

IMPORTANT Digital Light Processing, DLP, Digital Micromirror Device and DMD are all trademarks of Texas Instru- ments. Windows 98, Windows 95, and Windows 3.1 are registered trademarks in the United States and other countries of Microsoft Corporation. IBM is a registered trademark of International Business Machines Corporation. Macintosh and MAC are trademarks of Apple Computer Inc. Other names of companies and products mentioned are trademarks and registered trade-marks of the respective companies. TM , ® and © marks are not used in this document.

Precautions Please read this manual carefully before using your PLUS V-1080 / V-807 Data Projector and keep the manual handy for future reference.
This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside of this unit.
This symbol alerts the user that important literature concerning the opera- tion and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.
The above cautions are given on the bottom of the product.
WARNING The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specified by PLUS Technologies in this manual. Failure to comply with this government regulation could void your right to operate this equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide rea- sonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio fre- quency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.


Fire and Shock Precautions
Carrying around When carrying the unit around, please use the carrying case that comes with it and, to protect the lens from scratches, always shut the sliding lens cap. Also, do not subject the unit to strong mechanical shock.

Book-sized, lightweight (at about 0.9 kg/2.0 lbs) and small high-inten- sity mobile projector DMDTM and the synergistic effects of our own optical design serve to improve the optical utilization efficiency. The three light sources (RGB) required in color expression are reproduced with one DMDTM. These factors have enabled a design that offers both high intensity and small size/lightweight fea- tures.
Sharp, clear picture The absence of RGB color infidelity and the inconspicuous gaps between the individual dots permit the display of small characters and diagrams with distinct clarity. An up-close look reveals the differ- ence even more.
Beautiful reproduction of high-quality images from DVD Faithful reproduction of color tones gives rise to the display of natural images. High-quality images such as those from DVD and other sources bring out the display capabilities that are an essential strength of the digital projector.
Heightened effectiveness with picture in picture The video image is projected as a sub-picture within the personal computer picture. This expands the usefulness of the projector even more.
Digital technology corrects the horizontal and vertical keystone dis- tortion of the projected picture New technology is used to correct the horizontal keystone distortion in addition to the regular key- stone correction. This permits even simpler setup adjustments.
Connection permitted for personal computers equipped with DVI con- nectors Inclusion of a DVI connector allows the input of analog RGB signals as well as digital RGB signals. (The supplied conversion cable supports personal computers having a regular analog RGB connec- tor. See the Table of Supported Frequencies on Page 69 for information about display resolution.)


Remove the main unit and the accessories from the box and check that the following items are included.
Remote control (includes one button battery) [1] This controls the projector. Please remove the transportation insulation sheet at time of purchase. (See Page E-13.)
Power cable (1.8 m / 5.9 feet) [1] This power cable supplies power to the unit. See Page E-24 about connections.


DVI / Mini D-sub 15-pin conversion cable (19 cm / 0.6 feet) [1] This is used when the monitor connector of the personal com- puter is a mini D-sub 15-pin connector. See Page E-19, 22 about connections. No. 772708000
RGB signal cable (Mini D-sub 15-pin, 2 m / 6.6 feet) [1] This is used when the monitor connector of the personal com- puter is a mini D-sub 15-pin connector. See Pages E-19 about connections. No. 772709000


S-Video cable (3.5 mm diameter plug / Mini DIN 4-pin plug, 1.5 m / 4.9 feet) [1] This cable is used in the connection of video equipment that has an S-video connector. Connections are described on Page E-21. No. 772705000
Video cable (3.5 mm diameter plug / RCA pin plug, 1.5 m / 4.9 feet) [1] This cable is used in the connection of video equipment that has an RCA jack type video connector. Connections are de- scribed on Page E-21. No. 772704000

Audio cable (2.5 mm diameter plug / RCA pin plug, 1.5 m / 4.9 feet) [1] This cable is used with equipment that has phono type audio jacks. Connections are described on Page E-23. No. 772706000
Soft pouch (for projector and accessories) [1] This pouch is used when storing or moving the projector. The pouch is made up of two portions that are joined by hook-and- loop tape to form a single item. The pouch can be separated into two pieces.

User's Manual (CD-ROM edition) [1] User's Manual (Simplified Edition) [1]


Precautions * Leave the power cable plugged in (for 5 to 10 minutes) until the projector returns to room temperature before placing the projector inside the soft pouch. Placing the projector into the pouch soon after switching off the power could cause the projector to break down. * Be sure to attach the lens cap and place the projector into the soft pouch with the lens facing upward.
Accessories · Projector


Front adjuster button [E-27] (There is also one on the left side.)
Lens cap To protect the lens, attach the lens cap when the projector is not in use.
Precautions The ventilation slots discharge the heat of the lamp and care must be taken not to come into contact with them.


Built-in Security Slot This security slot supports the MicroSaver Security System manufactured by Kensington Microware Inc.



PIP button [E-31] (Displays the picture associated with the VIDEO connector as a smaller picture within the display screen associated with the PC connector)
FREEZE button [E-31] (Freezes moving pictures)
MUTE button [E-31] (Temporarily cancels the video and audio)
Buttons used for input selec- tion [E-28] DIGITAL button, RGB button, YPbPr button, VIDEO button, S- VIDEO button, and YCbCr but- ton AUTO button [E-29] (Automatic adjustment of the analog RGB moving image)
QUICK button [E-32] (Displays a simplified menu)
ASPECT button [E-30] (Selects the vertical and hori- zontal ratio of the screen)
Buttons used for menu opera- tions [E-37]
HKSTN button [E-34] (Horizontal keystone distortion correction display)
VKSTN button [E-34] (Vertical keystone distortion cor- rection display)
ZOOM button [E-35] (Digital zoom adjustment display)
VOL button [E-36] (Volume adjustment display)
+/– button (Used in all adjustments)
Precautions Handling of the Remote Control * Do not drop the remote control or handle it inappropriately. * Do not expose the remote control to water or other liquids. Should the remote control become wet, wipe it dry immediately. * Try to avoid use in hot and/or humid locations. * Please keep button batteries out of the reach of children. If a battery is swallowed, promptly obtain the medical care of a doctor. * Remove the batteries from the remote control when it is not going to be used for a long period. * Some operations (such as menu operations) are available only through the use of the remote control and attention should be given to its careful handling.
POWER button [E-24]

Using the remote control for the first time The battery compartment is fitted with a transportation insulation sheet at the time of shipping. Pull out the sheet and remove it. The remote control is now ready for use.
Replacement Method 1 Insert the tip of a ballpoint pen or some other pointed object into the hole of the battery holder, then pull out to open.
2 Remove the old battery and install a new button battery with (+) side facing upward in the battery holder.
Purchase a CR2025 type battery for replacement.
H
P
A
N
M
O
O
T
S
J
A
CR2025
3 Insert the battery holder into the remote control and push in until the battery holder closes with a "click" sound.
N
A
CR2025 M
CR2025
T
S
J
A
P
O
O
n · n

