Instruction/ maintenance manual of the product POE-152S-5V Planet Technology
Go to page of 11
- 1 - IEEE 802.3af Pow er ov er Ethernet Splitter POE-152S-5V/12V User’s Manual.
- 2 - Trademarks Copyright PLANET Technol ogy Corp. 200 6. Contents subjec t to revisio n without prior notice. PLANET is a registered trademark of PLANET Technology Corp.
- 3 - TA BLE OF CONTENTS 1. INTRODUCT ION ........................ ....................................................... ....................................................... .... 4 1.1 C HECKLIST ................................... ..............
- 4 - 1. INTRODUCTION 1.1 Check list Thank you for purchas ing our POE-152S IEEE 802.3af Power over Ethernet Splitter, your Power over Ethernet Splitter package shall contain followi ng contents: Chec.
- 5 - 1.4 Spec ification Model POE-152S Ethernet Con nector 2 x RJ-45 (1 for Data + DC in, 1 fo r Data out) Ethernet Dat a Rate 10/100/1 000Mbps (vary on Ethern et device a ttached) Output Volta ge/Current Vary on mode l: POE-152S-5V: 5VDC, 2 .5A max.
- 6 - 2. HA RDWA RE INSTA LLA TION These products provide three different running speeds – 10M bps, 100Mbps,1000M bps. in the same device and auto- matica lly distin guish th e speed of inco ming co nnectio n. This se ction desc ribes the hardware feature s of POE-152S.
- 7 - 2.2 POE -152 and PO E-152S, the IEEE 802 .3af Injector and S plitter installation 1. Conn ect a stand ard ne twork ca ble from “Ethern et+DC” of POE-152 to “Ethernet+DC” of POE-152S. The POE L ED of POE-152 / POE-152S will light on continu ance.
- 8 - 2.3 Connect w ith IE EE 802. 3af devices The POE-152S can also provide the alterna tive to make the non- IEEE 802.3af d evices the possi bility to c onnect with an IEEE 802.3a f in-line power device li ke Power over Etherne t Switch, then c onnect proper DC plu g from " DC OUT" of POE-152S to rem ote device .
- 9 - 3.TROUBLESH OOTING This cha pter contai ns informat ion to help you solve iss ues. If the POE-152S is not func tioning prop erly, m ake sure the POE-152S was set u p accord ing to i nstructio ns in th is man ual. The PoE LED is not lit Solution : Check th e cable connec tion between POE-15 2S and IEEE 8 02.
- 10 - A PPENDIX A NETWORKING CONN ECTION A .1 Sw itch‘s RJ-45 Pin Assignments 1000Mbps, 1000B ase T Contact MDI MDI-X 1 BI_DA+ BI_DB+ 2 BI_DA- BI_DB- 3 BI_DB+ BI_DA+ 4 BI_DC+ BI_DD+ 5 BI_DC- BI_DD-.
- 11 - There are 8 wires on a s tandard UTP/STP cable and each wire is col or-coded . The f ollowing shows the p in alloc ation and col or of stra ight cab le and c rossover c able con nection : Figur.
An important point after buying a device Planet Technology POE-152S-5V (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Planet Technology POE-152S-5V yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Planet Technology POE-152S-5V - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Planet Technology POE-152S-5V you will learn all the available features of the product, as well as information on its operation. The information that you get Planet Technology POE-152S-5V will certainly help you make a decision on the purchase.
If you already are a holder of Planet Technology POE-152S-5V, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Planet Technology POE-152S-5V.
However, one of the most important roles played by the user manual is to help in solving problems with Planet Technology POE-152S-5V. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Planet Technology POE-152S-5V along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
