Instruction/ maintenance manual of the product 9433 Paxar
Go to page of 10
TC9433VMOI Rev AB 8/08 ©2006 Pa xar Americas, Inc. a subsidiary of Avery Dennison Corporation. All Rights Reserved. MONARCH 9433™ VEHICLE MOUNT INSTRUCTIONS Using the Vehicle Mount, you can attach your Monarch 9433 printer to a forklift or other vehicle.
2 DB9 Connector USB Port USB Cable Connecting the Communications Cables The printer uses either 9-pin serial communications or USB communications. For best results, use only Monarch® cables. Open the hinged cable door by loosening the two Phillips screws and lifting up on the door.
. 3 Installing on a Tabletop 1. Select a suitable location for the mount on your vehicle. 2. Align the four outside holes on the vehicle mount with the corresponding holes in your vehicle. 3. Place the four dampening washers between the vehicle and the bottom of the vehicle mount.
4 Installing Overhead (Upside Down) 1. Select a suitable location for the mount on your vehicle. 2. Center the clamping plate on two of your vehicle’s overhead rails. 3. Align the four inside nuts in the vehicle mount with the holes in the clamping plate.
. 5 Installing Vertically No screws or mounting hardware are provided for vertical installation. 1. Select a suitable location for the mount on your vehicle.
6 Attaching the Printer To attach the printer on the vehicle mount: 1. Make sure the printer’s battery and communication cable are installed. 2. Insert the printer into the brackets of the vehicle mount using the knobs as a guide. 3. Push down firmly on the brackets so the printer locks completely in place.
. 7 Securing the Cables Use the cable guides located on the inside and front of the vehicle mount to secure any cables. 1. Attach the printer to the vehicle mount. 2. Thread the cable through the first opening and out the second opening of the cable guide on the inside of the mount, then through the cable guide in the front of the mount.
8 Loading Supplies To load supplies into the printer: 1. Turn off the printer. 2. Attach the printer to the vehicle mount. 3. Squeeze the supply bracket and the spring-loaded supply holder. Pull the hook end of the supply holder and turn it to the left to release the supply bracket.
. 9 6. Pull the release levers located on both sides of the printer to open the supply door. 7. Insert an empty 3-inch core in between the supply holder tabs to open them to their widest position. 8. Slide the supply guides, located inside the printer on each side of the external supply slot, out to their widest position.
10 10. Center-adjust the supply guides so that they barely touch the edge of the supply. 11. Pull out enough supply to lay across the exit chute. 12. Close the supply door until the release levers click into place. 13. Turn on the printer. 14. Press F to advance the supply.
An important point after buying a device Paxar 9433 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Paxar 9433 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Paxar 9433 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Paxar 9433 you will learn all the available features of the product, as well as information on its operation. The information that you get Paxar 9433 will certainly help you make a decision on the purchase.
If you already are a holder of Paxar 9433, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Paxar 9433.
However, one of the most important roles played by the user manual is to help in solving problems with Paxar 9433. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Paxar 9433 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
