EN
Peerless Industries logo
Official user manual

Peerless Industries RTONE

33 pages·1.6 MB·TV Mount·PDF·ENDEITNLJA
Peerless Industries RTONE
Table of Contents 38 sections Installation and Assembly: OneMount™ · Models: ONE-TP, ONE-TP-S, RTONE, RTONES · Tools Needed for Assembly · Accessories: · … ShowHide
Page 1 of the Peerless Industries RTONE user manual — Models: ONE-TP, ONE-TP-S, RTONE, RTONES
Page 1 · click to enlarge
Page 1

Installation and Assembly: OneMount™

Models: ONE-TP, ONE-TP-S, RTONE, RTONES

This product is UL Listed. It must be installed by a qualified professional installer.

Peerless Industries RTONE — Models: ONE-TP, ONE-TP-S, RTONE, RTONES diagram (page 1)
Fig. 1 · Models: ONE-TP, ONE-TP-S, RTONE, RTONES

Max UL Load Capacity 250lb (113.5kg)

  • Features:
  • Fits 23" to 84" flat panel screens
  • Easily expandable adapter brackets and wall plate
  • Adjustable tilt of +15°/-5° for viewing flexibility
  • Intuitive design for easy installation
  • Security hardware for theft resistance and safety
  • 3215 W. North Ave.
  • Melrose Park, IL 60160
  • (800) 729-0307 or (708) 865-8870
  • Fax: (708) 865-2941
  • <a href="http://www.peerlessmounts.com" rel="nofollow noopener" target="_blank">www.peerlessmounts.com</a>

Page 4 of the Peerless Industries RTONE user manual — BOTTOM EXTENSION BRACKET
Page 4 · click to enlarge
Page 4

Adjustment of Extension Brackets

Loosen four 1/4-20 x 1/4" screws on each adapter bracket (BB,CC). Position extension brackets, with slots facing downward, onto adapter brackets (BB,CC) at the appropriate position to accommodate your screen as shown in Figure 1.1. Securely tighten all 1/4-20 x 1/4" screws as shown in figure 1.2.

TOP EXTENSION BRACKET

BB,CC

BB,CC

STOP ADAPTER BRACKET

TIGHTEN FASTENERS

1/4-20 x 1/4" SCREWS

STOP

Make sure slots face downward.

BOTTOM EXTENSION BRACKET

fig 1.1 fig 1.2

Page 5 of the Peerless Industries RTONE user manual — Attaching Tilt Brackets to Screen using Baffled Fastener Pack
Page 5 · click to enlarge
Page 5

Attaching Tilt Brackets to Screen using Baffled Fastener Pack

Peerless Industries RTONE — Attaching Tilt Brackets to Screen using Baffled Fastener Pack diagram (page 5)
Fig. 2 · Attaching Tilt Brackets to Screen using Baffled Fast…
  • Tighten screws so adapter brackets are firmly attached. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to 40 in.
  • lb (4.5 N.M.) maximum torque.
  • If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured, damage may occur to screen or product may fail.

To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place screen face side down. Refer to screen manufacturers instructions or customer service, for removing any knobs, base, cover, or screw(s) on the back of the screen to prepare mounting. These need to be removed to allow the adapter brack- ets to be attached. Select the small, medium, large or extra large screws from the baffled fastener pack then attach tilt brackets to screen following figure 2.3 or 2.4.

Peerless Industries RTONE — Attaching Tilt Brackets to Screen using Baffled Fastener Pack diagram (page 5)
Fig. 3 · Attaching Tilt Brackets to Screen using Baffled Fast…
  • Use the corresponding hole in the multi-washer that matches your screw size as shown in fig 2.2.
Page 6 of the Peerless Industries RTONE user manual — SCREEN
Page 6 · click to enlarge
Page 6

For Flat Back Screen

Begin with the shortest length screw, hand thread through multi-washer and adapter bracket into screen as shown below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the baffled fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.

If you have any questions, please call Peerless customer care at 1-800-729-0307 or visit our website at www.peerlessmounts.com/charts to locate your screen compatibility chart.

SCREEN

MULTI-WASHER

SCREW

ADAPTER BRACKET (BB or CC)

For Bump-out or Recessed Back Screen

Begin with longer length screw, hand thread through multi-washer, adapter bracket and spacer in that order into screen as shown below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the baffled fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.

If you have any questions, please call Peerless customer care at 1-800-729-0307 or visit our website at www.peerlessmounts.com/charts to locate your screen compatibility chart.

SCREEN

MULTI-WASHER

SPACER

SCREW

ADAPTER BRACKET (BB or CC)

Page 7 of the Peerless Industries RTONE user manual — For Flat Back Screen
Page 7 · click to enlarge
Page 7

With tape measure, measure the outside to outside of the brackets on the back of your screen. If width of the tilt brackets on back of the screen is over 18-1/2" shown in figure 3.1, using a 7/16" wrench, attach wing bracket (GG) to center bracket using two 1/4" serrated flanged locknuts (FF) as shown in figure 3.2. If width of the brackets on back of the screen is over 30-3/8", using a 7/16" wrench, attach second wing bracket (GG) to center bracket using two 1/4" serrated flanged locknut (FF) as shown in figure 3.3.

Peerless Industries RTONE — For Flat Back Screen diagram (page 7)
Fig. 4 · For Flat Back Screen
Page 8 of the Peerless Industries RTONE user manual — Installation to Double Wood Stud Wall
Page 8 · click to enlarge
Page 8

Installation to Double Wood Stud Wall

  • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
  • Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.
  • Never tighten in excess of 80 in.
  • lb (9 N.M.).
  • Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is highly recommended.
  • Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers are responsible to provide hardware for other types of mounting situations.

