Instruction/ maintenance manual of the product 07M6070-UM Patton electronic
Go to page of 43
NanoSer v™ Thin System Ultra-Thin System User Manual Sales Office: +1 (301) 975-1000 T echnical Support: +1 (301) 975-1007 E-mail: support@patton.com WWW : www .
Patton Electronics Company , Inc. 7622 Rickenbacker Drive Gaithersburg, MD 20879 USA T el: +1 (301) 975-1000 F ax: +1 (301) 869-9293 Support: +1 (301) 975-1007 W eb: www .
Owner ’ s Record The serial number of this product is located at the rear panel of your system. R efer to the model and serial number when you contact the factory for ser vices. IMPORT ANT THERMAL NOTE ON SYSTEM USAGE: This is a fanless system, so it must be properly mounted to allow for proper cooling.
Hazardous network voltages are present in W AN ports regardless of whether power to the unit is ON or OFF . T o avoid electric shock, use caution when near W AN ports. When detaching the cables, detach the end away from the device first. Do not work on the system or connect or disconnect cables during periods of lightning activity .
5 T able of Contents .........................................................................................................................................................................4 Table of Contents .........................................
6 NanoServ User Manual Table of Contents RMA numbers ................................................................................................................................................29 Shipping instructions .............................
7 Unpacking Y our NanoSer v™ System Congratulations! Y ou have just acquired the world ’ s smallest and most compact embedded system. Check to make sure that you have the follo wing items: Check before use Note The keyboard and mouse ar e not included in the system.
8 Chapter 1 General Information Chapter contents NanoServ™ System Overview ..........................................................................
NanoServ™ System Overview 9 NanoServ™ User Manual 1 • General Information NanoServ™ System Over view The N anoServ™ is a unique tiny embedded system for a wide range of applications, from industrial to office to home. Figure 1. NanoSer v™ System Figure 2.
10 Chapter 2 NanoSer v™ System Over view Chapter contents Ultra-Thin System Overview .................................................................................................................................10 Thin System Overview ...........
Ultra-Thin System Overview 11 NanoServ™ User Manual 2 • NanoServ™ System Overview Ultra-Thin System Overview Figure 3. Ultra-Thin System - Front panel Figure 4. Ultra-Thin System - Back panel Front panel Power LED The power LED lights up when the system is turned on.
Thin System Overview 12 NanoServ™ User Manual 2 • NanoServ™ System Overview Thin System Overview Figure 5. Thin System - Front panel Figure 6. Thin System - Back panel Front panel Power LED The power LED lights up when the system is turned on. HDD LED The HDD LED flashes when the system is working.
13 Chapter 3 Peripherals Chapter contents Introduction ..........................................................................................................................................................13 Connecting the monitor ................
Introduction 14 NanoServ™ User Manual 3 • Peripherals Introduction This chapter shows ho w to connect various devices to the N anoServ™ System. Connect all the devices you will be using before turning on the pow er . The power adaptor should be connected last.
Connecting to the USB, Speaker/Earphone and Internet/Intranet 15 NanoServ™ User Manual 3 • Peripherals Connecting to the USB, Speaker/Earphone and Internet/Intranet *N ote: S peaker/Earphone/Microphone not included.
Connecting the keyboard and mouse 16 NanoServ™ User Manual 3 • Peripherals Connecting the keyboard and mouse *N ote; Keyboard and mouse not included.* T able 5. Connecting the keyboard and mouse Describing Mouse Actions Action Description P oint - Slide and point your mouse to your desired position Click - P ress the left button once.
Connecting the Printer Port 17 NanoServ™ User Manual 3 • Peripherals Connecting the Printer Port T able 6. Connecting the printer por t Printer port The DB-25 printer port is available on the back of the thin system unit. It is used for connecting to a printer .
Connecting the power adaptor 18 NanoServ™ User Manual 3 • Peripherals Connecting the power adaptor There is a difference betw een the power switch on the r ear panel and the system switch on the front panel. The system switch allows the N anoServ™ to suspend or sleep.
19 Chapter 4 BIOS Chapter contents Reconfiguring the system ...........................................................................................
Reconfiguring the system 20 NanoServ™ User Manual 4 • BIOS Reconfiguring the system 1. N ote that the AMI BIOS is used in the system. T o reconfigure the N anoServ™, depress or hit the <Del> key to enter your BIOS setup main menu. 2. Select a setup from the menu.
21 Chapter 5 T aking Care Of Y our NanoSer v™ Chapter contents Storing ...................................................................................................................................................................21 Using cables for connection .
Storing 22 NanoServ™ User Manual 5 • Taking Care Of Your NanoServ™ Storing • Do not place your NanoServ™ in a location that is subject to: - Heating sour ces, such as a stove, o ven, heater .
Using cables for connection 23 NanoServ™ User Manual 5 • Taking Care Of Your NanoServ™ Using cables for connection • T o avoid problems, use only the specified interface cables that match the system. The supplier will not be responsible for problems caused by impr oper connection with other devices or cables.
