

15” SIGNATURE SERIES 24” SIGNATURE SERIES 48” SIGNATURE SERIES C-SERIES ADA-COMPLIANT SERIES 18” SHALLOW-DEPTH SERIES

Form No. Z2348 Rev. 04.01.2014


This Warranty does not apply to:
Perlick will provide the parts and labor necessary to repair or replace (at Perlick’s option) any parts proven to be defective in material or workmanship during the Basic Warranty Period. Perlick will provide the replacement parts, but not the labor, for any parts of the hermetically sealed refrigeration system proven to be defective in materials or workmanship during the Extended Warranty Period. The cost of freight to ship the replacement parts will be paid by Perlick. Replacement parts are warranted for the remainder of the original warranty period, or ninety (90) days, whichever is longer.
Your Perlick product can be registered via the online Warranty Registration form at http://www.perlick com/residential-products/service-support/warranty- registration/.
This Warranty applies only to products installed in the fifty states of the United States, the District of Columbia and the ten provinces of Canada.
To obtain the warranty coverage described in this Warranty, Perlick or its authorized distributor or dealer must receive written notice of the warranty claim within the applicable warranty period. To receive parts and/or service and the name and telephone number of the nearest Perlick authorized service representative, please contact your Perlick dealer or distributor, or Perlick’s Customer Service Department by writing to it at Perlick Corporation, Attn: Customer Service Department, 8300 West Good Hope Road, Milwaukee, Wisconsin 53223; or by calling Perlick’s Customer Service Department at 800-558-5592; or by e-mailing Perlick’s Customer Service Department at warrantyserv@perlick.com. In addition, you can notify Perlick of a warranty claim by visiting Perlick’s website at http://www.perlick.com/residential-products/service- support/ and filling out and submitting the Technical Service Request form that appears there.
THIS LIMITED WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE; PROVIDED HOWEVER, THAT TO THE EXTENT REQUIRED BY LAW, IMPLIED WARRANTIES ARE INCLUDED BUT DO NOT EXTEND BEYOND THE DURATION OF THE EXPRESS WARRANTY FIRST SET ABOVE.
PERLICK’S SOLE LIABILITY AND YOUR EXCLUSIVE REMEDY UNDER THIS WARRANTY ARE SET FORTH IN THE PARAGRAPH ENTITLED “REMEDY” SET FORTH ABOVE.
PERLICK SHALL HAVE NO LIABILITY WHATSOEVER FOR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING FROM THE SALE, USE OR INSTALLATION OF THE PRODUCT OR FROM ANY OTHER CAUSES WHATSOEVER, WHETHER BASED ON WARRANTY (EXPRESS OR IMPLIED) OR OTHERWISE BASED ON CONTRACT, TORT OR ANY OTHER THEORY OF LIABILITY. IN NO EVENT SHALL PERLICK’S LIABILITY WITH RESPECT TO A PRODUCT EXCEED THE PURCHASE PRICE OF THE PRODUCT.
All service provided by Perlick under this Warranty must be performed by Perlick’s authorized service representatives, unless otherwise specified by Perlick in writing. Service will be provided during normal business hours.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you. This Warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
This Warranty applies only to the original retail purchaser of the Perlick product, and may not be assigned or transferred.

SAFETY PLEASE READ all instructions completely before attempting to install or operate the unit. Take particular note of the DANGER, WARNING and CAUTION information in the manual. The information is important for the safe and efficient installation, operation and care of your Perlick unit.
PLUMBING No plumbing connections are required. Condensate from the cooling coil is automatically evaporated through a condensate pan located in the condensing section of the unit.
ELECTRICAL A 115 volt, 60 Hz, 15 amp circuit breaker and electrical supply are required. A separate circuit is required for each Perlick unit installed.
Indicates a hazard that WILL result in serious injury or death if precautions are not followed.
Follow the National Electrical Code and any local codes or ordinances when installing the receptacle.
Indicates a hazard MAY cause serious injury or death if precautions are not followed.
All Perlick units come equipped with a NEMA 5-15P 90° plug with a 5’ cord extending beyond the rear of the cabinet. The electrical outlet must be flush with, or recessed into, the wall surface for all HP, HC and HA models. HH models have a recess at the rear of the cabinet to accomodate the plug and keep a true 18” depth.
Indicates a hazard where minor injury or product damage may occur if precautions are not followed.
PRIOR TO INSTALLATION Carefully inspect cabinet for hidden damage. If damage is discovered, file your claim immediately with the transport company. Perlick is not responsible for damage in transit.
Do not attempt to operate the equipment on any other power source than that listed on the Electrical Specification Plate attached to the unit.
When moving the unit, be sure to protect finished flooring with appropriate material to avoid damage from moving the unit.
Serious Electrocution Hazard! Electrical grounding is required. This appliance is equipped with a 3-prong (grounding) polarized plug for your protection against possible shock hazards. Failure to comply with these electrical guidelines may result in possible death or serious injury, fire, or loss of property.
Do not lift unit by drawer, shelving or door handles, as damage to the unit could occur if not moved as instructed.
To prevent personal injury, a minimum of two people are required to lift the unit. Larger units may require additional personnel.
Before moving the unit, secure the door shut with tape to prevent door from swinging open while being moved. Carefully move unit to installation site and place in front of opening.
If unit has been laid on its back or sides, place unit upright and allow minimum of 24 hours before connecting power.