Remote Control Range
Point the infrared transmitter of the remote control toward the remote control sensor located at the front or rear of the main unit and operate. Reception of the remote control signal should generally be possible within the range illustrated below.
Remote control infrared transmitter
4m / 13.1 feet
7m / 23 feet
4m / 13.1 feet
7m / 23 feet
Remote control infrared transmitter Top View


Height from center of lens to top edge of the projection
4.0(13.1)
3.5(11.5)
3.0(9.8)
2.5(8.1)
2.0(6.6)
1.5(4.9)
1.0(3.3)
0.5(1.6)
17.2˚ Projection angle
0.5 (1.6)
1.0 (3.3)
1.5 (4.9)
2.0 (6.6)
2.5 (8.1)
3.0 (9.8)
3.5 (11.5)
4.0 (13.1)
4.5 (14.8)
5.0 (16.4)
5.5 (18.0)
6.0 (19.7)
6.5 (21.3)
7.0 (23.0)
Center of lens Projection Distance
Height from center of lens to bottom edge of the projection
Screen Size Designation (Inches)
Screen Size Width x Height Projection Distance Height h1 Height h2
(m) (feet) (m) (feet) (m) (feet)
0.710.53 0.810.61 1.220.91 1.631.22 2.021.52 2.441.83 3.052.29 3.662.74 4.063.05
2.10 2.40 3.58 4.79 5.97 7.19 8.99 10.79 11.98
0.36 0.39 0.59 0.79 0.98 1.18 1.48 1.77 1.97
35" 40" 60" 80" 100" 120" 150" 180" 200"
2.331.74 2.662.00 4.002.99 5.354.00 6.634.99 8.006.00 10.007.51 12.008.99 13.3210.00
1.20 1.37 2.06 2.75 3.43 4.12 5.15 6.18 6.87
3.94 4.49 6.76 9.02 11.25 13.52 16.90 20.28 22.54
0.64 0.73 1.09 1.46 1.82 2.19 2.74 3.29 3.65
0.11 0.12 0.18 0.24 0.30 0.36 0.45 0.54 0.60
* There is a tolerance of ±5% due to design values. * This table uses the lens apex and lens center as references and requires that the projec- tor be in a horizontal condition (with front and rear adjusters fully withdrawn).

V-1080 Screen Size and Projection Distance
Height from center of lens to top edge of the projection
4.0(13.1)
3.5(11.5)
3.0(9.8)
2.5(8.1)
2.0(6.6)
1.5(4.9)
1.0(3.3)
0.5(1.6)
17.2˚ Projection angle
0.5 (1.6)
1.0 (3.3)
1.5 (4.9)
2.0 (6.6)
2.5 (8.1)
3.0 (9.8)
3.5 (11.5)
4.0 (13.1)
4.5 (14.8)
5.0 (16.4)
5.5 (18.0)
6.0 (19.7)
6.5 (21.3)
7.0 (23.0)
Center of lens Projection Distance
Height from center of lens to bottom edge of the projection
Screen Size Designation (Inches)
Screen Size Width x Height Projection Distance Height h1 Height h2
(m) (feet) (m) (feet) (m) (feet)
0.740.55 0.810.61 1.220.91 1.631.22 2.021.52 2.441.83 3.052.29 3.662.74 4.063.05
2.13 2.36 3.51 4.69 5.87 7.02 8.79 10.53 11.71
0.33 0.36 0.52 0.69 0.85 1.02 1.28 1.54 1.71
36" 40" 60" 80" 100" 120" 150" 180" 200"
2.431.80 2.662.00 4.002.99 5.354.00 6.634.99 8.006.00 10.007.51 12.008.99 13.3210.00
1.20 1.32 1.99 2.65 3.31 3.97 4.97 5.96 6.62
3.94 4.33 6.53 8.69 10.86 13.02 16.31 19.55 21.72
0.65 0.72 1.07 1.43 1.79 2.14 2.68 3.21 3.57
0.10 0.11 0.16 0.21 0.26 0.31 0.39 0.47 0.52
* There is a tolerance of ±5% due to design values. * This table uses the lens apex and lens center as references and requires that the projec- tor be in a horizontal condition (with front and rear adjusters fully withdrawn).

Please check the following matters before making connections to the personal computer. * Suitable resolution for V-807 is 800 x 600 dots (S-VGA), and the displayable resolution is XGA (1024 x 768 dots). * Suitable resolution for V-1080 is 1024 x 768 dots (XGA), and the displayable resolution is S-XGA (1280 x 1024 dots). Note that input of a resolution that exceeds the displayable resolution will cease to be projected and should this be the case, you will need to change the resolution to a displayable resolution at the computer side. Check with "Table of Supported Frequencies" on Page E-70. * The setting method of the personal computer will differ depending on the personal computer that you are using. For information, read the instruction manual for your personal computer, read the on-line help, or contact the manufacturer of your personal computer.
Personal Computers with a DVI Connector * Make the connection with a DVI-D cable and the PC connector of the projector. When connecting, arrange the connectors in the proper orientation and plug in. Turn the screw knobs and fasten to the connector of the main unit. * Switch the input selection of the projector to "Digital RGB".

DVI-D cable (Available as an option. Order code: 28-697)
Monitor output

Personal Computers with a Mini D-Sub 15-Pin Connector * Make the connection to the projector's PC connector and the mini D-sub 15-pin connector through the use of a DVI/mini D-sub 15-pin conversion cable. * When connecting, arrange the connectors in the proper orientation and plug in. Turn the screw knobs and fasten to the connector of the main unit. * Switch the input selection of the projector to "Analog RGB".


Note * Before making connections, check the power of the projector and the equipment to be connected is switched off. * When projection will be with a notebook computer connected, knowledge will be required for the cable connec- tion and notebook computer startup procedure as well as the operation that follows startup. Please consult the instruction manual of your notebook computer or the on-line help.
Personal computer

To Output the External Output Signal of a Notebook Computer When projection will be with a notebook computer connected, knowledge will be required for the cable connection and notebook computer startup procedure as well as the operation that follows notebook startup. Please consult the instruction manual of your notebook computer or the on-line help while per- forming the following procedure.
1 Check whether a signal is being sent from the notebook computer to the projector. An indication appearing on the liquid crystal display of the notebook computer does not necessarily mean that an external output signal is being output. 2 Should a sign not be output from the notebook computer, please try the operation described below. For an IBM PC/AT, DOS/V computer, press the [Fn] key plus any one of the [F1] to [F12] keys. (See the table below.)
Manufacturer Model Key akia All computers Fn + F2 COMPAQ ARMADA Series Fn + F4 PRESARIO Series Fn + F3 DELL All computers Fn + F8 FUJITSU All computers Fn + F10 GATEWAY All computers Fn + F3 IBM All computers Fn + F7 NEC All computers Fn + F3 Panasonic All computers Fn + F3 SHARP All computers Fn + F5 SONY All computers Fn + F7 SOTEC All computers Fn + F3 TOSHIBA All computers Fn + F5
Note When the liquid crystal display of the notebook computer and the projector are displayed at the same time, the projected image might not be correct even though the liquid crystal display shows a correct indication. Should this occur, stop the simultaneous display of the notebook computer and try the mode with external output only. (Try an operation such as that described in aforementioned Step 2 and try closing the liquid crystal panel which might result in external output only.)

