EN
Peerless Industries logo
Official user manual

Peerless Industries ST630

23 pages·3.8 MB·TV Mount·PDF·EN
Peerless Industries ST630
Table of Contents 21 sections Models: ST630P, ST630P-S, ST630, ST630-S · © U L US C · ISSUED: 02-05-09 SHEET #: 201-9421-9 06-03-09 · WALL CONSTRUCTION HARDWARE REQUIRED · … ShowHide
Page 1 of the Peerless Industries ST630 user manual — ISSUED: 02-05-09 SHEET #: 201-9421-9 06-03-09
Page 1 · click to enlarge
Page 1

Installation and Assembly: SmartMount™ Universal Tilt Wall Mount for 10" - 24" (25 - 61 cm) LCD Flat Panel Screens

Models: ST630P, ST630P-S, ST630, ST630-S

  • Features:
  • Fits 10" - 24" (25 - 61 cm) LCD flat panel screens
  • One-touch tilt for effortless positioning and adjustment of the screen

© U L US C

Max Load Capacity80 lb (36.3 kg)

ISSUED: 02-05-09 SHEET #: 201-9421-9 06-03-09

Page 3 of the Peerless Industries ST630 user manual — D
Page 3 · click to enlarge
Page 3

Before you begin, make sure all parts shown are included with your product.

Parts List

ST630P ST630P-S ST630 ST630-S

Description Qty Part # Part # Part # Part # A hook bracket 1 095-1346 095-4346 095-1346 095-4346

B tilt assembly 1 095-0359 095-0360 095-0359 095-0360

C concrete anchor 2 590-0320

D M4 x 10 mm phillips screw 4 504-9012

E M4 x 20 mm phillips screw 4 504-9020

F retaining spacer 4 590-5005

G #14 x 2.5" wood screw 2 5S1-015-C03

H M5 x 6 mm screw 1 520-1023 520-1023 520-1114 520-1114

I security driver 1 - - 560-1133 560-1133

Parts may appear slightly different than illustrated.

D

F

E

A

H

G

Page 4 of the Peerless Industries ST630 user manual — G
Page 4 · click to enlarge
Page 4

Installation to Single Wood Stud Wall

  • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
  • Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.
  • Never tighten in excess of 80 in.
  • lb (9 N.M.).
  • Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is highly recommended.
  • Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers are responsible to provide hardware for other types of mounting situations (not evaluated by UL).

Use a stud finder to locate the edges of the stud. Use of an edge-to-edge stud finder is highly recommended. Based on its edges, draw a vertical line down the stud’s center. Place tilt assembly (B) on wall as a template, making sure that the two mounting holes are over the stud centerline. Level tilt assembly, and mark the center of the two holes. Drill two 5/32" (4 mm) dia. holes 2.5" (64 mm) deep. Make sure that the tilt assembly is level, secure it using two #14 x 2.5" wood screws (G) as shown.

Skip to step 2.

G

Page 5 of the Peerless Industries ST630 user manual — INCORRECT CORRECT
Page 5 · click to enlarge
Page 5

Installation to Solid Concrete or Cinder Block

  • When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35 mm) of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
  • Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
  • Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware and components.

Make sure that tilt assembly (B) is level, use it as a template to mark two mounting holes. Drill two 5/16" (8 mm) dia. holes to a minimum depth of 2.5" (64 mm). Insert anchors (C) in holes flush with wall as shown (right). Place tilt assembly over anchors and secure with two #14 x 2.5" screws (G). Level, then tighten all fasteners.

concrete surface 1

Drill holes and insert anchors (C).

  • Tighten screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage screws, greatly reducing their holding power.

C G

Place plate (B) over anchors (C) and secure with screws (G).

  • Never tighten in excess of 80 in.
  • lb (9 N.M.).
  • Always attach concrete expansion anchors directly to load-bearing concrete.
  • Never attach concrete expansion anchors to concrete covered with plaster, drywall, or other finishing material. If mounting to concrete surfaces covered with a finishing surface is unavoidable, the finishing surface must be counter bored as shown below. Be sure concrete anchors do not pull away from concrete when tightening screws. If plaster/drywall is thicker than 5/8" (16 mm), custom fasteners must be supplied by installer (not evaluated by UL).

