Instruction/ maintenance manual of the product CA-A800B Peavey
Go to page of 36
C A-A540B /C A-A800B C inema Po wer Amplif iers ™ ™ Oper at ing Guide Oper at ing Guide ¨.
Intended to alert the user to the presence of uninsulated Òdangerous voltageÓ within the productÕs enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. Intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
CA-A540B ª and CA-A800B ª Common Features ¥ SPS ª compression with LED indicators and defeat switch ¥ Slew Rate: 20 V/microsecond, stereo mode ¥ Frequency Response (each channel): 20 Hz to 20 kHz, ±0.2 dB, at rated power ¥ T otal Harmonic Distortion: Less than 0.
(1) SPS COMPRESSION ACTIVE LED These indicators, one per channel, illuminate when SPS compression is taking place. This LED becomes a CLIP indicator when the rear panel SPS ENABLE/DEFEA T switch is in the DEFEA T position. (2) POWER LED This indicator illuminates when AC mains power is applied to the amplifier and both channels are operational.
(4) MAINS POWER SOURCE All CinemAcoustics Series power amplifiers are fitted with a single, heavy-duty , three-conductor line cord and a conventional, three-terminal AC plug with a ground pin for 120 V products. For 100 V and 220 V products, the line cord is fitted with the appropriate power connector .
breaker trips instantly each time you attempt to reset it, the unit should be taken to a qualified service center for repair . (6) OUTPUT MONITOR This standard Quick-Connect ª RJ1 1 modular connector provides Channel A and B signals to PeaveyÕs booth monitor products such as the CA-M400.
(1 1) EURO CONNECTOR INPUTS The popular plugable Euro connector is provided for the inputs for each channel. These inputs are balanced electronically , with the terminals marked Ò+Ó as the positive amplifier inputs, and the terminals marked Ò-Ó as the negative amplifier inputs.
quickly . In all circumstances, an investigation should be undertaken to determine the cause of the thermal shut down. If the amplifier is not severely overloaded or its outputs shorted, and air flow .
Characteristics: CA-A540B CA-A800B Output Power 1, 2, 3: 2 Channel Mode, Stereo 4 ohms, 1 kHz at 1% THD 450 W RMS per channel 700 W RMS per channel 8 ohms, 1 kHz at 1% THD 270 W RMS per channel 400 W RMS per channel Bridge Mode, Mono 8 ohms, 1 kHz at 1% THD 900 W RMS 1400 W RMS Rated Output Power 1, 2: 4 ohms, 20 Hz to 20 kHz, 0.
IMPORT ANT SAFETY INSTRUCTIONS W ARNING: When using electric products, basic cautions should always be followed, including the following: 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water .
CA-A540B ª y CA-A800B ª Caracter’sticas comunes ¥ Compresi—n SPS ª con LED indicadores e interruptor de anulaci—n ¥ V elocidad de transici—n: 20 V/µs, modo estereof—nico ¥ Respuesta d.
(1) LED INDICADOR DE COMPRESIîN SPS ACTIV A Estos indicadores, uno por canal, se encienden cuando est‡ activa la compresi—n SPS. Si el conmutador ENABLE/DEFEA T (activar/anular) del panel posterior se encuentra en la segunda posici—n, el LED indica la condici—n de recorte de la se–al.
(4) FUENTE DE ALIMENT ACIîN PRINCIP AL T odos los amplificadores de la serie CinemAcoustics para 120 V cuentan con un œnico cable de alimentaci—n de tres conductores para servicio pesado, y un enchufe para CA de tres terminales con terminal de tierra.
(6) MONITOR DE SALIDA Este conector modular est‡ndar es del tipo RJ1 1 Quick-Connect ª y proporciona se–ales a los canales A y B de los monitores de cabina Peavey , tales como el modelo CA-M400. La polaridad adecuada de los conectores se muestra en el diagrama anterior .
INST ALACIîN Y CONFIGURACIîN La serie de amplificadores de potencia CinemAcoustics se ha dise–ado para asegurar la durabilidad y el alto rendimiento en salas de cine y teatro.
OPERACIîN CON COMPRESIîN SPS El sistema de compresi—n patentado de Peavey maximiza el rendimiento del amplificador porque impide que la se–al se recorte, incluido al entregar m‡xima potencia.
ESPECIFICACIONES DE LOS AMPLIFICADORES CA-A540B ª y CA-A800B ª Caracter’sticas: CA-A540B CA-A800B Potencia de salida 1, 2, 3: Modo de 2 canales (estereof—nico) 4 ½ a 1 kHz, DA T 1 % 450 Wef por.
18 INSTRUCCIONES DE SEGURIDAD IMPOR T ANTES ADVER TENCIA: Al utilizar productos elŽctricos se deben respetar las precauciones b‡sicas, que incluyen las siguientes: 1. Lea estas instrucciones. 2. Conserve estas instrucciones. 3. Preste atenci—n a todas las advertencias.
CA-A540B ª et CA-A800B ª CaractŽristiques: ¥ Protection SPS ª avec indicateurs LED et interrupteur ¥ Slew Rate: 20 V/microsecond, mode stŽrŽo ¥ RŽponse en frŽquence (chaque canal): 20 Hz ˆ 20 kHz, ±0.2 dB, ˆ puissance nominale ¥ Distorsion harmonique totale: moins de 0.
(1) LED DÕACTIV A TION DE LA PROTECTION SPS Ces indicateurs (un par canal) sÕallument lorsque la protection SPS se met en action. Ils indiquent lÕŽcr•tage lorsque lÕinterrupteur SPS est en position DEFEA T . (2) LED DÕALIMENT A TION Cette LED sÕallume lorsque lÕappareil est sous tension et que les deux canaux sont opŽrationnels.