Connections with Video Connectors
Video Equipment with VIDEO Connectors * Make the connection to the VIDEO connector of the projector using a video cable. * Switch the input selection of the projector to "Video".
Video Equipment with S-VIDEO Connectors * Make the connection to the VIDEO connector of the projector using an S-video cable. * Switch the input selection of the projector to "S-Video".
Video deck, DVD player, document camera, etc.

Video cable (Supplied item)

Connections with Component Signals
When the Video Connectors are Y, Cb, and Cr Connectors * Make the connection to the projector's VIDEO connector using a component signal cable. * Switch the input selection of the projector to "YCbCr".
When the Video Connectors are Y, Pb, and Pr Connectors * Connect a DVI/mini D-sub 15-pin conversion cable to the PC connector of the projector, then make a further connection using a component cable (which is available as an option). * Switch the input selection of the projector to "YPbPr".

Component cable (Available as an option) (3.5 mm diameter, 4 Pde, Plug to RCA3) (Order code: 28-698)
Component cable (Available as an option) (D-sub 15-pin to RCA3) (Order code: 28-690)

Connections with Audio Connectors
* Make the connection to the projector's AUDIO jack using an audio cable. * The built-in speaker of the projector provides monaural audio. * To enjoy convincing audio reproduction, please connect the audio output of the video equipment to your audio system.
Video equipment, personal computer

Audio cable (Supplied item)

There is an order in which the power cable is connected and the power is switched on/off.
Operating 1 Connect the AC IN connector of the projector and the power outlet using the sup- plied power cable. The POWER indicator will light amber, the cooling fan will rotate at low speed, and the unit will enter the standby mode.

2 Switch on the projector power Main unit operation: Press and hold the POWER button for a while. Remote control operation: Press the POWER ON button.
ON OFF POWER STATUS POWER STATUS POWER STATUS POWER
Flashes green (Approximately 60
Lit green Power is on
The POWER indicator changes to a flashing green and lights steadily after about 60 seconds. The projection screen brightens after about 40 seconds.
The projector is now capable of regular projection.
seconds)

Finishing 1 Switch off the power of the connected equipment 2 Switch off the power of the projector Main unit operation: Press and hold the POWER button for a while. Remote control operation: Press the POWER OFF button.

The "Power Off" indication will appear. When the red bar extends fully (in about 5 sec- onds), the projection screen will go off and the unit will enter the power off operation.

The POWER indicator changes to flashing am- ber and lights a steady amber after about 60 sec- onds (when the unit enters the standby mode).
POWER
3 Unplug the power cable Check that the POWER indicator is lit in amber and then unplug the power cable. The POWER indicator will go off when the power cable is unplugged.

Warrning Under normal circumstances, please do not unplug the power cable unless the POWER indicator is lit in amber. Doing so may shorten the life of the lamp or result in breakdown of the projector.
Do not unplug the power cable while the POWER indicator is flashing amber. Doing so may shorten the life of the lamp or damage the projector.

Switch on the power of the connected equipment and make the adjustments with the video signal being input to the projector.
Adjust the projection image to the screen. Check that the screen is set level and vertically. (1) If the image is shifted to the left or right, move the main unit horizontally. (Align the center of the
screen and the center of the lens of the main unit.) (2) If the image is shifted vertically, move the image up or down with the adjuster. See "Making Adjust-
ments with the Adjusters" on Page E-27. (3) If the image is slanted, adjust by turning the right or left front adjuster. See "Making Adjustments with
the Adjusters" on Page E-27. (4) A projection image such as that illustrated in the diagram is the result of the projector not being
perpendicular to the screen. Set the projector so that it is pointing straight toward the screen. (5) If the image shows keystone distortion, adjust using remote control or menu operations. See "Cor-
recting Keystone Distortion of the Projection Image" on Page E-34.




Making Adjustments with the Adjusters
Care must be taken not to come into contact with the ventilation slots which discharge the heat of the lamp.
Raising the projection image While viewing the projection im- age, press hand hold the front ad- juster buttons located at the left and right (1) and, raise the projec- tor to align the image with the screen, then release your fingers (2). Turn the left and right front adjust- ers for fine adjustment. Adjust so that there is no shaking of the projector.
QUICK
POWER SOURCE
MENU STATUS
POWER
(1)
(2)
(1)
Lowering the projection image Lower the front adjusters using the operation described above. Raise the rear adjuster. Turn the left and right front adjusters to make fine adjustments. Adjust so that there is no shaking of the projector.
POWER
POWER SOURCE
QUICK MENU
AUTO
PC AUDIO VIDEO
Focus Adjustment
Turn the focus ring to the right or left and adjust the focus. Should the size of the projection image extend be- yond the screen or be smaller than the screen, move the projector forward or backward and readjust the focus.
Rear adjuster

This section describes the use of direct operation with the main unit or remote control buttons. For information about operation using the menu, see "Menu Operation Method" on Page E-37 and the various items on Pages E-46 to E-60.
This operation selects the input signal to be projected.
Main unit operation: Press the SOURCE button. (It will not function while the menu or the quick menu is displayed.)
When Auto Source is On If there is no input signal at the source that was previously used, the projector automatically selects another source that has the next input signal.
QUICK
When Auto Source is Off Each press of the button switches the selection one step in the sequence of Analog RGB → YPbPr → Digital RGB → VIDEO → S-VIDEO → YCbCr.

Remote control operation: Press the desired input se- lection button.
When Auto Source is On When an input signal is not present at the selected source, the projector automatically selects the next source that has an input signal.
When Auto Source is Off The projector switches to the selected source regardless of whether an input signal is present.


Automatic Adjustment of Analog RGB
This function automatically adjusts the position shift of the analog RGB input signal, the size of the picture, vertical striping, and color infidelity.
Normally, this function is adjusted automatically at the time of sig- nal selection.
Main unit operation/Remote control operation: Press the AUTO button. (This will not function while the menu or the quick menu is displayed.) A press of the AUTO button starts the automatic adjustment.