Tighten all fasteners.

cinder block solid concrete

INCORRECT CORRECT

CUTAWAY VIEW

B C

G

Show 5 more labels / short text on this page
wall plate · concrete concrete · wall plate · plaster/ dry wall · plaster/ dry wall
Page 6 of the Peerless Industries ST630 user manual — F
Page 6 · click to enlarge
Page 6

Attaching Adapter Plate to Flat Panel Screen

  • If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured, damage may occur to screen or product may fail.

FOR VESA® 75 MOUNTING PATTERN: Choose hole pattern as shown below. Attach hook plate (A) to back of screen using four M4 x 10 mm screws (D) as shown below.

FOR VESA® 100 MOUNTING PATTERN: Choose hole pattern as shown below. Attach hook plate (A) to back of screen using four M4 x 10 mm screws (D) as shown below.

*Note: If hole pattern is in a pocket, attach hook plate (A) to back of screen using four M4 x 20 mm screws (E) and four retaining spacers (F) as indicated below.

A

A

D

D

*For screens with a hole pattern in a pocket, spacers (F) go between hook plate (A) and screen.

F

Page 7 of the Peerless Industries ST630 user manual — fig. 4.1
Page 7 · click to enlarge
Page 7

Installing and Removing Flat Panel Screen

Attach screen to tilt assembly (B). Tighten M5 x 6 mm screw (H) to lock screen to tilt assembly.

H

A

To remove screen from mount, loosen screw (H) and lift screen off of mount.

  • Do not lift more weight than you can handle. Use additional man power or mechanical lifting equipment to safely handle placement of the screen.
  • Failure to lock hook plate ( A ) with screw ( H ) can cause screen to come off mount if hit accidentally.
  • Do not tighten screws with excessive force. Overtightening can cause damage to mount. Tighten screws to 20 in.
  • lb (2.26 N.M.) maximum torque.

fig. 3.1

Adjust tension knob on right side of mount shown in figure 4.1 to desired tension to balance your screen size and weight.

Push or pull from top or bottom of screen to adjust tilt as shown in figure 4.1. The tilt can be adjusted to a maximum of 15° forward or 5° backward.

CAUTION

  • Do not tighten screws with excessive force. Overtightening can cause damage to mount. Tighten screws to 40 in.
  • lb (4.5 N.M.) maximum torque.
  • Be careful not to pinch fingers when pushing screen from the bottom.

fig. 4.1

© 2009, Peerless Industries, Inc. All rights reserved. All other brand and product names are trademarks or registered trademarks of their respective owners.

Peerless Industries, Inc.

3215 W. North Ave. Melrose Park, IL 60160 www.peerlessmounts.com

screen · tension knob

Page 8 of the Peerless Industries ST630 user manual — PUBLICADO: 02-05-09 HOJA #: 201-9421-9 06-03-09
Page 8 · click to enlarge
Page 8

Instalación y ensamblaje: Soporte universal de pared SmartMount™ con capacidad de in- clinación para pantallas planas de LCD de 10" a 24" (25 - 61 cm)

Modelos: ST630P, ST630P-S, ST630, ST630-S

  • Características:
  • Sostiene pantallas planas de 10" - 24" (25 - 61 cm)
  • Inclinación de un solo toque para permitir la colocación y el ajuste de la pantalla sin esfuerzo

© U L US C

Máxima capacidad de carga UL:

80 lb (36.3 kg)

PUBLICADO: 02-05-09 HOJA #: 201-9421-9 06-03-09

Ask about the Peerless Industries ST630

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Peerless Industries ST630

Be the first to ask — other owners or our team will answer.

Original document

Peerless Industries ST630 manual PDF

23 pages·3.8 MB·TV Mount·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…