
Graphic EQ (9 bands): Q = 1.414, ISO octave centers ±15 dB @ 63, 125, 250, 500 1k, 2k, 4k, 8k, 16k Hz
Mixer Section:
Main Mixer, Monitor, & Effects: +4 dBu
Maximum Main Mixer Section Output:+20 dBu
Frequency Response
Maximum Input Levels
Mic Input to Main Mixer Output (Trim at 0 dB): +0, –1 dB, 32Hz to 20kHz +0, –3 dB, 16Hz to 80kHz
Mic Input: –20 dBu, Trim @ 0 dB (HI) +20 dBu, Trim @ –40 dB (LOW) Line Input: 0 dBu, Trim @ 0 dB (HI) +40 dBu, Trim @ 40 dB (LOW) Insert Input: +20 dBu Stereo Line Input: +20 dBu Tape Input: +20 dBu Effects Return: +20 dBu Power Amp In: +22 dBu
Mic Input to Power Amp Output @ rated power out put: +0, –1 dB, 32Hz to 20kHz +0, –3 dB, 16Hz to 55kHz
Mic Input to Main Mixer Output: < 0.005% @ +4 dBu out put
Mic Input to Power Amp Output: < 0.15%, 250mW to rated power
Minimum Input Level to produce +4 dBu @ Main Mixer Out put
Mic Input: –68 dBu Insert Input: –28 dBu Line Input: –48 dBu Stereo Line Input: –28 dBu Tape Input: –18 dBu Effects Return: –18 dBu
60 dB @ 1kHz, Trim @ 0 dB
Noise 20Hz to 20kHz BW (150 Ω source impedance)
Equivalent Input Noise (EIN): –127 dBu
Maximum Voltage Gain
Master & 1 input channel @ nominal (–10 dB & –20 dB), Trim @ 0 dB –85 dB
Stereo Line Input to Tape Output: 20 dB Main Mixer Output: 32 dB
Adjacent Inputs or Input to Output: –90 dB @ 1kHz Fader Off –90 dB @ 1kHz Break Switch Mute –80 dB @ 1kHz
Effects Return to Main Mixer Output: 22 dB Monitor Output: 22 dB
Input Level Trim Control Range
Input Impedance
0 to –40 dB
Mic Input: 3 kΩ, balanced Insert Input: 10 kΩ, unbalanced Line Input: 40 kΩ, balanced Stereo Line Input: 10 kΩ, unbalanced Tape Input: 10 kΩ, unbalanced Effect Return: 10 kΩ, unbalanced Power Amp In: 10 kΩ, unbalanced
+15V DC
Equalization
Rumble Reduction: 75Hz, –18 dB/octave
Channel EQ: High ±15 dB @ 12kHz Mid ±12 dB @ 2.5kHz Low ±15 dB @ 80Hz

Channel Separation
Main Mixer Output: 150 Ω Insert Output: 150 Ω Tape Output: 150 Ω Monitor Output: 150 Ω Effects Send: 150 Ω Power Amp Out: 0.032 Ω @ 1kHz
Damping Factor
> 250 @ 1kHz
Amp Input Impedance
10 k Ω unbalanced, 20 k Ω balanced
Digital Effects
Resolution: 16-bit, 2-channel
Input Sensitivity
Sample Rate: 31.25kHz
406M, 408M, 408S 1.35 volts (+4.8 dBu) for rated power into 4 ohms
VU Meters
808M, 808S 1.76 volts (+7.1 dBu) for rated power into 4 ohms
Power Amplifi er Section:
26.4 dB (21V/V)
Maximum Input Level
Maximum Power at 1% THD, midband, both channels driven
9.75 volts (+22 dBu)
406M, 408M, 408S
250 watts per channel into 2 Ω 200 watts per channel into 4 Ω 125 watts per channel into 8 Ω
406M, 408M, 408S < 5µs
808M, 808S < 6.2µs
808M, 808S
Slew Rate
600 watts per channel into 2 Ω 450 watts per channel into 4 Ω 300 watts per channel into 8 Ω
808M, 808S > 50V/µs
Continuous Sine Wave Average Output Power, both chan nels driven (rated power)
Load Angle
8(±jx) time in de pen dent at 8 Ω 4(1±jx) time dependent at 4 Ω
180 watts per channel into 4 Ω from 40Hz to 20kHz, with no more than 0.15% THD
110 watts per channel into 8 Ω from 40Hz to 20kHz, with no more than 0.10% THD
No latch up at any frequency or level.
808M, 808S
Unconditionally stable, driving any reactive or capacitive load
340 watts per channel into 4 Ω from 40Hz to 20kHz, with no more than 0.15% THD
240 watts per channel into 8 Ω from 40Hz to 20kHz, with no more than 0.10% THD
AC Power Requirements
Power Bandwidth
United States: 120VAC, 60Hz
< 10Hz to 30kHz (+0, –1 dB) @ rated power into 4 Ω
Frequency Response
Japan: 100VAC, 50/60Hz
< 10Hz to 30kHz (+0, –1 dB) < 10Hz to 55kHz (+0, –3 dB)
(Capable of operation from 75% to 110% of rated line voltage)
Distortion
Physical
> 105 dB below rated power into 8 Ω
Weight:
406M, 408M, 408S 32 pounds (14.5 kg)
808M, 808S 36 pounds (16.3 kg)



LEFT SPEAKER
LEFT SPEAKER

63 125 250 500 1K 2K 4K 8K 16K
75Hz HPF 63 125 250 500 1K 2K 4K 8K 16K

LEFT SPEAKER
LEFT SPEAKER

63 125 250 500 1K 2K 4K 8K 16K
75Hz HPF 63 125 250 500 1K 2K 4K 8K 16K


1K 500 250 63 125 16K 2K 4K 8K
R L R L R L R L R L R L R L R L
VOLUME CH. VOLUME CH. VOLUME CH. VOLUME CH. VOLUME CH. VOLUME CH. VOLUME CH. VOLUME CH.
MIC 1 MIC 2 MIC 3 MIC 4 MIC 5 MIC 6
120 VAC 60HZ 320W 408S 2 X 250W STEREO
RISK OF ELECTRIC SHOCK
POWER
DO NOT OPEN
REPLACE WITH THE SAME TYPE FUSE AND RATING. DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE
UTILISE UN FUSIBLE DE RECHANGE DE MÊME TYPE. DEBRANCHER AVANT DE REMPLACER LE FUSIBLE
SPEAKER OUT
120 VAC 60HZ 320W 408M 2 X 250 WATTS
RISK OF ELECTRIC SHOCK
POWER
DO NOT OPEN
REPLACE WITH THE SAME TYPE FUSE AND RATING. DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE
UTILISE UN FUSIBLE DE RECHANGE DE MÊME TYPE. DEBRANCHER AVANT DE REMPLACER LE FUSIBLE
POWER AMP 1 / MAIN POWER AMP 2 / MONITOR
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.