24 Chapter 6 T roubleshooting Chapter contents Troubleshooting your system .................................................................................................................................24 A. The NanoServ™ does not start ..........
Troubleshooting your system 25 NanoServ™ User Manual 6 • Troubleshooting T roubleshooting your system This section describes the techniques of resolving some basic problems that you may encounter when using your N anoSer v™. F or more troubleshooting guidelines, see “Contacting P atton for assistance” on page 27.
Troubleshooting your system 26 NanoServ™ User Manual 6 • Troubleshooting C. “Operating System Not Found” - A message indicating that “Operating system not found” appears when the N anoServ™ star ts (Win- dows won ’ t start). - Often this message says that an unformatted blank har d disk or blank IDE flash module is installed.
27 Chapter 7 Contacting Patton for assistance Chapter contents Introduction ..........................................................................................................................................................34 Contact information .
Introduction 28 NanoServ™ User Manual 7 • Contacting Patton for assistance Introduction This chapter contains the following information: • “Contact information ” —describes how to contact P atton technical support for assistance.
Warranty Service and Returned Merchandise Authorizations (RMAs) 29 NanoServ™ User Manual 7 • Contacting Patton for assistance Out-of-warranty ser vice P atton ser vices what we sell, no matter how you acquir ed it, including malfunctioning products that are no longer under warranty .
30 Appendix A Factor y Defaults Chapter contents BIOS Defaults .......................................................................................................................................................30 Fedora Core 5 Install Defaults ...
BIOS Defaults 31 NanoServ™ User Manual A • Factory Defaults BIOS Defaults Note Only items changed from the receiv ed bios are listed. 1. PCI / Plug and Play S etup 1.
32 Appendix B Specifications Chapter contents Compliance ...........................................................................................................................................................32 EMC ...............................
Compliance 33 NanoServ™ User Manual B • Specifications Compliance EMC • FCC P ar t 15, Class A • EN55022, Class A • EN55024 Safety • IEC/EN 60950-1 Radio and TV inter ference This equipmen.
System Specifications 34 NanoServ™ User Manual B • Specifications System Specifications T able 8. System Specifications for the NanoSer v™ CPU VIA EDEN N Nano 800MHz North/South Bridge VIA CLE266 + VT8235 Chipsets Main Memory 256MB BIOS “Plug and Play” function, auto-search devices.
Technical Specifications 35 NanoServ™ User Manual B • Specifications T echnical Specifications Note System and technical specifications are subject to change without notice.
Model Numbers 36 NanoServ™ User Manual B • Specifications Model Numbers T able 10. NanoSer v™ Models NanoServ™ 6070 Series Model 6073 Ultra-Thin System Disk-less, fan-less Model 6075 Thin Syst.
37 Appendix C NanoSer v™ System Connectors Chapter contents NanoServ™ System Connectors Summary ...........................................................................................................36 Rear Connectors Outline for the Ultra-Thin System .
NanoServ™ System Connectors Summary 38 NanoServ™ User Manual C • NanoServ™ System Connectors NanoServ™ System Connectors Summar y Rear Connectors Outline for the Ultra-Thin System Figure 8.
Rear Connectors Outline for the Thin System 39 NanoServ™ User Manual C • NanoServ™ System Connectors Rear Connectors Outline for the Thin System Figure 9.
Pin Assignments 40 NanoServ™ User Manual C • NanoServ™ System Connectors Pin Assignments T able 12. J6: KBD (PS/2 Keyboard & Mouse) - 6-pin Mini-Din Connector Pin # Signal Name 1 KBCLK 2 PMCLK 3 GND 4 KBDA T 5 PMDA T 6 SB5V 7 GND 8 GND 9 GND T able 13.
Pin Assignments 41 NanoServ™ User Manual C • NanoServ™ System Connectors T able 15. J17: DC-IN (DC-IN 5V) - 3-pin MINI-DIN Lock Pin Socket Pin # Signal Name 1 J23-pin 1 & 2 2 SB5V 3 NC 4 GND T able 16.
Pin Assignments 42 NanoServ™ User Manual C • NanoServ™ System Connectors T able 19. J6: KBD (PS/2 Keyboard & Mouse) - 6-pin Mini-Din Connector Pin # Signal Name 1 GND 2 LOUTL 3 Open T ouch 4 Open T ouch 5 VREFOUT T able 20.
Pin Assignments 43 NanoServ™ User Manual C • NanoServ™ System Connectors T able 23. LEDS: POWER ON/OFF & HDD R/W LED Color State Green Power On Red HDD On Red Flashes HDD R/W.
An important point after buying a device Patton electronic 07M6070-UM (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Patton electronic 07M6070-UM yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Patton electronic 07M6070-UM - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Patton electronic 07M6070-UM you will learn all the available features of the product, as well as information on its operation. The information that you get Patton electronic 07M6070-UM will certainly help you make a decision on the purchase.
If you already are a holder of Patton electronic 07M6070-UM, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Patton electronic 07M6070-UM.
However, one of the most important roles played by the user manual is to help in solving problems with Patton electronic 07M6070-UM. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Patton electronic 07M6070-UM along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
