Instruction/ maintenance manual of the product FR82041 Pelco
Go to page of 28
® INST ALLA TION F T82041/FR82041 Unmanaged Ethernet Switch Four 10BASE-T/100BASE-TX Ports and One 100BASE-FX Fiber Port C2623M (2/07).
.
C2623M (2/0 7) 3 Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Regulatory Not ices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 C2623M (2/07) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any ventilation openings.
C2623M (2/0 7) 5 The product and/or manual may bear the following marks: This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.
6 C2623M (2/07) Regulatory Notices This device complies with Part 15 of the FCC Rule s. Operation is subject to the following two conditions: (1) this device may not cause harmful in terference, and (2) this device must accept any interference received, including interfer ence that may cause undesired operation.
C2623M (2/0 7) 7 Product Overview DESCRIPTION The F T82041/FR82041 unmanag ed Ethernet switch provid es four 10BASE-T/100BASE-TX ports and one 100BASE-FX fiber port for the trans port of bidirectional Ethernet data.
8 C2623M (2/07) • Designed to meet NEMA TS 2 and Caltrans traff ic signal control equipment standards for ambient operating temperature, mechanical shock and vibrati on, humidity with condensation, .
C2623M (2/0 7) 9 OPTIONAL ACCESSORIES The following optional a ccessories are available: WM5001-3U Wall mount base ki t for single-width module WM5001-3UEXP Wall mount expansion kit for single-width m.
10 C2623M (2/07) REAR PANEL Figure 3 illustrates the rear pa nel of the F T82041 and FR82041 modules. Figure 3. Rear Panel of F T82041 and FR82041 Mo dules (SC Fiber Connector Shown) For additional information about r ear -panel connections, refer to Installation on page 11.
C2623M (2/0 7) 11 Installation PACKAGE CONTENTS The following it ems are supplied: 1 F T82041 or FR82041 module 1 Regulated switching power suppl y with four plug adapt ers (North American, Australian, U.K., and European configurations); 100-240 V A C, 50-60 Hz input, 12 VDC output 1 Wall clip with two 4-40 x 0.
12 C2623M (2/07) Using the TX Mode switch for a parti cular port, y ou can do the following: • Enable autonegotiation or select (force) a specific data rate and duplex mode: – Enabling autonegotia.
C2623M (2/0 7) 13 NOTE: TX Mode configuration must be set when the module is powered off. If you wish to change a TX Mode switch setting after the module has been powered on, power of f the module, change the TX Mode switch setting, and then power on the module again.
14 C2623M (2/07) Mounting the F T82041/FR82041 Module Using the Wall Clip NOTE: Before mounting the F T82041/FR82041 module to a wall, ensure that there is adequate space at both ends for viewing the fr ont-panel LEDs and for making the various rear-pa nel cable connec- tions.
C2623M (2/0 7) 15 CONNECTIONS Connections to the F T82041/FR82041 module are made on the rear panel of the unit (refer to Figure 6). Figure 6. F T82041/FR82041 Module Connecti ons As illustrated in Fi.
16 C2623M (2/07) • Fiber connection NOTE: Fiber port A of the F T82041 module connects to fiber port B of the FR82041 module or of any other Pelco Ethernet sw itch that supports wavelength division multiplexing (WDM).
C2623M (2/0 7) 17 T roubleshooting LED indicators on the front and rear panels of the F T82041/FR82041 module allow you to monitor operational status: • LED indicators on the front panel allow you to monitor operating power , 100BASE-FX port status, and optic signal/l aser status.
18 C2623M (2/07) Optic Fault LED ( ) Green The optical signal is being received and laser is operating properly . — No action is required. Red The optical signal is not being received. Remote module is not powered on. Check power connections. Replace power supply if necessary .
C2623M (2/0 7) 19 T able C. T roubleshooting with Rear -Panel Indicators Indicator Color Meaning Possibl e Cause Corrective Action RJ-45 10BASE-T/100BASE-TX Port Stat us LED - Left (Link / Activity) Amber A 10BASE-T link is established. — If 10BASE-T operation is desired, no action is required.
20 C2623M (2/07) RJ-45 10BASE-T/100BASE-TX Port Status LED - Left (Link/Activity) (Continued) Not lit A 10BASE-T or 100BASE-TX link cannot be estab- lished. A problem may exist with the cable: • Cable is not connected to the module or to the 10BASE-T/100BASE-TX compatible device.
C2623M (2/0 7) 21 RJ-45 10BASE-T/100BASE-TX Port St atus LED - Right (Duplex/Collision) Amber Port is set to 10BASE-T full- duplex mode. — If 10BASE-T full-duplex opera- tion is desired, no action is required.
22 C2623M (2/07) RJ-45 10BASE-T/100BASE-TX Port Status LED - Right (Duplex/Co llision) (Continued) Green Port is set to 100BASE-TX full- duplex mode. — If 100BASE-TX full-duplex operation is desired, no action is required.
C2623M (2/0 7) 23 RJ-45 10BASE-T/100BASE-TX Port Status LED - Right (Duplex/Co llision) (Continued) Not lit Port is set to 10BASE-T half- duplex mode and no collisions are detected.* — If 10BASE-T half-duplex operation is desired, no action is required.
24 C2623M (2/07) Specifications PERFORMANCE Switch T ype Unmanaged Layer 2 Switch Method Store and forward Switch Fabric Non-head-of-line blocking Data Rate 10/100 Mbps Compliance IEEE 802.
C2623M (2/0 7) 25 OPTICAL POWER BUDGET AND MAXI MUM TRANSMISSION DIST ANCE Model Number Wavelength (T ransmit/Receive)* Optical Power Budget Maximum T ransmission Distance T ransmitter End Receiver End Fiber Port A Fiber Port B Multimode (62.5/125 μm) F T82041MSTR-1 FR82041MSTR-1 1310/850 nm 850/1310 nm 26 dB † 2 km (1.
26 C2623M (2/07) Appendix. RJ-45 Connector Pinouts Figure 7 illustrates RJ-45 MDI/MDI-X connector pinouts. Figure 7. RJ-45 MDI/MDI-X Connector Pinouts T able D summarizes RJ-45 MDI/MDI-X connector pinouts.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merc handise pr oved defective in mate rial or work manship for a period of one year after the date of shipment.
® Worl dwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .
An important point after buying a device Pelco FR82041 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco FR82041 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco FR82041 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco FR82041 you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco FR82041 will certainly help you make a decision on the purchase.
If you already are a holder of Pelco FR82041, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco FR82041.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco FR82041. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco FR82041 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
