Instruction/ maintenance manual of the product C581M-B Pelco
Go to page of 40
Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150 International Customers: Tel (1-559) 292-1981 or FAX (1-5.
2 Pelco Manual C581M-B (1/04).
Pelco Manual C581M-B (1/04) 3 CONTENTS Section Page IMPORT ANT SAFEGUARDS AND WARNINGS ................................................................ 4 REGULA TORY NOTICES .............................................................................
4 Pelco Manual C581M-B (1/04) IMPOR T ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following W ARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel and conform to all local codes.
Pelco Manual C581M-B (1/04) 5 DESCRIPTION The KBD4002 Genex ® Multiplexer Keyboard is a full-function keyboard controller for the Genex MX4000 Multiplexer and the Genex MX4000SVR Multiplexer Server . This manual covers the KBD4002 keyboard’s operation with the duplex and simplex models of the multiplexer .
6 Pelco Manual C581M-B (1/04) INST ALLA TION The following parts are supplied: 1 KBD4002 keyboard 1 25-foot (7.6 m) data cable There are two modes of operation–multiplexer mode and multiplexer server mode–depending on whether the keyboard is connected to a multiplexer or to a server .
Pelco Manual C581M-B (1/04) 7 3. Replace the cover on the back of the keyboard. 4. A 25-foot (7.6 m) data cable with RJ-45 connectors is supplied with the keyboard. Plug one end of the cable into the back of the keyboard and plug the other end into the COM IN connector on the back of the multiplexer .
8 Pelco Manual C581M-B (1/04) Set switch 7 ON if you want to address all cameras consecutively . Set switch 7 OFF if you want to address cameras according to the multiplexer they are connected to. PROGRAMMING MODE Set switch 8 ON to program the server and the multiplexer .
Pelco Manual C581M-B (1/04) 9 2. If you have more than one multiplexer , each one must have its own address (Unit ID in the Advanced System Setup menu).
10 Pelco Manual C581M-B (1/04) 1. LED DISPLA Y Displays the address of the multiplexer (from 1-16) with which the keyboard is communicating. 2. LIVE/VCR KEY Selects the source of video to display on the monitor(s). LIVE is live video from the cameras.
Pelco Manual C581M-B (1/04) 11 T able B. Operation Guide NOTE: References to switch 7 in this table refer to the switch behind the panel on the back of the keyboard.
12 Pelco Manual C581M-B (1/04) T able B. Operation Guide (Continued) 1. Go to the Advanced System Setup menu. 2. Press the pan/tilt keys so the cursor highlights SPOT MONITOR DISPLA Y items. 3. Press the OPEN key until TRACK MAIN is displayed. 4. Exit the Advanced System Setup menu.
Pelco Manual C581M-B (1/04) 13 T able B. Operation Guide (Continued) 1. Press the MAIN MONITOR key . The green LED over the MAIN key lights. 2. Select the camera that you want to display full size.
14 Pelco Manual C581M-B (1/04) T able B. Operation Guide (Continued) 1. Press the MAIN MONITOR key . The green LED over the MAIN key lights. 2. Select a camera on the multiplexer that you want to sequence.
Pelco Manual C581M-B (1/04) 15 1. Select the desired multi-camera display . 2. Press and hold the multi-camera display key to enter the multi-screen programming mode.
16 Pelco Manual C581M-B (1/04) 1. Press the MAIN or SPOT MONIT OR key . The green LED over the MAIN or SPOT key lights. When using the MAIN MONITOR, the SPOT MONITOR DISPLA Y menu item in the Advanced System Setup menu must be set to TRACK MAIN (refer to the Advanced System Setup section).
Pelco Manual C581M-B (1/04) 17 1. Press the SPOT MONITOR key . The green LED over the SPOT key lights. 2. Select the camera. Addressing by Multiplexer (Switch 7 OFF) a.
18 Pelco Manual C581M-B (1/04) OPERA TION KEYBOARD COMMAND RESUL T T able B. Operation Guide (Continued) 1. Press the SPOT MONITOR key . The green LED over the SPOT key lights.
Pelco Manual C581M-B (1/04) 19 PROGRAMMING This section applies only to programming the multiplexer . T o program the multiplexer server , refer to the server manual. Programming allows you to configure the multiplexer from the KBD4002 for the way that you want your system to operate.
20 Pelco Manual C581M-B (1/04) P ASSWORD Y ou can program the multiplexer to request a password for access to programming menus. The password is enabled in the Advanced System Setup menu (refer to the Advanced System Setup section). The universal password is 3916 and cannot be changed.
Pelco Manual C581M-B (1/04) 21 Title Display (Duplex Multiplexer) ON - Displays camera titles and the word LIVE or VCR on the main monitor . OFF - Camera titles and the word LIVE or VCR are not shown on the main monitor . Title Display (Simplex Multiplexer) ON - Displays camera titles on the main monitor .
22 Pelco Manual C581M-B (1/04) ADV ANCED SYSTEM SETUP (View Key) To program the advanced main system parameters: 1. Press the MAIN MONITOR key . 2. Use the number keypad to enter the address of the multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key .
