Instruction/ maintenance manual of the product hobby serger Pfaff
Go to page of 14
PFAFF 41P HOBBY SERGER.
ow po.
IMPORTANT SAFEGUARDS • Never bend loopers and needle while threading and sewing. • Before connecting machine be sure voltage on AC adaptor matches your electrical outlet. • Disconnect AC adaptor from socket outlet when changing needle or when leaving machine unattended.
PRINCIPAL PARTS 10. Needle clamp body holds needle in machine 11. Presser bar 12. Thread guide 13. Needle - Style 2020 size 14 14. Seam guide (#287624) helps keep seam allowance even. 15. Lower looper forms lower stitch. 16. Upper looper forms upper stitch.
ACCESSORIES 3 each x Thread cap (large size) #287537 I 3 x Demo thread spool (on machine) • Raise presser foot. (Push down on lever) • Plug adaptor (1) into electrical outlet to power machine and turn on light (under needle plate) for threading. Note: When foot switch plugged in light will go out.
MLJJUIIrIU IMHLAU ItNSIUN • Plug in adaptor and foot switch. (If not already plugged in) Note: Foot switch comes from factory on low speed. Internal threading light turns ott when switch is plugged into machine. • Press foot switch to continue sewing fabric ( under presser foot).
PREPARATION FOR THREADING • Your machine comes threaded. If you wish to change thread, an easy method for threading is tying on threads. (refer to page 5) • If machine runs out of thread, it is necessary to rethread machine. (refer to Page 6) • Unplug foot switch.
Use tweezers to place thread into two discs. • Raise lower looper to near internal cover (about width of tweezers). This is optimum position for threading lower looper. • Insert threader into left side hole (A-4). • Hold tweezers in right hand and guide thread through threader.
Di /T needle clamp body THREADING PATH B (UPPER LOOPER) STEP 2 Bi iL 2ZYf&I B • Draw thread of spool (B) through guide (B-i). • Pull thread down to guide (B-2). • Use tweezers to place thread into two discs. • Turn handwheel toward Lower needle clamp body to lowest position.
‘HREADING PATH C (NEEDLE) STEP 3 • Use tweezers to place thread into two discs. • Pull thread down through guide (0-3), then up and down through it again. • Collect threaded threads and place under presser foot. —4( c-I • Draw thread of spool (C) through guide (C-i).
START TO SEW _________________ SECURING TAIL CHAINS Note: edge guide is preset to limit stitch _______________________________ needle clamp width to approximately 11/64 inch (4.2mm). body __ • Place needle clamp body to lowest • Apply liquid fray preventer.
I H . RESTITCH PART OF SEAM Raise presser foot. (I • Pivot fabric. down on lever) • Insert needle at edge. • Place fabric under presser foot. • Continue stitching. • Adjust fabric to overlap previous • Lower presser foot. nside Corner — 4 .
BLINDSTITCH DECORATiVE FLATLOCK ongde 4.2mm — 0 • Fold hem to wrong side. • Fold hem back as shown. LI • Place folded edge against seam guide. • Stitch making sure needle just barely catches the fold. • Turn fabric to right side and press.
JOIN TWO PIECES OF FABRIC CHANGING NEEDLE PERFORMANCE CHECKLIST Whenever sewing difficulty is encountered, hard. • Loose needle set screw. Important: For best results. use only Needle style 2020 size 14. • Insert flat side of needle to the back as far up as it will go.
An important point after buying a device Pfaff hobby serger (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pfaff hobby serger yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pfaff hobby serger - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pfaff hobby serger you will learn all the available features of the product, as well as information on its operation. The information that you get Pfaff hobby serger will certainly help you make a decision on the purchase.
If you already are a holder of Pfaff hobby serger, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pfaff hobby serger.
However, one of the most important roles played by the user manual is to help in solving problems with Pfaff hobby serger. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pfaff hobby serger along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
