Instruction/ maintenance manual of the product HB6000/220 Pelco
Go to page of 8
® HB6000, HB6000/220, and HB6024 Heater/Blower Kits Installation/Operation Manual C496M (12/90) 1.0 W ARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by Qualified Service Personnel and conform to all Local codes.
2 Pelco Manual C496M (12/90) 3.1 MODELS HB6000 120 VAC thermostatically controlled heater and blower. Heater provides 80 watts of heat and activates ON at 40 ° F (4.44 ° C) and OFF at 60 ° F (15.56 ° C). Blower provides internal air circulation (12 cfm at 4 watts) and activates ON at 110 ° F (43.
Pelco Manual C496M (12/90) 3 3.4 POWER REQUIREMENTS The blower and heater require a 24 V AC/120 V AC/230 V AC, 50/60 Hz single phase power source. They use the following wattage when in operation. Blower: 4.5 watts Heater: 80 watts 4.0 INST ALLA TION T o install the HB6000, HB6000/220, and HB6024 per- form the following steps.
4 Pelco Manual C496M (12/90) 4.3 HEA TER/BLOWER WIRING The blower is factory wired to the PCB assembly . Connect the heaters to the PCB assembly as shown in the respective wiring diagrams (refer to Figure 2, Fig- ure 3, or Figure 4). Supply AC line voltage (230 V AC, 120 V AC, or 24 V AC) as shown.
Pelco Manual C496M (12/90) 5 Figure 3. HB6000 Heater/Blower Kit Wiring Diagram (120V AC) Figure 4. HB6024 Heater/Blower Kit Wiring Diagram (24 V AC).
6 Pelco Manual C496M (12/90) 5.0 MECHANICAL P ARTS LIST FOR HB6000/220 (230 V AC) HEA TER/BLOWER KIT Item No. Qty Description Part Number 1 1 Bracket, Fan/PCB, HB6000 HB60004000COMP 2 1 PCB Assembly , T erm/Thermo, EH4500 Series PCB9000256ASSY 3 1 Fan 10CFM 2.
Pelco Manual C496M (12/90) 7 6.0 SPECIFICA TIONS ELECTRICAL Input Voltage: 2 4 VAC/120 VAC/230 VAC, 50/60 Hz Electrical Connection: One 10-position terminal block (in- put) One 6-pin lens connector Tw.
8 Pelco Manual C496M (12/90) 7.0 WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products.
An important point after buying a device Pelco HB6000/220 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco HB6000/220 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco HB6000/220 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco HB6000/220 you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco HB6000/220 will certainly help you make a decision on the purchase.
If you already are a holder of Pelco HB6000/220, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco HB6000/220.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco HB6000/220. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco HB6000/220 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