INSTALLATION Unit may tip forward if loaded racks/shelves are all pulled out at the same time. To prevent tipping, and to provide stable installation, the unit must be secured in place with the anti-tip brackets supplied with the unit. The anti-tip brackets, when properly installed, should secure the rear legs/glides to the mounting surface and prevent the unit from tipping forward.
A set of anti-tip brackets is supplied with the unit. These brackets should be attached to the floor at the rear of the unit. Each bracket must be located to engage the rear glides when the cabinet is pushed back into position. Refer to Figures 1, 2 and 3 (shown below) for anti-tip bracket mounting locations.


Figure 1. 15” Anti-tip Kit Figure 2. 24” Anti-tip Kit

22-1/32” 23-3/16” 1-3/4” 5/16”
1/2“ to hole 3/16”
Figure 3. 48” Anti-tip Kit

2). Check that the following are level and square: • Front and interior opening
If the unit is to be installed under a countertop, it is recommended that the countertop be supported by a structure other than the unit itself to prevent damage to the unit.
Make sure the floor under the unit is level with the surrounding finished floor. Protect a finished floor with plywood, cardboard, or some other suitable material before moving the unit into place. Failure to do this may result in damage to the floor.
To prevent possible damage to the countertop, do not place heavy objects on countertop directly over unit. INSTALLING THE UNIT 1). Plug the unit into the 15 amp grounded electrical outlet located within the installation opening. With power applied to the unit, check that the lighting and cooling functions operate properly. Turn off the power to the wall outlet at the circuit breaker.
1). Make sure the space opening is correctly sized for the unit. See chart below for finished rough opening requirements:

2). With all surfaces in the installation opening square and level, refer to Figure 4 on page 7 and perform the following steps to level the unit:
3). Slide the unit into position in the opening. Make sure the rear leveling legs slide under the ant-tip brackets. Push the unit into the opening until the bottom front edge of the unit is flush with the surrounding cabinetry, or until the rear legs are tight against the anti-tip brackets.
4). Shim the front of the unit so the front face is flush with the surrounding cabinetry. Adjust the front legs to support the countertop at the shimmed height. Using an adjustable wrench or pliers, turn the legs clockwise to lower the unit or counterclockwise to raise it. Countertop should be resting on top of the unit.

TOE PLATE INSTALLATION Once the unit is secured in place, install the louvered toe plate. Secure the plate by snapping the latch into the latch catch on the unit (Figure 5).
The toe plate must be removed to service the unit. The floor cannot interfere with removal, and the louvered sections must not be covered or obstructed. Obstructions could prevent proper air circulation, which may damage the unit.
Measure front of opening from floor surface to bottom edge of countertop
Measure at both rear corners of unit from floor surface to bottom of countertop
Latch Figure 4. Leveling the Unit
Figure 5. Toe Plate Installation
5). Check interior door openings to make sure the unit is level and square. Install shelving and/or drawers. Place the slide brackets squarely into the bracket grooves. When installed properly, a “click” should be heard from the slide bracket retaining tabs and the brackets should slide smoothly. The retaining tabs will stop the shelf/drawer when pulled out to full extension.
6). Turn on the power to the wall outlet at the circuit breaker.
Latch Strike

DOOR OPTIONS Perlick residential units offer a variety of door panel design alternatives; solid stainless steel, solid wood overlay, glass with stainless steel trim and glass with wood overlay trim.
Completely empty shelf or drawer before removing.
Solid stainless steel and stainless steel glass doors are shipped from the factory with decorative stainless steel panels and handles in place on the unit. Solid wood overlay and glass wood overlay doors are designed to accept a decorative front panel to match surrounding cabinetry and door handles.
All Perlick units (excluding beer dispenser and ice maker models) accept any of the above door configurations and are fully interchangeable. Glass door configurations are not available on beer dispenser or ice maker models.

