Instruction/ maintenance manual of the product High Performance Pump Pentair
Go to page of 20
IMPOR T ANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SA VE THESE INSTRUCTIONS Installation and User's Guide SuperFlo ™ High Performance Pump.
© 2005 Pentair W ater Pool and Spa, Inc. All rights reserved. This document is subject to change without notice. 1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-8000 10951 West Los Angeles A ve., Moorpark, CA 93021 • (805) 523-2400 T rademarks and Disclaimers : SuperFlo is a trademark of Pentair W ater Pool and Spa, Inc.
i SuperFlo Pump Installation and User ’ s Guide T able of Contents Important Safety Precautions .............................................................................................. i i Section 1: Introduction ..............................
ii SuperFlo Pump Installation and User ’ s Guide IMPORTANT SAFETY PRECAUTIONS Consumer Information and Safety The SuperFlo pumps are designed and manufactured to provide many years of safe and relia.
iii SuperFlo Pump Installation and User ’ s Guide IMPORTANT SAFETY PRECAUTIONS (continued) W ARNING — Do not operate the pump until you have read and understand clearly all the operating instructions and warning messages for all equipment that is a part of the pool circulating system.
iv SuperFlo Pump Installation and User ’ s Guide.
1 SuperFlo Pump Installation and User ’ s Guide Section 1 Introduction SuperFlo ™ High Performance Pump Overview The perfect choice for all types of pools, the SuperFlo was specifically designed to be your best choice for a variety of inground pools.
2 SuperFlo Pump Installation and User ’ s Guide General Features • Extremely quiet operation • Unionized fittings (1.5" and 2") for simple replacement • Cam and Ramp™ lid for easy .
3 SuperFlo Pump Installation and User ’ s Guide Section 2 Electrical Requirements This section describes how to wire the SuperFlo pump. Note: Before installing this product, read and follow all warning notices and instructions starting on page ii. Electrical Requirements and Wiring When pump is mounted permanently within 5 ft.
4 SuperFlo Pump Installation and User ’ s Guide Wiring Installation, cont.’d. 6. Permanently ground the motor using the green ground terminal located on the inside of the motor canopy or access plate, see Figure 1 . Use the correct wire size and type specified by National Electrical Code.
5 SuperFlo Pump Installation and User ’ s Guide Section 3 Maintenance This section describes how to maintain the SuperFlo pump. Cleaning the Pump Strainer Basket W ARNING — DO NOT open the strainer pot if pump fails to prime or if pump has been operating without water in the strainer pot.
6 SuperFlo Pump Installation and User ’ s Guide Cleaning the Pump Strainer Basket, cont’d. 9. Reinstall the lid by placing the clamp and the lid on the pot; see Figure 3 . a . Make sure the lid O-ring is properly placed. Seat the clamp and lid then turn clockwise until the handles are horizontal; see Figure 4 .
7 SuperFlo Pump Installation and User ’ s Guide Section 4 Servicing W ARNING — Risk of electrical shock or electrocution. This pool pump must be installed by a licensed or certified electrician or a qualified pool serviceman in accordance with the National Electrical Code and all applicable local codes and ordinances.
8 SuperFlo Pump Installation and User ’ s Guide Pump Disassembly , cont’d. h. To unscrew the impeller from the shaft, twist the impeller counter-clockwise. i . Remove the four bolts from the seal plate to the motor using a 3/8 inch wrench. j . Place the seal plate face down on a flat surface and tap out the ceramic seal.
9 SuperFlo Pump Installation and User ’ s Guide Section 5 Restart Instructions If the SuperFlo pump is installed below the water level of the pool, close return and suction lines prior to opening hair and lint pot on pump. Make sure to reopen valves prior to operating.
10 SuperFlo Pump Installation and User ’ s Guide Section 6 T roubleshooting Use the following troubleshooting information to resolve possible problems with your SuperFlo pump.
11 SuperFlo Pump Installation and User ’ s Guide Section 7 T echnical Data Illustrated Parts Item Part Description No. No. Item Part Description No. No. 1 075236 M OT OR SQ FL, 2 HPF , 2.5 A, 1 PHASE, 60 Hz, STD, 230V — (Almond) 1 075235 M OT OR SQ FL, 1.
12 SuperFlo Pump Installation and User ’ s Guide SAVE THESE INSTRUCTIONS Pump Curve PENT AIR POOL PRODUCTS, INC. PUMP PERFORMANCE CUR VE SUPERFLO ™ SERIES 0.00 10.00 20.00 30.00 40.00 50.00 60.00 70.00 80.00 90.00 100.00 0.0 20.0 40.0 60.0 80.0 100.
SF NOTES.
P/N 350096 Rev . B November 2, 2005.
An important point after buying a device Pentair High Performance Pump (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pentair High Performance Pump yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pentair High Performance Pump - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pentair High Performance Pump you will learn all the available features of the product, as well as information on its operation. The information that you get Pentair High Performance Pump will certainly help you make a decision on the purchase.
If you already are a holder of Pentair High Performance Pump, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pentair High Performance Pump.
However, one of the most important roles played by the user manual is to help in solving problems with Pentair High Performance Pump. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pentair High Performance Pump along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
