Instruction/ maintenance manual of the product C916M Pelco
Go to page of 12
AUX2000 Auxiliary Control Box Installation/ Operation Manual C916M (11/90) ® Pelco • 3500 Pelco Way, Clovis, CA 93612-5699 • USAwww.pelco.com In North America and Canada: Tel (800) 289-9100 • F.
12 P elco Manual C916M (11/90) ®Pelco and the Pelco logo are registered trademarks of Pelco. ©Copyright 1990, Pelco. All rights reserved. ii T ABLE OF CONTENTS Section Page 1.0 W ARNINGS ..............................................................
P elco Manual C916M (11/90) 1 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 4 . Only use replacement parts recommended by Pelco.
2 P elco Manual C916M (11/90) 2.0 SCOPE The information contained within this manual covers the installation and operation of the AUX2000. 3.0 DESCRIPTION The AUX2000 is an auxiliary control box for the Coaxitron ® and W iretron receiver/drivers.
P elco Manual C916M (11/90) 3 4.0 INST ALLA TION Refer to the following instructions when installing the AUX2000 auxiliary control box for the Coaxitron ® and W iretron receiver/drivers. 1. Determine the location for the AUX2000 auxiliary control box for the Coaxitron ® or W iretron receiver/ drivers.
4 P elco Manual C916M (11/90) 4. The contact pins supplied with the mating connec- tor are the “crimp” type which may also be sol- dered if you so desired (item 4). 5. After crimping or soldering the contact pins to the conductors, push them into the proper holes in the connector until they snap in place.
P elco Manual C916M (11/90) 5 5.0 OPERA TION The AUX2000 is operated by the Coaxitron ® or W iretron controller . 5.1 SYSTEM TEST Using the systems controller , verify that the auxiliary devices function.
6 P elco Manual C916M (11/90) 7.0 AUX2000 MECHANICAL P ARTS LIST Description Part Number Enclosure DS100JA4000COMP Fuse holder FUS357001 T erminal Strip TRS20007 Strain Relief EH5510043 Mating Connector (Sockets) CONA37S Mating Connector (Pins) CONA37P 8.
P elco Manual C916M (11/90) 7 Figure 3. A UX2000 Schematics P/T COMMON MANUAL IRIS LEFT DOWN UP RIGHT GROUND CAMERA AC (HIGH) IRIS FOCUS ZOOM LENS COMMON CAMERA AC (LOW) COMMON AUX 1 AUX 2 AUX 3 1 2 3.
8 P elco Manual C916M (11/90) 10.0 SPECIFICA TIONS MECHANICAL Enclosure: UL listed gray industrial control panel enclosure Weatherproofing: Cover and connectors fully gasketed Mounting Means: 6 - 0.31" (.79 cm) diameter holes Dimensions: 11.31" H x 9.
P elco Manual C916M (11/90) 9 NOTES.
11.0 WARRANTY AND RETURN INFORMA TION Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. Endura and ExSite are trademarks of Pelco.
An important point after buying a device Pelco C916M (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco C916M yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco C916M - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco C916M you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco C916M will certainly help you make a decision on the purchase.
If you already are a holder of Pelco C916M, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco C916M.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco C916M. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco C916M along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center