is defined as in table below with parity check set according to position 3, number of data bits always set to 8, and stop bit set to 1. When the parallel interface is used, please set both positions to ON.
Part 4 Switch Position 1 2 3 4 5 6 7 8 Serial interface w/ auto cutter OFF OFF OFF OFF OFF OFF OFF OFF Parallel interface w/ auto cutter ON ON OFF OFF OFF OFF OFF OFF C. INTER NAL SWITCH There is an extra internal 4 position DIP switch in PP - 7000 - III series for more technical settings.
Part 5 description of the supported commands if required. 1. Paper out alarm W hen Paper End signal is detected, the printer keeps on intensive beeping and stops receiving data till the signal is neutralized . When Paper Near End signal is detected, the printe r gives a beep every 3 seconds and stops receiving data .
Part 6 bell onto say a kitchen wall, connect the cable from the bell to the peripheral connector on the printer. Then use this command with m set to 0 and both n1 and n2 set to 255. The printer will be able to drive the kitchen bell for about half a second on each such command.
Part 7 Page 19 (PC858: Euro Doll ar Sign included in PC850 for European / Greek model) Page 253 (Greek437 as Default setting for Greek model) Page 255 (Thai for Standard model) Page 255 (Greek for Eur.
An important point after buying a device POSIFLEX Business Machines pp-7000U-III (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought POSIFLEX Business Machines pp-7000U-III yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data POSIFLEX Business Machines pp-7000U-III - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, POSIFLEX Business Machines pp-7000U-III you will learn all the available features of the product, as well as information on its operation. The information that you get POSIFLEX Business Machines pp-7000U-III will certainly help you make a decision on the purchase.
If you already are a holder of POSIFLEX Business Machines pp-7000U-III, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime POSIFLEX Business Machines pp-7000U-III.
However, one of the most important roles played by the user manual is to help in solving problems with POSIFLEX Business Machines pp-7000U-III. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device POSIFLEX Business Machines pp-7000U-III along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