Note * If the display position is shifted, vertical lines appear on the picture, or the projection is not good even after using automatic adjustment, please perform image adjustment manually. See "Picture Adj. / Fine Picture / H Position / V Position " on Page E-47. * When the image extends beyond the boundaries of the screen or is smaller than the screen, set Aspect to "Auto". See "Selection of Aspect Ratio" on Page E-30 and "Aspect" on Page E-51.

Selection of Aspect Ratio
This function selects horizontal and vertical picture propor- tions of the input signal.
Press the ASPECT button while viewing the projected image and select the aspect ratio.
Personal Computer Image (when selecting digital RGB or analog RGB) Each press of the ASPECT button advances the selection one step in the sequence of Auto → Direct → Real, and then repeats.
ASPECT AUTO
Auto Automatically enlarges or reduces the image to project a
full screen in a ratio of 4:3 Direct Maintains the aspect ratio and projects a picture of the maxi-
mum displayable size Real Projects the input signal without pixel conversion
Image of the Video Equipment (when selecting VIDEO, S-VIDEO, YCbCr, or YPbPr) Each press of the ASPECT button advances the selection one step in the sequence of Auto → Wide → Zoom, and then repeats.
Auto While maintaining the aspect ratio, projects a full screen so
that no portions extend beyond the boundaries of the screen. The top and bottom of the 16:9 image becomes black. Wide Projects to fill the full width with the entire image at 16:9. Zoom Projects only the 4:3 portion within 16:9 image to fill the
screen.
DIGITAL RGB YPbPr · VIDEO S-VIDEO YCbCr

Projecting a Sub-Picture
This function displays the video image (i.e., the picture of the VIDEO connector input) on the personal computer screen (i.e., the PC connector input screen) as a sub-picture.
Each press of the PIP button advances the screen size of the sub-picture one step in the sequence of Small → Medium → Large → Off (i.e., the sub-picture display is off), and then re- peats.
Note * The sub-picture cannot be displayed when the main screen receives the image from the VIDEO connector. * The sub-picture cannot be displayed when picture in picture is set to off. The size of the sub-picture can be selected. See "Using the Quick Menu" on Page 32 and "Picture in Picture" on Page E-54. * To change the display position of the sub-picture, see "Picture in Picture" on Page E-54. * The main picture is termed the Analog RGB, Digital RGB, or YPbPr input screen, whereas the sub-picture is termed the VIDEO, S-VIDEO, and YCbCr input screen.
POWER
FREEZE MUTE PIP
QUICK ASPECT AUTO
Freezing a Moving Picture
This function is used to stop and view a moving picture. Note that the input image continues to advance even though the picture there is a still picture condition.
POWER
FREEZE MUTE PIP
A press of the FREEZE button changes the screen to a still picture. A further press returns the screen to a moving pic- ture.
Cancelling Video and Audio Temporarily
This function is used to cancel the video and audio at the same time.
POWER
Press the MUTE button to cancel the video and the audio. A further press brings a return to the original condition.

Using the Quick Menu
This function permits frequently used adjustments to be performed quickly. Note that the Quick Menu will not be displayed unless the signal of the connected equipment is input. Please select the input that you wish to adjust.

Main unit operation (1) A press of the QUICK MENU button brings up the quick ad-
justment display. Further presses allow selection of the de- sired adjustment display. (2) Press the or button to make the adjustment. (3) To close the display immediately, press the MENU button.
In the absence of operations for a period of about 10 sec- onds, the display will close automatically.
Remote control operation (1) A press of the QUICK MENU button brings up the quick ad-
justment display. Further presses cause the adjustment dis- play to change in sequence. The adjustment display can be selected with use of either the cursor ▲ or ▼ button. (2) Press the cursor or button to make the adjustment. (3) To close the display immediately, press the CANCEL button.
In the absence of operations for a period of about 10 sec- onds, the display will close automatically.
(2)

Content of Adjustments and Settings
+ – Brightness 0
Brightness Adjusts the brightness of the image. Brightness decreases in the (-) direction and increases in the (+) direction.
Contrast Adjusts the contrast of the image. Contrast becomes less distinct in the (-) direction and more pronounced in the (+) direction.
V Keystone Corrects (vertical) keystone distortion of the screen. Adjusts the left and right edges of the screen so that they are parallel.
H Keystone Corrects (horizontal) keystone distortion of the screen. Adjusts the up and down edges of the screen so that they are parallel.
Picture in Picture The picture from the VIDEO jack is displayed as a sub-picture on the input screen from the PC connector. This function selects either the size of the sub-picture (i.e., large, medium, or small) or off (i.e., no display). (Neither the adjustment display nor the picture will be output unless the signal is input to the PC connector.) See Page E-54 for information about changing the display position of the sub-picture.
Volume This function adjusts the volume of the built-in speaker. The volume decreases in the (-) direction and increases in the (+) direction.
Display Item Adjustment/Setting


This adjustment is used when the projection screen is dis- torted. Note that extreme distortion cannot be corrected and in such cir- cumstances the projector should be placed to face the screen straight on beforehand.
the HKSTN button. The horizontal keystone adjustment dis- play will appear.
To adjust left-right distortion (e.g., Screen Example 2), press the VKSTN button. The vertical keystone adjustment display will appear.
(2) While viewing the screen, press the (+) button or the (-) but-
ton and adjust the vertical or horizontal edges to be parallel. In Screen Example 3, horizontal and vertical keystone distor- tion should be adjusted.
(3) To close the display immediately, press the CANCEL button.
In the absence of operations for a period of about 10 sec- onds, the display will close automatically.
Note * The keystone adjustment values can be overwritten and saved. See "Keystone" on Page E-53. * Overcompensation of the horizontal keystone correction value will result in a narrowing of the vertical keystone adjustment range. Likewise, overcompensation of the vertical keystone correction value results in a narrowed horizontal adjustment range. * Note that the adjustment range will differ depending on the adjustment conditions. * The screen examples have been depicted in an exaggerated form to aid in description.
Screen Example 3

Enlargement of the Image and Video Movement
This function digitally enlarges the personal computer image and video image (up to 10 times).

Each press of the (+) button enlarges the image and each press of the (-) button makes the image smaller (returning it to 1:1).
(3) Pressing the cursor (▲▼ ) buttons at the time of the zoom
operation will cause the display position to move. (There will not be any movement when zoom is at 0.)
(4) To close the display immediately, press the CANCEL button.
In the absence of operations for a period of about 10 sec- onds, the display will close automatically.
The image can also be moved in the following circumstances. * When "Aspect" is set to "Real" by the signal of the personal computer, and the input resolution is higher than the display resolution of the projector. * When "Aspect" is set to "Zoom" by the video signal.

Note * Zoom and image movement functions are cancelled when the input is switched. * The greater the zoom enlargement, the less distinct the image will appear. The reason for this is that the dots are being digitally corrected so that they are not conspicuous. * Movement of the screen will not be possible when the menu screen is being displayed.
(4) (3)

Adjustment of the Volume
This function adjusts the volume of the built-in speaker.