CHANGING DOOR SWING DIRECTION NOTE: Changing the door mount is not advisable if the door is equipped with a custom wood overlay. Doing so may result in an undesirable handle position.
Lift one tab on extender UP while pushing tab on opposite extender DOWN and pull out to remove.
To change the door swing direction, a hinge kit is required:
In addition to the hinge kit, the following tools are required:
To remove brackets, remove shelf, lift front of bracket to disengage the front key slot, then pull forward to disengage the rear key slot.
1). Support the door in the open position as shown in Fig. 7 on page 9. Remove the hinge pin.
2.) Pull door to the side and then lower door.
3.) Remove top and bottom hinge brackets. Retain screws for later use. See Fig. 8 on page 9.
4). Remove the hole plugs from the top and bottom hinge bracket mounting holes (see Fig. 8 on page 9). Place the plugs in the holes on the opposite side made vacant by removing the hinges in step 3.
Figure 5. Shelving/Drawer Adjustment

5). Using the screws removed in step 3, install the top and bottom hinge brackets from the kit (Fig. 9).
Hinge brackets and mounting screws
Pull door to the side then lower door
Figure 7. Door Removal
Hinge brackets and mounting screws
Figure 9. Hinge Installation
6). Remove the top and bottom door hinge brackets and the push plunger brackets (Fig. 10). Retain the screws for later use.
Hinge brackets and mounting screws
Hinge brackets and mounting screws
Hinge brackets and mounting screws
Figure 10. Door Brackets
Figure 8. Hinge Removal
Remove hinge pin · Hole plugs

7). Remove the front panel from the door assembly by removing the inner mounting screws, 4 per side, from the perimeter of the door assembly (Fig. 11). Rotate the front panel 180°. The top becomes the bottom. Reattach using the same screws and mounting holes.
9). Insert the bearing into the door hinge bracket (Fig. 13).
10). Insert the V-block into the door bottom hinge bracket and attach with the e-clip (Fig. 13). Note the orientation of the V-block.
Bearing in door top hinge bracket
Figure 13. Bearing and V-Block
Corner screws need not be removed to remove front panel
11). Attach the top and bottom hinges and push plunger using screws removed in step 6 (Fig. 14).
Figure 11. Removing Front Panel
8). Remove the Perlick nameplate from the door front using a plastic putty knife (Fig. 12). Install the new Perlick nameplate included in the kit.
Top hinge and screws
Bottom hinge and screws
Figure 14. Door Hinges
Figure 12. Nameplate

12). Place the lower V-block into the lower cabinet hinge with the notch parallel to the cabinet (Fig. 15).
The handle mounting on the wood overlay should be mounted on the overlay only (not the actual door) to avoid damage to the factory door.
Proper woodworking materials and equipment should be used to avoid damage or errors in workmanship.
V-block parallel to cabinet
DOOR LOCK INSTALLATION NOTE: Full size lock installation wood overlay panel templates are available on the Perlick website. Visit www.perlick.com/ Residential, click on Service & Support, and then choose Wood Overlay Templates from the menu. Lock templates are available for all HP, HC, HA and HH series models. Take care in choosing the correct template for your specific model.
Figure 15. Installing V-Block
13). Lift the door assembly and insert the top pin into the bearing. Move door toward cabinet and align the V-blocks (Fig. 16).
When installing to a wood overlay, perform the lock installation before mounting the wood overlay to the door!
Insert top pin into bearing
Insert and tighten hinge pin
Figure 16. Installing Door
14). Insert and tighten the lower hinge pin to complete the assembly.
Figure 17. Installing Door Lock

WOOD OVERLAY INSTALLATION (FOR -2 AND -4 MODELS) Before beginning installation, check all components for proper fit and finish.
WINE RACK TRIM (OPTIONAL) All wine reserve racks come with sleek stainless steel fronts. Unfinished solid hardwood fronts are optional and can be removed and replaced with other wood to match your cabinetry. See Figure 18 and 19 for wine rack face details.

Scan the QR code to the right with your smart phone to watch a detailed how-to video on installing a wood overlay panel onto Perlick doors. Otherwise, follow these written instructions.
NOTE: The unfinished faces should be finished and sealed. In many cases, stains and/or finishes have odors that may be objectionable in an enclosed area. Do not stain or finish wood faces while installed on unit. To remove the front wood face from the wine shelf, simply pull out the wine shelf and remove the fasteners, finish as desired, and when completely dry, reinstall with fasteners.
All overlay doors require a trim panel of at least 3/4” thick. The solid wood and glass wood panels should not weigh more than 10 lbs.

Do not overtighten wood overlay attachment screws, as this may damage the factory supplied door frame.


Use and Care Guides, Specification Sheets, Wood Overlay Templates for Doors, Drawers and
Grilles, and Corresponding Compliance and Energy Guides are available for download at
www.perlick.com/residential-products/service-support.
800.558.5592.
Customer Service and Technical Service are available business days
Monday through Friday from 8 a.m. to 4:30 p.m. CST.
Form No. Z2348 Rev. 04.01.2014
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.