Instruction/ maintenance manual of the product hobby 1010 Pfaff
Go to page of 15
INSTRUCTION MANUAL FOR SEWING MACHINE 0] Hobby Model 351427004 0012.14 1010 — 37.
IMF’UHIANT 5AFTY INSTRUCTIONS When using an electrical appliance, basic safety precautions should always be followed, including the following: Read all instructions before using (this sewing machine) DANGER To reduce the risk of electric shock: An appliance should never be left unattended when plugged in.
NAME OF PARTS (FRONT VIEW) (REAR VIEW) Thread tension dial Bobbin winder Stop Motion knob Hand wheel Bobbin winder spindle Face cover Presser toot Shuttle Extension table Thumb screw Needle plate Zigz.
ACCESSORIES Bobbin Button foot Button hole cutter Felt Zigzag foot (On machine) Machine Oil Screw driver Button hole foot Zipper foot I Needle #11 #14 BEFORE SEWING 1 Fit plug into the machine. 2. Plug the machine to the po y supply. 3. Sewing speed can be varied the foot control.
REMOVING EXTENSION TABLE 1 Hold the left end of table and pull out in diecfion or arrow. WINDING ThE BOBBIN 1 Release stop motion kric 2.Thread as shown. 3.When bobbIn is filk tighten stop motion kno 1. This sewing machine can be used as a fiat bed machine but easily converts to free arm machine by removing the extension table.
2.Open hinged latch of bobbIn case and pull bobbin case out of machine. INSERTING BOBBIN INTO BOBBIN CASE 1.Raise needle to its highest position, pulling thread to the front, open the latch of bobbin case and hold it. I .PulI off 5cm of thread from bobbin and insert it into bobbin case as shown.
THREADING UPPER THREAD 1. Hold upper thread with left hand, turn the hand wheel slcwly towards you until the needle qoes down and comes up. Then stop the hand wheel when the takeup lever is at its highest position. Lightly draw up the upper tbread and the lower thread will be brought up in a loop.
ADJUSTiNG THREAD TENSION CONTROL DIAL Weak Strong Upper thread tension may be adjusted by turning the thread tension dial. Fabric Coaect Incorrect Inside of fabric Upper thread Upper thread Bobbin tbread LOWER THREAD TENSION Lower thread tension can be adjusted by turning screw on bobbin case slight ly to the right (clock-wise) to increase tension.
REGULATING THE PRESSER FOOT PRESSURE 1. Push down inner pin (A) to increase pressure. (Light to medium fabrics) 2. Push down outer ring to release pressure. (Heavy fabrics) 3. Insufficient pressure may cause poor feeding, skipped stitches, or difficulty in guiding the fabric.
FABRIC THREAD NEEDLE TABLE TO START SEWING Please note that the following list is a guide when sewing different fabrics. Important Hints 1. Raise the takeup lever to its highest position before starting and after stopping sewing. 2. Hold both threads about 10 cms to the rear of machine for the first two or three stitches.
TO FINISH SEAM 1 .Sew to the edge of seam. 2.Push the reverse button and sew in reverse ‘for about 3-4 cms. 3.Raise needle to its highest position. 4.Lift presser foot and pulloul the fabric to rear of machine. STRAIGHT STITCH 1 This type of stitching is the one used most frequently.
BLflTON SEWING 1 .Lower drop feed. 2. Place button attaching presser foot in position. 3.Place button between presser foot and fabric and lower presser foot. 4.Manually turn hand wheel towards you ensuring that the needle enters into both holes of button wfthout obstruction.
HEMMING Note: Hemmer foot can be purchased separately. 1. Raise the foot and the needle to its highest position. Replace the toot with the hemmer foot. 2. Fold over the fabric edge by about 3mm and place it under the foot. Secure the folded edge with a few stitches.
QUILTER Note: Quilt guide can be purchased separately. BUTTONHOLE SEWING 1.MARK WITH A PENCIL OR CHALK THE EXACT LENGTH OF THE BUTTONHOLE ON THE FABRIC. 2. REMOVE THE REGULAR PRESSER FOOT AND ATTACH THE BUTTONHOLE FOOT & PUT THE FAE UNDER ThE BUTTONHOLE FOOT.
9 U’ 5. .4 “I C, .4 CD C. 0 C z C. CD C. CD 0 -4. C. CD C. 0 CD CD C) CD DC CD CD CD C. 0. 0 CD 0 CD .4 0 ‘C 0 ‘C CD DC 0. 0 0 z ‘a, 0. DC r CD p. (fl Cl) r’ T DC 3’ .4 ,.4 ,- In -‘ .4 0 CD 0 . o 0 CD o , .C CD CD — DC DC C DC DC DC • ‘ CD CD (V DC 0 0 - 0 ‘2: .
An important point after buying a device Pfaff hobby 1010 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pfaff hobby 1010 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pfaff hobby 1010 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pfaff hobby 1010 you will learn all the available features of the product, as well as information on its operation. The information that you get Pfaff hobby 1010 will certainly help you make a decision on the purchase.
If you already are a holder of Pfaff hobby 1010, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pfaff hobby 1010.
However, one of the most important roles played by the user manual is to help in solving problems with Pfaff hobby 1010. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pfaff hobby 1010 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