(1) Press the VOL button.
The volume adjustment display will appear.
+ – Volume 53
(2) Adjust the volume.
The (+) button increases the volume and the (-) button de- creases the volume.
(3) To close the display immediately, press the CANCEL button.
In the absence of operations for a period of about 10 sec- onds, the display will close automatically.
(3)

Names and Functions of the Remote Control Buttons that Operate Via a Menu
MENU button Used for menu display and menu closure.

Cursor (▲▼ ) buttons Used in the selection of menu names and item names as well as in setting and adjusting the item contents.
CANCEL button Used to return to menu name selection as well as to close the menu (and the sub menu display).
ENTER button Used to set the verification display.

Names and Functions of the Main Unit Buttons Used in Menu Operation
MENU button Used to display menus, to return to menu name selections, and to close menus (i.e., closing sub menu displays).

(AUTO) button Advances the selection of menu names. Advances the setting/ adjustment values of the item contents. Also serves the function of the remote control ENTER button.
(QUICK MENU) button Used in the selection of item names.
(SOURCE) button Returns to the selection of menu names. Advances the setting/ adjustment values of the item contents.
Menu Names These are the menu titles. When a menu is selected, the display changes to the title screen. The selected menu name appears in red.
Cursor (dark blue) The setting/adjustment of the cursor position can be performed.

Item Name The name of the ad- justment/setting
Adjustment bar setting contents Adjustment bar: Indicates the adjustment condition by increases or decreases in bar length Setting contents: Displays the set contents
Sub Menu

Performing Menu Operations
Preparation Switch on the power of the connected equipment, start the play operation or an- other operation, and input the signal to the projector. Select the input that you wish to adjust. The menu display of the description diagram depicts an example in which the "H Key- stone" item name is selected.

The menu name that existed when the menu was closed previously will be displayed.

Selection of the Menu Name
2 Press the cursor ( ) button to select the menu name


Each press of the cursor () button advances the selection one step in the sequence of "Color" → "View" → "Setup" → "Info." → "Image". Each press of the cursor () button causes a return of one step. The selected menu name will appear in red.

This condition allows selection of the item name.
Red


4 Press the cursor (▲▼) button to align the cursor with the item name
Main unit operation: Press the (QUICK MENU) button. When the cursor has moved to the very bottom of the items, another press will move it to the very top of the items.
Press the cursor () button since the "Key- stone" example of the description diagram displays the icon. The sub menu will be displayed. Press the cursor (▼) button and align the cur- sor with the desired item name. When the icon is displayed and depend- ing on the item contents, a press of the cur- sor () button will result in the setting display, a resetting of the adjustment value, or a re- setting verification display. Please see the vari- ous item descriptions.

5 Press the cursor ( ) button and make the adjustment (or setting) while viewing the image When a button is pressed, the image will also change.


Adjustment display: Each press of the button results in a change of 1 point and continued presses cause changes to proceed in order. Setting display: The setting contents display changes with each press of the button.

Closing the Menu
6 Press the MENU button and close the menu display

Main unit operation: Press the MENU button and cancel the cursor display. When a sub menu is displayed, press the MENU button to close the sub menu, then press again to cancel the cursor. This condition allows the menu name to be selected.

QUICK

A press of the MENU button while the cursor is not displayed will close the menu display.
Cursor

Selecting Another Menu Name with Remote Control Operation

When a sub menu is displayed, press the CAN- CEL button and close the sub menu. Press the CANCEL button again and cancel the cursor display.


Press the cursor ( ) button and select the menu name. (Selection of the menu name is not pos- sible while the cursor is displayed.)



List of Item Names Offering Input Selection and Adjustments/Settings
The item names that can be adjusted/set will differ depending on the input signal.
[Example of Menu Display Items at the Time of Input Signal Video Selection]
Info. Setup View Color Image
– + 0 – + 0
Menu Name Item Name Sub Menu Item
Brightness Contrast Picture Adj. Fine Picture H Position V Position Color Tint Sharpness Reset Gamma Color Temp. Color System Color Space Aspect Filter Projection
E-46 E-46 E-47 E-46 E-46 E-46 E-48 E-49 E-49 E-50 E-50 E-51 E-52 E-52 E-52 E-53 E-53 E-54 E-54 E-54
Vertical Flip Horizontal Flip V Keystone H Keystone Keystone Save Size Position
"Tint" can be adjusted only at the time of NTSC composite/S signal input.

[Example of Menu Display Items at the Time of Input Signal Video Selection]
Info. Setup View Color Image
Menu Name Item Name Sub Menu Item
Language Auto Source Auto Power Off On Screen Menu Position YPbPr Background White Balance Status Factory Default Lamp Timer Reset Resolution Frequency Lamp Timer
E-55 E-55 E-56 E-56 E-57 E-57 E-57 E-58 E-59 E-59 E-59 E-60 E-60 E-60
Info.

Picture qualities such as brightness and contrast will change depending on the whether the room is bright or dark. Please adjust to suit your preference.
Select the desired item name and then adjust with the cursor ( ) buttons.
Item Name Brightness Contrast Color Tint Sharpness
Cursor () Button Cursor () Button
Darker Less contrast Less dense color More red Softer image
Brighter More contrast Denser color More green Sharper image

Picture Adj. / Fine Picture / H Position / V Position
These adjustments are available when analog RGB signals are input. Usually, automatic adjustment is performed at the time of sig- nal selection, but when automatic adjustment is not effec- tive, these adjustments can be performed.


Picture Adj. (Picture Adjustment) Adjust this when bright and dark vertical bands appear on the screen.
Select the "Picture Adj." item name and adjust with the cursor ( ) buttons so that the vertical bands disappear and bright- ness becomes uniform across the screen.
Fine Picture Adjust this when the picture shows a lack of color fidelity or flickering.

Select the "Fine Picture" item name and adjust with the cur- sor ( ) buttons so that the lack of color fidelity or the flicker- ing disappears.

H Position Adjust this when the picture is shifted to the left or right.
Select the "H Position" item name and adjust with the cursor ( ) buttons.
V Position Adjust this when the picture is shifted up or down.
Select the "V Position" item name and adjust with the cursor ( ) buttons.
This function resets (i.e., returns to the standard settings) the adjustment/setting value of the "Image" menu name.
A press of the cursor () button forces the reset.