Wall plate (AA) can be mounted to two studs that are 16" apart. Use a stud finder to locate the edges of the studs. Use of an edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical line down each stud’s center. Place wall plate on wall as a template. The top mounting slots should be 2.5" above the desired screen center as shown in figure 4.1. Level plate, and mark the center of the four mounting holes. Make sure that the mounting holes are on the stud centerlines. Drill four 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Make sure that the wall plate is level, secure it using four #14 x 2.5" wood screws (DD) as shown in figure 4.2.

Skip to step 5.

Peerless Industries RTONE — Installation to Double Wood Stud Wall diagram (page 8)
Fig. 5 · Installation to Double Wood Stud Wall
Peerless Industries RTONE — Installation to Double Wood Stud Wall diagram (page 8)
Fig. 6 · Installation to Double Wood Stud Wall

4" (102 mm)

Page 9 of the Peerless Industries RTONE user manual — Installation to Triple Wood Stud Wall
Page 9 · click to enlarge
Page 9

Installation to Triple Wood Stud Wall

  • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
  • Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.
  • Never tighten in excess of 80 in.
  • lb (9 N.M.).
  • Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is highly recommended.
  • Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers are responsible to provide hardware for other types of mounting situations.

Wall plate (AA) can be mounted to three studs that are 16" apart. Use a stud finder to locate the edges of the studs. Use of an edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical line down each stud’s center. Place wall plate on wall as a template. The top mounting slots should be 2.5" above the desired screen center as shown in figure 4.3. Level plate, and mark the center of the six mounting holes. Make sure that the mounting holes are on the stud centerlines. Drill six 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Make sure that the wall plate is level, secure it using six #14 x 2.5" wood screws (DD) as shown in figure 4.4.

Skip to step 5.

Peerless Industries RTONE — Installation to Triple Wood Stud Wall diagram (page 9)
Fig. 7 · Installation to Triple Wood Stud Wall
Page 10 of the Peerless Industries RTONE user manual — EE
Page 10 · click to enlarge
Page 10

Installation to Solid Concrete or Cinder Block

  • When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
  • Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
  • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

Make sure that wall plate (AA) is level, use it as a template to mark four mounting holes. The top mounting hole should be 2.5" above the desired screen center as shown in figure 4.1 on page 8. Drill four 1/4" (6 mm) dia. holes to a minimum depth of 2.5" (64 mm). Insert anchors (EE) in holes flush with wall as shown (right). Place wall plate over anchors and secure with #14 x 2.5" screws (DD). Level, then tighten all fasteners.

concrete surface 1

EE

Drill holes and insert anchors (EE).

WARNING • Tighten screws so that wall plate is firmly attach but do not overtighten. Overtightening can dam screws, greatly reducing their holding power. • Never tighten in excess of 80 in. • lb (9 N.M.). WARNING • Always attach concrete anchors directly to load bearing concrete. • Never attach concrete anchors to concrete cover with plaster, drywall, or other finishing material. I mounting to concrete surfaces covered with a fin surface is unavoidable, the finishing surface mus counterbored as shown below. Be sure concrete anchors do not pull away from concrete when tig ing screws. If plaster/drywall is thicker than 5/8" custom fasteners must be supplied by installer. (Not evaluated by UL)- ed f ishing t be hten- , wall VIEW plate CUTAWAY

EE DD

Place plate (AA) over anchors (EE) and secure with screws (DD).

Tighten all fasteners.

solid concrete cinder block

EE

Page 11 of the Peerless Industries RTONE user manual — LOCATOR
Page 11 · click to enlarge
Page 11

Mounting and Removing Flat Panel Screen

  • Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television.

BB and CC

Adjust brackets to full back tilt position and tighten. Hook tilt brackets (BB and CC) onto wall plate (AA). Then slowly swing screen in as shown. Turn safety screws, using wrench (II), clockwise till fully tightened down and screw tip securely contacts bottom of the wall plates as shown in detail 1. of figure 5.1. Center of screen can be adjusted horizontally no more than 4" from center of the wall plate configuration, if desired as shown in figure 5.2.

SAFETY

SCREW

DETAIL 1

To remove screen from mount, loosen safety screws, swing screen away from mount, and lift screen off of mount.

CAUTION • Do not tighten screws wit Overtightening can cause screws to 40 in. • lb (4.5h excessive force. damage to mount. Tighten N.M.) maximum torque. CAUTION • Be careful not to pinch fin from the bottom.gers when pushing screen Adjusting the Tilt A Panel Screen Adjust tension knobs tension, balancing you tension knob, without can be pulled out, awa independently of the k shown in Detail 3. Push or pull from top o tilt as shown in figure a maximum of 15° forw NOTE: To lock the scr position, use locator h Tighten IncreLok™ tilt brackets as shown in f

CS = center of screen

LOCATOR

HOLE

TENSION

KNOB

TILT POSITION

HOLES

DETAIL 2

SCREW

TENSION

KNOB

DETAIL 3

© 2006 Peerless Industries, Inc. All rights reserved. Onemount is a trademark and Peerless is a registered trademark of Peerless Industries, Inc. All other brand and product names are trademarks or registered trademarks of their respective owners.

4" · · IncreLok™ TILT LOCKING

Ask about the Peerless Industries RTONE

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Peerless Industries RTONE

Be the first to ask — other owners or our team will answer.

Original document

Peerless Industries RTONE manual PDF

33 pages·1.6 MB·TV Mount·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…