Instruction/ maintenance manual of the product IM2RC/K Patton electronic
Go to page of 11
USER MANU AL MODELS IM1/K and IM2RC/K G.703/G.704 QuikConnect™ and Rear Card Modules SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www .
1 T ABLE OF CONTENTS SECTION P AGE 1.0 W arranty Information .............................................................2 1.1 W arranty Statement 1.2 Radio and TV Interference 1.3 CE and T elecommunication Approvals 1.4 Service Information 2.0 General Information .
3 1.2 RADIO AND TV INTERFERENCE The Models IM1/K and IM2RC/K (K Module) generate and use radio frequency energy , and if not installed and used properly—that is, in strict accordance with the manufacturer's instructions—may cause interference to radio and television reception.
3.0 TYPICAL APPLICA TION The K Module can be deployed in one of two applications: G.703/G.704 Network T ermination (nx64kpbs to 2.048Mbps), and G.703/G.
3.2 NETWORK EXTENSION APPLICA TION Network Extension mode is used to extend nx64 -2.048Mbps G.703/G.704 service across a DSL link, providing an nx64 G.703/G.704 link at the remote site. T ransmitter clocking is derived from the G.703/G.704 network, and transmitted over the baseband modem link (refer to Figure 2, below).
9 10 Switch S1-3 : Clear Channel Mode When S1-3 is at Off position, the K Module is running in G.703 clear channel mode. When S1-3 is at On position, the K Module is run- ning in G.704 framed mode. When the K Module is set to framed mode, channel 0 will be used to pass G.
12 11 5 5 . . 0 0 I I N N S S T T A A L L L L A A T T I I O O N N This section describes how to install the IM1/K and IM2RC/K mod- ules into your mDSL modems. Please refer to the section in this manu- al that describes your unit. 5.1 Installing the IM1/K The QuickConnect™ interface on the NetLink Modems are inter- changeable Modules.
13 14 5.3 MAKING INTERF ACE CONNECTIONS The Patton K Module may be connected to G.703/G.704 ports using a single 120 ohm RJ-48C or a dual 75 ohm coax (BNC). The Patton K Module rear panels and the location of these connectors are show below in Figure 4.
15 6 6 . . 0 0 O O P P E E R R A A T T I I O O N N Once the Patton K Module is installed and configured, it should operate transparently . Please refer to the base unit (i.e. Model 1095) user manual for instructions on how to read the front panel LEDs, per- form diagnostics, monitor system status, and connect to the DSL line port.
17 18 A A P P P P E E N N D D I I X X B B P A TTON K MODULE CABLE RECOMMENDA TIONS All Patton Electronics Company Baseband Modems, CSU/DSUs and Short Range Modem are tested to the distances published .
A A P P P P E E N N D D I I X X E E P A TTON K MODULE JUMPER SETTINGS Figure C (below) shows the top view of the IM1/K printed circuit board (PCB) and the location of the jumpers. Figure D (below) shows the top view of the IM2RC/K printed circuit board (PCB) and the location of the jumpers.
An important point after buying a device Patton electronic IM2RC/K (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Patton electronic IM2RC/K yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Patton electronic IM2RC/K - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Patton electronic IM2RC/K you will learn all the available features of the product, as well as information on its operation. The information that you get Patton electronic IM2RC/K will certainly help you make a decision on the purchase.
If you already are a holder of Patton electronic IM2RC/K, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Patton electronic IM2RC/K.
However, one of the most important roles played by the user manual is to help in solving problems with Patton electronic IM2RC/K. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Patton electronic IM2RC/K along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
