Instruction/ maintenance manual of the product FB-0-1-2-4 Peugeot
Go to page of 26
WORKSHOP MANUAL 50 cm3 Motor FB-0-1-2-4 GB.
Trekker - Squab CONTENTS ENGINE P ART CYCLE P ART RECOMMENDA TIONS ELECTRIC EQUIPMENT 1 Designation Page - Contents, ............................................................. 1 - Main characteristics, ............................................ 2 - Maintenance plan, .
Trekker - Squab TECHNICAL DA T AS Frame ENGINE MARKING XXXXXXXX FB2 Number T ype Main spécifications 2 IDENTIFICA TION MARK Identification plate FB2 ENGINE Forced-air cooled 2 stroke engine : - Bore and stroke : ......................................
Trekker - Squab MAINTENANCE PLAN C PLAN A PLAN B 500 km or 3 mois 5000 km or 2500 km* 10000 km or 5000 km* * reforced maintenance 3 Depending on how the scooter is used, it is recommended to apply either - The normal maintenance plan or - The reinforced maintenance plan.
Trekker - Squab INSTRUCTIONS FOR MAKING OPERA TIONAL 4 1. Preparation of the battery (dry charged) - Remove the battery . - Remove the six cell caps and the breather tube cap. - Fill the battery with électrolyte up to the level marked UPPER LEVEL (35% sulphuric acid 1.
Trekker - Squab TIGHTENING TORQUES AND SPECIAL TOOLS TIGHTENING TORQUES SPECIAL T OOLS 5 Engine Assembly screws for : - Housings : ........................................................ 1m.daN - Covers : .............................................
Trekker - Squab REMOV AL 6 64765 752026 68 007 750806 Removal of the engine - Remove : - All side casings - Disconnect : - Fuel line from the carburettor , - Fuel tap vacuum hose, - Oil pump control c.
Trekker - Squab 752370 7 REMOV AL Removal of the oil pump - Unclip the oil inlet pipe to the carburettor . - Unscrew the 2 hex head socket screws. - Remove the oil pump and the control flange. - Remove the 2 square fastening nuts Q from their housings.
Trekker - Squab REMOV AL 8 752237 Rdl 12,35x19,75x1 Make careful note of where this tool comes level with the starter ring gear plate of the starter motor in order to make sure, when refitting, that the pressure plate fits correcte into the grooves of the crankshaft.
Trekker - Squab REMOV AL 9 750807 64706 752168 69098 Removing the cylinder and piston - Remove the cylinder and cylinder-to- crankcase gasket. - Pack the crankcase mouth with clean cloth or paper . - Lean the engine to the left and take out the wrist pin’s RH snap ring.
Trekker - Squab 752168 750069 REFITTING 10 64706 64710 69104 750808 Closing the crankcase halves - Position both locating dowls in the LH crankcase: - Put the crankcase gasket in place (no oil, no grease). - Position the RH crankcase and fit it on being careful not to damage the oil seal where it meets the cotter key .
Trekker - Squab REFITTING 11 côté couvercle ARBRE INTERMÉDIAIRE rondelle souple rondelle métal Refitting the transmission case - Replace the oil seals and bearings if necessary by the appropriate “ heating and drift >, method. - Check that the outlet channels are clear : Removal of the case.
Trekker - Squab REFITTING / FITTING 12 2 752127 752361 1 C. Refit the primary transmission. Fitting a variator W arning: do not delete any piling up element or reduce the dimensions. This would lead to a tightening of the nut on the grooves of the crankshaft assembly and not on the fixes driven face and hence would destroy the crankshaft assembly .
Trekker - Squab FITTI NG 13 Good 1 No good 2 1 Fitting the reed valve and intake pipe - Check: the condition of the petals and the seats. - lnstall in the following order on the crankcase: - Fasten all the parts using 4 screws (L = 28mm), and tighten to 1 m.
Trekker - Squab Bleed screw FITTING 14 Mark PARTIE CYCLE Fitting the cooling systern - Position and fasten the fan onto the rotor (4 screws L = 1 8). T ighten to 1 m.dan. - Position and fasten the cylinder case and cooling cover (4 screws M = 25). Make sure that it is fastened correctly around the sensor .