(4) Connecteur IEC T ous les amplificateurs de la série CinemAcoustics est équipé d’un connecteur IEC universel. Un cordon de calibre #16 A WG 3 (section de 1,3 cm2 mimimum) équipé d’une connexion à la terre doit être utilisé. Il doit être connecté à une source de courant capable de fournir au moins 7 ampères.
reliŽes ˆ la masse (masse du ch‰ssis). L ÕimpŽdance minimum recommandŽe en sortie de lÕamplificateur est de 4 Ohm par canal ou 8 Ohm en mode Bridge. L Õutilisation de lÕamplificateur avec des charges infŽrieures peut entra”ner lÕarr•t momentanŽ de lÕappareil.
INST ALLA TION ET REGLAGE Les amplificateurs de la sŽrie CinemAcoustics sont con•us pour fournir les performances et la qualitŽ sonore exigŽes pour des utilisations en thŽatre ou cinŽma. Ils sont refroidis par deux ventilateurs ˆ deux vitesses.
24 Characteristics: CA-A540B CA-A800B Output Power 1, 2, 3: 2 Channel Mode, Stereo 4 ohms, 1 kHz at 1% THD 450 W RMS per channel 700 W RMS per channel 8 ohms, 1 kHz at 1% THD 270 W RMS per channel 400 W RMS per channel Bridge Mode, Mono 8 ohms, 1 kHz at 1% THD 900 W RMS 1400 W RMS Rated Output Power 1, 2: 4 ohms, 20 Hz to 20 kHz, 0.
25 NOTE IMPORT ANTE CONCERNANT LA SECURITE A TTENTION: Lors de lÕutilisation de appareils Žlectriques, certaines mesures de sŽcuritŽ doivent •tre respectŽes: 1. Lisez toutes les instructions. 2. Conservez ces instructions. 3. T enez compte de tous les avertissements.
CA-A540B ª und CA-A800B ª Features ¥ SPS ª Kompression mit LED Anzeige (schaltbar) ¥ Slew Rate: 20 V / microsecond, Stereo Modus ¥ Frequenz Gang (je Kanal): 20 Hz bis 20 kHz, ±0.
(1) SPS KOMPRESSOR/LIMITER LED Diese LEDs zeigen an jedem Kanal das Einsetzen des SPS KOMPRESSOR/LIMITERS an. Sie werden zu CLIP Anzeigen, wenn der SPS Schalter auf der RŸckseite des GerŠtes in der DEFEA T Position steht. (2) POWER LED Zeigt die Betriebsbereitschaft des V erstŠrkers an.
(4) NETZANSCHLUSS Die CinemAcoustics Serie verfŸgt Ÿber einen konventionellen 3-Pol-Netzanschlu§ (120V V ersion). Bei den 100V und 220V V ersionen (220V = Deutschland) ist das Netzkabel fest mit dem GerŠt verbunden. Bitte nehmen Sie zur Kenntnis, da§ bei der 220V V ersion des V erstŠrkers etwa 7.
(8) SPS SCHAL TER Mit diesem Schalter wird der SPS Kompressor/Limiter ein- bzw . ausgeschaltet. Der Schalter sollte normaler Weise immer auf ENABLE Position stehen, um den V erstŠrker zu schŸtzen. Eine Abschaltung der SPS Funktion kann bei †berlast oder clipping zur Abschaltung durch den Circuit Breaker (5) kommen.
schaltet. Dies ist normal und bedarf keiner †berprŸfung. Es kann auch sein, da§ der V erstŠrker sich abschaltet. Dies ist der Fall wenn nicht genŸgend frische Luft angesaugt werden kann oder die V entilation zur V orderseite behindert wird. In diesem Fall geht die POWER LED auf der V orderseite des GerŠtes aus.
31 Characteristics: CA-A540B CA-A800B Output Power 1, 2, 3: 2 Channel Mode, Stereo 4 ohms, 1 kHz at 1% THD 450 W RMS per channel 700 W RMS per channel 8 ohms, 1 kHz at 1% THD 270 W RMS per channel 400 W RMS per channel Bridge Mode, Mono 8 ohms, 1 kHz at 1% THD 900 W RMS 1400 W RMS Rated Output Power 1, 2: 4 ohms, 20 Hz to 20 kHz, 0.
32 WICHTIGE SICHERHEITSRICHTLINIEN W ARNUNG: Beim Einsatz elektrischer GerŠte sollten stets nachfolgend genannte grundlegende Sicherheitsrichtlinien beachtet werden: 1. Lesen Sie diese Richtlinien. 2. Bewahren Sie diese Richtlinien stehts grif fbereit auf.
NOTES: 33.
34 NOTES:.
CinemAcoustics ª Division PEA VEY ELECTRONICS CORPORA TION LIMITED W ARRANTY Effective Date: November 1, 1998 What This W arranty Covers Y our Peavey CinemAcoustics Warranty covers defects in material and workmanship in CinemAcoustics products purchased and service d in the U.
Features and specifications subject to change without notice. Peavey Electronics Corporation ¥ 71 1 A Street ¥ Meridian ¥ MS ¥ 39301 (601) 483-5376 ¥ F AX (601) 486-1678 ¥ www .
An important point after buying a device Peavey CA-A800B (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Peavey CA-A800B yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Peavey CA-A800B - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Peavey CA-A800B you will learn all the available features of the product, as well as information on its operation. The information that you get Peavey CA-A800B will certainly help you make a decision on the purchase.
If you already are a holder of Peavey CA-A800B, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Peavey CA-A800B.
However, one of the most important roles played by the user manual is to help in solving problems with Peavey CA-A800B. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Peavey CA-A800B along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
