Instruction/ maintenance manual of the product PL1900 Planar
Go to page of 28
PL1900.
1195 NW Compton Drive Beaverton, OR 97006-1992 www.planar.com Customer Service Planar provides the following technical support services: Internet Support For support available 24/7 visit Planar's Online Technical Support at www.planar.com/support.
1.
2 The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright.
3 TABLE OF CONTENTS For Your Safety For Your Safety --------------------------------------------------------------- 4 General Notes Special notes on LCD monitors --------------------------------------.
4 For Your Safety Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FO.
5 PRECAUTIONS z Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. z Do not place the monitor on an unst able cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance.
6 GENERAL NOTES SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. NOTES • Due to the nature of the fluore scent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears.
7 BEFORE YOU OPERATE THE MONITOR FEATURES • 48.0cm(19”) TFT Color LCD Monitor • Crisp, Clear Display for Windows • Recommended Resolutions: 1280 X 1024 @60Hz • EPA ENERGY STAR ® • Space S.
8 Installation Instructions Pow er Source: 1. Make sure that the power cord is the correct type required in your area. 2. This LCD monitor has an External universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required.
9 Installation Instructions CABLE CONNECTIONS Connecting the Signal Cable: the LCD monitor comes with a built-in signal cable. Plug the signal cable ′ s 15-pin connector into the computer's VGA port and tighten the two screws on the cable connector.
10 Installation Instructions ADJUSTING THE VIEWING ANGLE • For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’ s angle to your own preference. • Hold the stand so you do not topple the monitor when you change the monitor’s angle.
11 OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (See Figure 3). By changing these settings, the picture can be adjusted to your personal preferences.
12 OPERATING INSTRUCTIONS(cont.) • Pow er Button: Press this button to switch ON/OFF of monitor’s power. • MENU / ENTER : Active OSD menu or function adjust confirm or Exit OSD menu when in Brightness/Contrast OSD status. • Contrast : Adjust contrast or function adjust.
13 OPERATING INSTRUCTIONS (cont.) HOW TO ADJUST A SETTING 1. Press the MENU-button to activate the OSD window (Figure 4). 2. Press or to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate it. If the function selected has a sub-menu, press or again to navigate through the sub-menu functions.
14 OPERATING INSTRUCTIONS (cont.) ADJUSTING THE PICTURE The descriptions for function control LEDS Main Menu Item Main Menu Icon Sub Menu Item Sub Menu Icon Description Luminance Contrast Contrast from Digital-register. Brightness Backlight Adjustment.
15 OPERATING INSTRUCTIONS (cont.) Main Menu Item Main Menu Icon Sub Menu Item Sub Menu Icon Description OSD Setup H.Position Adjust the horizontal position of the OSD. V.Position Adjust the vertical position of the OSD. OSD Timeout Adjust the OSD timeout.
16 PLUG AND PLAY Plug & Play DDC 2B Feature This monitor is equipped with VESA DDC 2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.
17 TECHNICAL SUPPORT (FAQ) Problem & Question Possible Solution Power LED is not on *Check if the Power Switch is in the ON position *Power Cord should be connected No Plug & Play *Check if the PC system is Plug & Play compatible *Check if the Video Card is Plug & Play compatible *Check if the D-15 plug pin of Video Cable is bent.
18 TECHNICAL SUPPORT (FAQ) (cont.) CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the picture has not correct width. FOCUS adjusts the phase of the pixel clock signal.
19 APPENDIX SPECIFICATIONS Driving system TFT Color LCD LCD Panel Size 48.0cm(19") Pixel pitch 0.294mm( H ) × 0.294mm( V ) Video R,G,B Analog Interface Input Separate Sync. H/V TTL H-Frequency 30kHz – 83kHz (Analog) V-Frequency 55-75Hz (Analog) Display Colors 16.
20 APPENDIX (cont.) Switch • Auto Adjust Key • Brightness • Contrast • Power Button • MENU External Controls: Functions • Contrast • Brightness • Focus • Clock • H.
21 APPENDIX (cont.) Preset Display Modes STANDARD RESOLUTION HORIZONTAL FREQUENCY VERTICAL FREQUENCY Dos-mode 720 × 400 31.469kHz 70.0Hz VGA 640 × 480 31.470kHz 60.0Hz 640 × 480 37.500kHz 75.0Hz SVGA 800 × 600 37.879kHz 60.0Hz 800 × 600 46.875kHz 75.
22 APPENDIX (cont.) CONNECTOR PIN ASSIGNMENT 15 6 10 11 15 15 - Pin Color Display Signal Cable PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1. Red 9. +5V 2. Green 10. Ground 3. Blue 11. Ground 4. Ground 12. DDC-Serial Data 5. Detect Cable 13. H-Sync 6. R-Ground 14.
.
.
.
Q41G19M1935 1A 1195 NW Compton Drive Beaverton, OR 97006-1992 www.planar.com © 2010 Planar Systems, Inc. Planar is a registered trademark of Planar Systems, Inc. Other brands and names are the property of their respective owners. Technical information in this document is subject to change without notice.
An important point after buying a device Planar PL1900 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Planar PL1900 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Planar PL1900 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Planar PL1900 you will learn all the available features of the product, as well as information on its operation. The information that you get Planar PL1900 will certainly help you make a decision on the purchase.
If you already are a holder of Planar PL1900, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Planar PL1900.
However, one of the most important roles played by the user manual is to help in solving problems with Planar PL1900. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Planar PL1900 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