Gamma corrects the proportion of change of the dark por- tions from the bright portions of the input signal. Set this to reproduce natural color tone or to distinctly project a personal computer picture in a bright conference room.
Select the "Gamma" item name and select the setting contents with the cursor ( ) buttons.
Color Temp.
Normal Correction with standard settings Natural Corrects for natural color tones Real Corrects with emphasis on brightness
Color Temp.
The screen color is affected by the color of the illumination and other extraneous light. This function adjusts the white, which is the reference color for video equipment, and improves the quality of color repro- duction. Adjustment can also be used to enhance skin col- ors.
Select the item name "Color Temp." and select the setting con- tents with the cursor ( ) buttons.
Color Temp.
Low Produces warm whites (reddish) Medium Produces warm whites (yellowish) Normal Produces the white of sunlight High Produces cool whites (bluish)

Color System
This function sets the color system of the video signal. Normally, this should be set to Auto. Set this function when the system cannot be identified with Auto.
Select item name "Color System" and select the setting contents with the cursor ( ) buttons.
Color Temp.
Auto Automatic identification NTSC Fixes the setting to NTSC PAL Fixes the setting to PAL SECAM Fixes the setting to SECAM
Set this function when a component signal (YCbCr or YPbPr) is projected and the image is extremely red or extremely green.
Select the item name "Color Space" and use the cursor ( ) buttons to select a color space setting that provides a normal im- age.
Color Temp.
Selection contents at the time of YCbCr input YCbCr601, YCbCr709, YCbCrSMPT
Normal Color Temp.
Selection contents at the time of YPbPr input YPbPr601, YPbPr709, YPbPrSMPT

This function sets the horizontal and vertical picture propor- tions of the input signal.
Select the item name "ASPECT" and select the setting contents with the cursor ( ) buttons.
Personal Computer Signal Auto Automatically enlarges or reduces the image to project a full screen in a ratio of 4:3 Direct Maintains the aspect ratio and projects a picture of the maximum displayable size Real Projects the input signal without pixel conversion
Input Signal Auto Direct Real
The setting is higher than the display reso- lution of the projector.
The setting is lower than the display reso- lution of the projector.
Video Signals Auto While maintaining the aspect ratio, projects a full screen so that no portions extend beyond the bound-
aries of the screen. The top and bottom of the 16:9 image becomes black. Wide Projects to fill the full width with the entire image at 16:9.
(This feature is used to project a squeezed image in a proper aspect ratio.) Zoom Projects only the 4:3 portion within 16:9 image to fill the screen.
(Portion that extend off screen is cut.)
Aspect ratio selection Auto Wide Zoom
4:3 screen
16:9 screen

Filter
This function sets the sharpness when the input signal is adjusted to the resolution of the projector and enlarged or reduced.
Select the item name "Filter" and select the setting contents with the cursor ( ) buttons.
Smaller numerical values result in a sharper picture and larger values result in a softer picture. Please select your desired setting value.
This function selects the projection orientation to the screen. It is set when the projector projects to the front or the rear of the screen.
"Vertical Flip" Off "Horizontal Flip" Off
"Vertical Flip" Off "Horizontal Flip" On
"Vertical Flip" On "Horizontal Flip" On
"Vertical Flip" On "Horizontal Flip" Off

Keystone
This function corrects the keystone distortion of the pro- jected picture on the screen. Adjust so that the edges are parallel in the vertical and the horizontal directions.


Vertical keystone (-) direction
Vertical keystone (+) direction
Pressing the button corrects the projected picture in the direction of the dotted screen outline.
Horizontal keystone (-) direction
Horizontal keystone (+) direction


Keystone Save This function is used to save the keystone adjustment values. Setting Keystone Save to on will set the previous keystone adjustment values when projecting after the power cable has been disconnected and then reconnected.
Off The keystone adjustment values return to the initial values when the power cable is unplugged. On The keystone adjustment values are retained in storage even when the power cable has been unplugged.
This function displays the picture from the VIDEO jack as a sub-picture on the input screen (i.e., the main picture) from the PC connector.
Picture in Picture Size
Display at upper left of main screen Display at upper right of main screen Display at center of main screen Display at lower left of main screen Display at lower right of main screen

This function sets the language that is displayed on screen in the messages and menu displays.
The Auto Source function automatically detects the input sig- nal when the power supply is switched on and when the in- put is switched.
Select the item name "Auto Source" and select the setting con- tents with the cursor ( ) buttons.
On Switches on the automatic detection function Off Switches off the automatic detection function
Order of Signal Detection The search is repeated in the order of Analog RGB → YPbPr → Digital RGB → Video → S-Video → YCbCr. When a signal is detected, the search is stopped and the image is projected.

Auto Power Off
This function switches off the projector power automatically when the input of the projector enters a no-signal condition.
Select item name "Auto Power Off" and select the setting con- tents with the cursor ( ) buttons.
On The power is switched off when there is no signal. Off The power is not switch off even when there is no signal.
Operation when Function is On * The "No Signal Power Off" display appears when a no-signal condition continues for approximately 10 seconds. The power is switched off about 5 minutes after this. * If a signal is input during the appearance of the display and an operation button other than the POWER button is pressed, the display is closed and the function is cancelled.
No Signal Power Off
This function switches on or off messages that are displayed in a black frame.
Select item name "On Screen" and select the setting contents with the cursor ( ) buttons.
On The message is displayed. Off The message is not displayed.
Example of a display when the ASPECT button is pressed

Menu Position
This function sets the display position of the menu.
Select item name "Menu Position" and select the setting contents with the cursor ( ) buttons.
Displays on the left side Displays on the right side
This setting causes the projector not to accept component YPbPr signals.
Select item name "YPbPr" and select the setting contents with the cursor ( ) buttons.
Disable Function is made invalid and input selection is not permit-
ted Enable Function is made valid and input selection is made possible.
This function sets the screen color when the input source is no-signal.
Select item name "Background" and select the setting contents with the cursor ( ) buttons.
Black Sets a black screen when there is no signal Blue Sets a blue screen when there is no signal

White Balance
This function automatically adjusts the black level and the white level of the analog RGB input signal so that they suit the personal computer. This serves to improve color repro- ducibility.
Input Black Signal Adjusting Black
White Balance Complete Input White Signal Adjusting White
"White Balance Complete" is displayed for a while and the ad- justment is completed.

Info.
This displays information about the equipment.
Select item name "Status" and press the cursor () button.
Display Contents: Projector model, firmware version, and the internet home page address of PLUS Vision Corp.
Version:1,0,0,0.0
This function returns the adjustments and settings of all the input sources to the standard factory default values.
Select item name "Factory Default" and press the cursor () but- ton.
The display "Press "ENTER" to set Factory Default" will appear.
Press "ENTER" to Factory Default Set
A press of the ENTER button sets the factory defaults. Main unit operation: Press the (AUTO) button.
Items that are not set to the factory default: Projection method, YPbPr, Language, and Lamp Timer
This function resets the lamp timer. Be sure to perform the reset operation when the lamp cartridge has been replaced.
Select item name "Lamp Timer Reset" and press the cursor () button.
The display "Press "ENTER" to reset lamp timer." appears.
A press of the ENTER button resets the timer Main unit operation: Press the (AUTO) button.
Press "ENTER" to Lamp Timer Reset

Info.
This function displays the resolution and frequency of the detected input signal.
This information will not be displayed unless an analog RGB or digital RGB signal is input and an Analog RGB or Digital RGB input selection is made.
1024768 Resolution
This function displays the lamp timer.
When the lamp timer exceeds 1,000 hours, "Replace the Lamp Cartridge." is displayed on the screen for 10 seconds at one minute intervals. Replace the lamp with a new one. See "Replacing the lamp cartridge" on Page E-66 for information about lamp cartridge replacement.
When 1,100 is exceeded, "Warning!! System Shutdown" is dis- play for 10 seconds and the power is switched off.