Trekker - Squab ELECT RIC EQUIPMENT 15 a b 5k Ω 5k Ω 3 4 5 6 1 26 5 on off 6 3 1 4 2 12V 4Ah 15 c a 1 10 8 7 6,7 Ω 5w 9 5,9 Ω 30w 11 26 B 1,2w 5/21w 12V 4Ah A 0,75 Ω 4w 13 3 x 1,2w 15w 15 14.
Trekker - Squab 16 ELECT RIC EQUIPMENT a d b c 1 110 Ω 750 Ω 0,4 Ω 0,7 Ω V alue flywheel control 1 - Flywheel a - ignition b - sensor c - alternative current d - battery charge current 1 - Y e.
Trekker - Squab C 5/21w 12V 4Ah 4x 10w D 1,2w 1,2w E 5 on off 5A 0,75 Ω 4w 6 3 1 4 10/07/97 25 26 15 24 14 27 16 23 22 20 19 21 17 18 28 10Ω 100Ω 2 b 7 d c 1 17 1 - Flywheel c : alternative curr.
Trekker - Squab 4x 10w D 1,2w 5A 5 on off 6 3 1 4 12V 4Ah 21 20 19 16 2 15 2 - Ignition switch 15 - Battery 16 - 5A Fuse 19 - Turn signal relay 20 - Indicator control 21 - Indicator bulbs D - Indicator telltale 18 ELECT RIC EQUIPMENT 1. Key switch to OFF No display should appear on the multimeter .
Trekker - Squab 19 ELECT RIC EQUIPMENT 5/21w 12V 4Ah 5A 0,75 Ω 4w 5 on off 6 3 1 4 15 27 14 24 16 2 23 26 25 2 - Ignition switch 14 - Rear and stop light 15 - Battery 16 - 5A Fuse 23 - Stop contact .
Trekker - Squab a d b c b B 1,2w C 5/21w 12V 4Ah 4x 10w D 1,2w 1,2w E A 5 on off a 5A 5k Ω 5k Ω 5,9 Ω 30w 6,7 Ω 5w 0,75 Ω 4w 13 6 3 1 4 3 x 1,2w 15w 25 26 15 24 14 27 16 23 22 20 19 21 17 18.
Trekker - Squab a b b C 5/21w 12V 4Ah D 1,2w 1,2w E 22 25 24 5 on off a 5A 5,9 Ω 30w 6,7 Ω 5w 0,75 Ω 4w 35/35w 13 33 5w 6 3 1 4 B 1,2w 12 H L A 3 x 1,2w 4 3 7 9 11 28 18 17 19 20 21 10Ω 26 23 .
Trekker - Squab 22 * According to the model 2 2 A Instrument panel lighting B Headlamp telltale C Low oil level telltale D Indicator telltale E Fuel gauge receiver 1 Flywheel a ignition b sensor c alt.
Trekker - Squab Note 2 23.
Trekker - Squab PEUGEOT MOT OCYCLES RECOMMENDS 2 STROKE OIL - ESSO 2T SPECIAL ................. 1 LITRE ........ Ref. : 753752 - ESSO 2T SYNTHETIC ............ 1 LITRE ........ Ref. : 753759 TRANSMISSION CASE OIL - GEAR OIL GX-SAE 8OW-90 ... 2 LITRES .
N° 1 1.753784.00 recommends Dans un souci constant d'amélioration Peugeot Motocycles se réserve le droit de modifier , supprimer ou ajouter toute référence citée DC/PS/SH Imp.
An important point after buying a device Peugeot FB-0-1-2-4 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Peugeot FB-0-1-2-4 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Peugeot FB-0-1-2-4 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Peugeot FB-0-1-2-4 you will learn all the available features of the product, as well as information on its operation. The information that you get Peugeot FB-0-1-2-4 will certainly help you make a decision on the purchase.
If you already are a holder of Peugeot FB-0-1-2-4, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Peugeot FB-0-1-2-4.
However, one of the most important roles played by the user manual is to help in solving problems with Peugeot FB-0-1-2-4. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Peugeot FB-0-1-2-4 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
