Instruction/ maintenance manual of the product PMCQ14A Pelco
Go to page of 16
PMCQ14A 14-Inch Color Quad Monitor Installation/ Operation Manual C1970M-A (7/01) Pelco • 3500 Pelco Way, Clovis • CA 93612-5699 USA • www.pelco.
2 Pelco Manual C1970M-A (7/01) CONTENTS Section Page IMPORT ANT SAFEGUARDS AND WARNINGS ................................................................ 3 DESCRIPTION ....................................................................................
Pelco Manual C1970M-A (7/01) 3 IMPOR T ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel and conform to all local codes.
4 Pelco Manual C1970M-A (7/01) DESCRIPTION FEA TURES • Observe up to Four Camera Images at Once or in Sequence • Programmable Dwell T ime for Each Camera During Sequence Mode • Picture-In-Pictur.
Pelco Manual C1970M-A (7/01) 5 Figure 1. T ypical Application Using PMCQ14A Monitor EH3500 IMAGEP AK OUTDOOR W/ HEA TER & DEFROSTER WCS1-4 POWER SUPPL Y EH100 IMAGEP AK INDOOR MCS4-2 POWER SUPPL Y.
6 Pelco Manual C1970M-A (7/01) INST ALLA TION 1. Place monitor on a stable surface such as a shelf or desk top. 2. Connect cameras or alternate video sources to the desired channel IN/OUT connectors on the back of the monitor (refer to Figure 3). 3. Set impedance switches to the 75-ohm position (refer to Figure 3).
Pelco Manual C1970M-A (7/01) 7 PROGRAMMING QUAD MENU CH4 VCR PIP SEQ CH3 ZOOM FREEZE CH2 RESET ALT CH1 TALK AUDIO MIC TINT SHARP COLOR BRIGHT CONTRAST VOLUME POWER FRONT P ANEL PROGRAMING BUTTONS RETURNS TO DEF AUL T (AL T+MENU ENTERS/EXITS SETUP MENU) Figure 4.
8 Pelco Manual C1970M-A (7/01) CHECK OUT T able B. Check-Out Procedure This procedure assumes that power is on. Step Procedure Results 1 Calibrate cameras. Follow the manufacturer ’ s recommendations for calibration. 2 Press the QUAD/MENU button. See quad display .
Pelco Manual C1970M-A (7/01) 9 Figure 5. Display Selections PIP MODE (HORZ) QUAD MODE SEQUENCE MODE PIP SEQ QUAD MENU SINGLE-CAMERA MODE CH4 VCR MENU MODE CH4 VCR CH3 ZOOM FREEZE CH2 CH1 T ALK AUDIO M.
10 Pelco Manual C1970M-A (7/01) INTERCOM The intercom operates with one camera at a time. When the monitor is in quad display mode, a speaker icon appears next to the channel number to show which camera has the intercom active. NOTE: The intercom function is available only when CCQ1400A-4 cameras are used.
Pelco Manual C1970M-A (7/01) 11 ALARM The alarm operates with any or all cameras at once. ALM flashes at the top center of the screen and the display automatically switches to show the camera that has the alarm. Figure 7. Alarm Activities on Screen T able E.
12 Pelco Manual C1970M-A (7/01) Figure 8. Monitor Back Panel Controls and Connections T able F . Back Panel Reference Key Reference Number Description Function 1 Power inlet Accepts 1 10 to 240 V olts AC, 50/60 Hz power. 2 Main power switch Controls power to monitor and cameras.
Pelco Manual C1970M-A (7/01) 13 Figure 9. Monitor Controls T able G. Front Panel Reference Key Reference Number Description Function 1 Reset/AL T key Resets alarm or video loss detection. When there is no alarm, use as AL T key to activate the alternate functions of the Zoom, PIP , Quad, CH4, and T alk keys.
14 Pelco Manual C1970M-A (7/01) TECHNICAL SPECIFICA TIONS ELECTRICAL Input Voltage: 100 to 240 VAC, 50/60 Hz Power Consumption: 70 watts Signal Format: NTSC Scanning System: 2:1 interlace Picture Elements: 512 (H) x 492 (V) Horizontal Resolution: 350 TV lines (center) Linearity: Less than 12% Audio Output: 1.
Pelco Manual C1970M-A (7/01) 15 ENVIRONMENTAL Operating Temperature: 32 ° to 104 ° F (0 ° to 40 ° C) Storage Temperature: 4 ° to 158 ° F (-20 ° to 70 ° C) Humidity: 35% to 80%, non-condensing (Design and product specifications subject to change without notice.
16 Pelco Manual C1970M-A (7/01) REVISION HISTOR Y Manual # Date Comments C1970M 7/00 Original version. C1970M-A 7/01 Date and time programming revised. P elco , the P elco logo, Camclosure, Esprit, Genex, Legacy , and Spectr a are registered trademarks of P elco .
An important point after buying a device Pelco PMCQ14A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco PMCQ14A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco PMCQ14A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco PMCQ14A you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco PMCQ14A will certainly help you make a decision on the purchase.
If you already are a holder of Pelco PMCQ14A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco PMCQ14A.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco PMCQ14A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco PMCQ14A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