POWER indicator When the STATUS indicator of the main unit operation panel is lit or flashes, notification is being given of the irregularities de- scribed.
POWER
POWER SOURCE
QUICK MENU
AUTO
AUDIO VIDEO
STATUS Indicator POWER Indicator Action to Take
The temperature has become abnormally high. * The thermal protector is activated. if the room tem- perature is high, move the projector to a cool lo- cation. If the internal temperature of the projector is high, check the ventilation holes of the cooling fan and clean them if they are obstructed. * When the thermal protector is activated, the power is switched off and even if the power is soon switched back on, the power might not actually be supplied to the projector. Should this happen, wait one minute and then switch the power on again.
POWER
Flashes red (0.5 s lit / 0.5 s off)
The lamp will not light up. Wait one minute or longer while the lamp lighting volt- age irregularity detection protector is activated and switch the power on again. If the problem still per- sists, unplug the power cable and contact your dealer.
Flashes red (1 s lit / 1 s off) When the lamp burns out during operation: Flashes amber for 60 seconds and then is lit amber When the lamp does not light from the beginning: Lit amber
The fan is stopped. Unplug the power cable and request service from your dealer.
POWER
Flashes red (0.5 s lit / 0.5 s off)
The lamp cover is open. The lamp cover is not attached properly. Attach it properly.
Flashes red (1 s lit / 1 s off)

STATUS Indicator POWER Indicator Action to Take
POWER
It is timer to replace the lamp. The lamp timer has exceeded 1,000 hours. Replace the lamp cartridge.
When power is on:
Lit green When power is off:
The lamp's service life has ended. The lamp timer has exceeded 1,100 hours. The lamp will not light. Replace the lamp cartridge.
Lit red Lit amber after 60 seconds
of flashing in amber
Thermal Protector When the internal temperature of the projector becomes abnormally high, the STATUS indicator will flash red (at a rate of once per second) and the POWER indicator will light red. The thermal protector is activated and the power of the projector is switched off simultaneously. Should this occur, proceed with the following actions.
Lit red · Lit amber

Check the following matters before requesting servicing.
Problem Check Reference Page
* Has the power plug become disconnected from the outlet? * Is the lamp cover properly attached? * Has the internal temperature become high? When the internal temperature becomes very high, to protect the unit the power will not switch on. * Has the lamp timer exceeded 1,100 hours? The power will no longer switch on once the timer has exceeded 1,100 hours.
* Has the connected input been selected? * Is the cable of the input connector properly connected? * If there is connection to a personal computer, is a signal being output from the personal computer? * Has a signal that is higher than the supported fre- quency of the projector been input? * Check that the image adjustment brightness and con- trast are not set to minimum. * Has the lamp burned out? * Is the STATUS indicator flashing?
E-62 E-61
* Is the projector installed properly? * Is the keystone adjustment properly adjusted?
* Is the lens properly focussed? * Are the projection screen and the projector installed at the proper distance? * Has the projection distance exceeded the focussing range? * Is there condensation on the lens and other parts? When the projector has been stored in a cold location and the power is switched on in a warm location, there may be condensation on the lens and other internal optical parts. Should this occur, wait several minutes until the condensation disappears.
Image position is shifted and doesn't display prop- erly
* Is the input signal being supported for resolution and frequency? Check the resolution of your personal com- puter.
* When the image is broken in the horizontal or vertical direction, or the image does not fill the entire screen, select a suitable aspect ratio.
Overall color of image is strange
* When a component signal is being input, the color space setting is different. Perform the color space setting.

Problem Check Reference Page
Menu name cannot be se- lected
* Other than for "Setup" and "Info.", selection is not per- mitted unless a signal is input to the projector and an image or picture is projected.
Pressing the PIP button does not display a sub-pic- ture
* There will not be a display unless the personal com- puter screen is being projected. An image will not be output unless a video image is being input.
Remote control does not function
* Has the transportation insulation sheet been re- moved? * Is an obstacle located between the remote control and the remote control sensor of the main unit? * Is the remote control out of range for its signal to reach the sensor? * Is there strong light or a fluorescent lamp in the vicin- ity of the sensor? * Are the batteries weak? Try directing the remote con- trol toward the remote control sensor from a close distance and operating it. If there is difficulty in chang- ing settings, the batteries are weak. Replace the bat- teries with new ones.
STATUS indicator lights or flashes
* See the STATUS indicator list.

Cleaning a Soiled Projector Main Unit * Wipe with a lint-free, soft, dry cloth. When very dirty, wipe with a cloth that has been moistened with a diluted neutral detergent, then finish with a dry cloth. If a chemically-treated cloth is going to be used, please follow any written warnings. * Do not wipe with thinner, benzene, or other solvents. Doing so could cause them to undergo qualitative changes or the coatings may peel, etc. * When removing the dust of the outflow and intake holes, use the brush attachment on a vacuum cleaner to clean out the dust. Avoid using the vacuum directly without attaching the adapter as well as the use of a nozzle adapter. * Do not scratch or otherwise hit the projector body with your nails or other hard object, since this will cause scratches.
Dirty Lens * Clean using the same method you would use to clean a camera lens: Use a commercial blower for camera use or cleaning paper for eye glasses. Be careful not to scratch the lens at this time.
Dust of the Intake and Outflow Holes Dust that collects in the intake and outflow holes will obstruct the ventilation and cause the internal temperature to rise which could cause damage. Clean this area carefully. As a guideline, clean at least every 100 hours.

* Switch off the power, check that the POWER indicator has changed to a steadily lit amber, then unplug the power cable. * Clean out the holes from the outside using a vacuum cleaner. Use the brush adapter of the vacuum cleaner to do this. Avoid using the vacuum directly without attaching the adapter as well as the use of a nozzle adapter.
Cleaning the Inside of the Projector Cleaning of the inside of the projector is required about once a year. Failure to clean over a long period while dust has collected inside the projector could cause a fire or breakdown. Do not clean the inside of the projector by yourself. Please be sure to contact your dealer.