Pelco Manual C581M-B (1/04) 23 Spot Monitor Display If you want the spot monitor to switch to cameras that have alarms or activity detection, select BLANK, SEQUENCE, or TRACK MAIN, then under RESPONDS T O select ALARMS, ACTIVITY , or ALARMS/ACTIVITY .
24 Pelco Manual C581M-B (1/04) Relay Output Operates the relay on the back of the multiplexer . The relay is used to change the VCR to its alarm recording speed. In the alarms mode, an alarm signal is produced when a remote switch opens or closes a ground in the multiplexer; for example, if a switch is on a door and the door is opened.
Pelco Manual C581M-B (1/04) 25 Figure 5. Basic VCR Setting Menu T able D. VCR T ypes NTSC P AL UNIVERSAL UNIVERSAL GYYR TLC1800 ASUT A TL VCR 251 GYYR 2100 ASUTSA TL VCR 964 GYYR 2100 HD MODE BURLE TC.
26 Pelco Manual C581M-B (1/04) 5. When you have completed all the changes you want to make, go to EXIT . 6. Press the OPEN key to exit the programming mode. When HELP is highlighted, you may press the OPEN key to display a help screen that will tell you which keys to press to configure specific options.
Pelco Manual C581M-B (1/04) 27 CAMERA SETUP (Number and CAM Keys) To program a camera input: 1. Press the MAIN MONITOR key . 2. Select the camera. Addressing by Multiplexer (Switch 7 OFF) a.
28 Pelco Manual C581M-B (1/04) Coaxitron Format EXTENDED - Use when your system has moveable cameras controlled by 32-bit Coaxitron receivers, such as Esprit, Intercept, Spectra, and LRD41C21/LRD41C22 Series. OFF - Use when your system has fixed cameras only .
Pelco Manual C581M-B (1/04) 29 ACTIVITY DETECTION MASK SETUP Activity detection continually monitors selected camera inputs for motion. When motion is detected, the multiplexer increases the frequency with which that camera(s) is shown and recorded. Activity detection is most ef fective when only a few cameras are showing activity .
30 Pelco Manual C581M-B (1/04) 7. T urn activity boxes on or off (by default, all activity boxes are on). To turn on all activity boxes, use the pan/tilt keys to choose SET ALL. Press the OPEN key . All boxes will contain a symbol as shown in Figure 8.
Pelco Manual C581M-B (1/04) 31 HELP MENU The Help menu is accessed from any other menu. 1. Use the pan/tilt keys in any menu to highlight HELP . 2. Press the OPEN key .
32 Pelco Manual C581M-B (1/04) MUL TIPLE CAMERA DISPLA Y SETUP The multiple camera display formats may be configured using the keyboard. The LEDs above the camera buttons on the multiplexer will illuminate to indicate which cameras are being displayed.
Pelco Manual C581M-B (1/04) 33 PROGRAMMING THE 9-CAMERA DISPLA Y ( Key) Y ou can program two groups of nine cameras each. Both groups can be programmed to include any nine cameras. is not available in simplex RECORD mode. To program the nine-camera displays: 1.
34 Pelco Manual C581M-B (1/04) PROGRAMMING MENU DEF AUL TS T able E. Programming Menu Defaults Menu Item Default System Setup T ime Display On T itle Display On Normal Record Speed 2/6/8 Hr (NTSC/EIA).
Pelco Manual C581M-B (1/04) 35 PROGRAMMING A PRESET 1. Press the MAIN or SPOT MONIT OR key . The green LED over the MAIN or SPOT key lights. When using the MAIN MONITOR, the SPOT MONITOR DISPLA Y menu item in the Advanced System Setup menu must be set to TRACK MAIN (refer to the Advanced System Setup section).
36 Pelco Manual C581M-B (1/04) TROUBLESHOOTING If you have difficulty operating your system, run through the following checklist to see if you can solve the problem. 1. Are the keyboard switches set properly? 2. Is the equipment wired properly? 3. Are the menu options in the multiplexer(s) and server set properly? 4.
Pelco Manual C581M-B (1/04) 37 18. If the UNIT ID, in the ADV ANCED SYSTEM SETUP menu, is inadvertently changed at the keyboard resulting in an uncontrollable sequencing of unit ID numbers and loss of keyboard control: a. Go to the multiplexer and press the down arrow button.
38 Pelco Manual C581M-B (1/04).
Pelco Manual C581M-B (1/04) 39 REVISION HISTOR Y Manual # Date Comments C581M 8/99 Original version. C581M-A 9/03 Added Regulatory Notices section and changed power specification. C581M-B 1/04 Revised per ECO #03-9291, software upgrade to increase the number of programmable patterns.
W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .
An important point after buying a device Pelco C581M-B (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco C581M-B yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco C581M-B - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco C581M-B you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco C581M-B will certainly help you make a decision on the purchase.
If you already are a holder of Pelco C581M-B, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco C581M-B.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco C581M-B. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco C581M-B along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