The lamp as a light source used in the unit has a lifespan. The rated lamp life is about 1,000 hours. The rated lamp life is the average life of the lamps produced and tested (under the test conditions of our company) for a long term, however, it may become shorter depending on the conditions of usage.
After the lamp has been operating for 1000 hours or longer, the STATUS indicator will light and total lamp usage will be displayed on the screen. The unit will not turn on after 1100 hours. When this happens, replace the lamp cartridge with a new one. Follow the procedures below for replacement.
The rated lamp life is about 1,000 hours. The rated lamp life is the average life of the lamps produced and tested (under the test conditions of our company) for a long term, however, it may become shorter de- pending on the conditions of usage. After the lamp has been operating for 1000 hours or longer, the STATUS indicator on the control panel will light and the “LAMP USAGE” icon which shows hours of total lamp usage will be displayed on the screen. When this happens, turn off the unit and replace the lamp cartridge with a new one. The unit will not turn on after 1100 hours. (It will go off if it is in use.)

PREPARATION Turn the projector upside down and place it on a soft cloth that has been prepared in advance to prevent scratches. This will assist in lamp cartridge replacement. After replacement, return the projector to the original condition. 1. Disconnect the power cable. 2. Turn the projector upside down. 3. Remove the lamp cover.

(1) Turn the screw that fastens the lamp cover
(2) Lift the lamp cover a little and pull it off in the
counterclockwise until it turns freely. (The screw will not come out.)
(1) Turn the 2 screws that fasten the lamp cartridge
(2) Grasp the handle of the lamp cartridge, pull it

counterclockwise until they turn freely. (The screws will not come out.)

5. Install the new lamp cartridge
(1) Slowly push in the lamp cartridge with the
(2) Turn the 2 screws of the lamp cartridge clock-
socket facing forward. (Align the lamp cartridge screw with the screw hole of the projector.)
wise to tighten.
(1) First insert the front edge of the lamp cover into
(2) Turn the screw of the lamp cover clockwise to
the groove, then close the lamp cover.
tighten.
Plug in the power cable and switch on the power before resetting. Select [Info.] → [Lamp Timer Reset] and then reset the hours indication.
NOTE: The projector will no longer start when the lamp timer exceeds 1,100 hours. As a result, it will not be possible to reset the lamp timer through timer operations. Should this situation arise, set to the standby condition and press the SOURCE button and the ASPECT button of the main unit at the same time for at least 5 seconds. When reset, the STATUS indicator will go off. Please obtain a replacement lamp from your dealer. When ordering, please specify a V-1080/V-807 special re- placement lamp type V-120 (order code 28-060).

Optical DMDTM Single Chip Digital Micro Device (DMDTM) V-1080: 1024 768 dots V-807: 800 600 dots Lamp 120 W high-pressure mercury lamp Image size V-1080: 36 inch to 200 inch V-807: 35 inch to 200 inch Light Output 800 ANSI lumens Contrast Ratio 800:1 (Full on/off)
Electrical Inputs Video (NTSC3.58/NTSC4.43/PAL/PAL_N/PAL_M/PAL60/SECAM) RGB (Horizontal :15 to 85 kHz, Vertical 50 to 120 Hz) Color Reproduction Full color (16,770,000 colors) Resolution V-1080: SXGA (Compression), XGA(True), SVGA/VGA (Expansion/True) V-807: XGA (Compression), SVGA (True), VGA (Expansion/True) Input Current 1.8 A Power Requirement 100 - 240 V AC, 50/60 Hz Power Consumption 160 watts
Mechanical Dimensions Excluding Stand 18.0 cm (W) 4.5 cm (H) 14.1 cm (D) 7.1 in.(W) 1.8 in.(H) 5.6 in.(D) Weight Approximately 0.9 kg / 1.98 lbs Operational Temperatures Data projector: 5° to 35°C (41° to 95°F), 30 to 85% humidity Regulations UL Approved (UL 1950, CSA 950) Meets FCC Class A requirements Meets EMC Directive (EN55022, EN55024) Meets Low Voltage Directive (EN60950)
* Specifications and design are subject to change without notice.

The unit automatically determines PC signals to select the appropriate resolution. Some signals may require manual adjustments. See "Picture Adj./Fine Picture /H Position / V Position" on pages E-47 and E-48.
Signal Resolution Frequency H. Refresh Rate Digital Analog ( kHz ) ( Hz ) V-1080 V-807 V-1080 V-807
VESA 640 350 31.5 70.1 – – 640 350 37.9 85.1 – – 720 350 31.5 70.0 – – 640 400 31.5 70.1 – – 640 400 37.9 85.1 – – 720 400 31.5 70.0 720 400 37.9 85.0 – – 640 480 31.5 60.0 640 480 37.9 72.8 – – 640 480 37.5 75.0 – – 640 480 43.3 85.0 – – 800 600 35.2 56.3 – – 800 600 37.9 60.3 800 600 46.9 75.0 – – 800 600 48.1 72.2 – – 800 600 53.7 85.1 – – 1024 768 48.4 60.0 1024 768 56.5 70.1 – – 1024 768 57.7 72.0 – – 1024 768 60.0 75.0 – – 1024 768 68.7 85.0 – – 1280 1024 64.0 60.0 – – 1280 1024 80.0 75.0 – – – 1280 1024 91.1 85.0 – – – NEC(PC-9800) 640 400 24.8 56.4 – – 640 400 31.5 70.1 – – 640 480 31.5 60.0 – – 640 480 37.5 75.0 – – 800 600 37.9 60.3 – – 800 600 46.9 75.0 – – 1120 750 50.0 60.1 – – 1024 768 56.5 70.1 – – 1024 768 60.0 75.0 – – 1280 1024 64.6 59.9 – – – Apple Macintosh 640 480 35.0 66.7 – – 832 624 49.7 74.5 – – 1024 768 60.2 74.9 – – 1152 870 68.7 75.1 – – Sun 1152 900 61.8 66.0 – – 1280 1024 81.1 76.1 – – SGI 1024 768 49.7 60.4 – – 1280 1024 63.9 60.0 – – – 1152 900 71.7 76.1 – – HP 1280 1024 78.1 72.0 – – –
V-1080: The native resolution of the panel is 1024768. Resolutions other than 1024768 may be displayed with uneven size of text or lines.
V-807: The native resolution of the panel is 800600. Resolutions other than 800600 may be dis- played with uneven size of text or lines.

AUTO SOURCE
POWER
STATUS POWER
141 (5.6)
180 (7.1)
45 (1.8)


PLUS Industrial Corporation is certified to ISO 9001. Certificate No. Q1001219118017.
Otowa Head Office and PLUSLAND of PLUS Corporation and PLUS Industrial Corporation are certified to ISO 14001. Certificate No. NQE-9809008A.
* PLUS Vision Corp. is certified to ISO 14001 as a member of the PLUS group.
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.