Instruction/ maintenance manual of the product 5216 Paradyne
Go to page of 20
TM 1 Hotwire 5216 Remote T ermination Unit (RTU) Customer Premises Installation Instructions Document Number 5216-A2-GN10-10 February 1998 Before Y ou Begin An optional POTS (Plain Old T elephone Service) splitter is available for the 5216 RTU.
2 Package Checklist V erify that your package contains the following: - Model 5216 Remote T ermination Unit (RTU) - DSL interface cable with RJ1 1 modular plugs - Power cord with power transformer - T wo ferrite chokes - W arranty card Refer to Cables & Connectors , page 13, for standard pin numbers.
3 When a POTS splitter is used at both ends of the local loop, wiring is connected: H From the demarcation point to the CP POTS splitter , and H From the demarcation point to the DSL jack.
4 DSL Access without a POTS Splitter When the 5216 RTU is installed without a POTS splitter , a second telephone wiring pair is needed for DSL access. 97-15609 Punchdown Block or NID DSL Jack RT U Cus.
5 Installing the DSL Access Wiring The local loop terminates at the punchdown block or NID. Wiring must be connected from the customer premises side of the punchdown block or the NID to the DSL jack. T ypically , the punchdown block is installed in commercial locations and the NID is installed in residential locations.
6 Green (T1) and red (R1) are the standard wiring colors used in the next two illustrations. In the following example, a NID is used without a POTS splitter .
7 2. Locate the DSL pair of T1/R1 connectors on the customer premises side of the NID or punchdown block. Attach the wiring that will be connected to the DSL jack.
8 DSL Jack Installation The 5216 RTU connects to the local loop via wiring from the demarcation point to an RJ1 1 wall jack. The DSL twisted-pair wiring from the local loop terminates at a new or existing wall jack. It may be necessary to install a standard single RJ1 1 jack or replace a single jack with a double RJ1 1 jack.
9 Installing the R TU Place the 5216 RTU on a flat surface with clearance for the rear connectors. " Procedur e 1. Use the RJ1 1 6-pin cable for the DSL connection. Insert one end of the cable into the jack labeled DSL. Insert the other end into the wall jack labeled DSL.
496-14952 97-15303c Ethernet Line PO WER ETHERNET DSL Hotwire RTU F err ite Choke 10 3. Place the large ferrite choke on the Ethernet cable as closely as possible to the RTU. Pass the Ethernet cable through the ferrite choke twice, creating a loop as shown.
11 6. Close the two halves around the cable and snap the ferrite choke shut. Press down on the plastic latch to secure the ferrite choke in place around the cable. 7. Plug the transformer into an AC outlet. The RTU hardware installation is now complete.
12 LED Status Condition DSL Blinking ON OFF RTU is establishing the DSL link. The LED blinks on and off about five times per second. The DSL link is now active and ready to transmit and receive data. The DSL link has not been established. ETHERNET ON OFF The Ethernet 10BaseT connection to the end-user system is active.
97-15304 6- P i n RJ 1 1 Pl ug DS L Li ne Pi n #1 Pi n #6 13 LED Symptom Action DSL and Ethernet LEDs are on and there is no data transmission. The DSL link and the Ethernet link have been established. If the problem continues, contact the NSP . Ethernet LED is off.
14 H The Ethernet interface crossover cable connector uses an 8-pin, non-keyed modular plug. 97-15305 8- P i n Pl u g E t he r ne t Ca bl e Pi n #1 Pi n #8 10BaseT TX D + 10BaseT TX D 10BaseT R X .
15 Model 5216 R TU T echnical Specifications Item Specification * Height x Width x Depth 1.35 ″ x 6.00 ″ x 8.75 ″ (3.43 cm x 15.35 cm x 22.23 cm) Weight 1 lb. 1 oz. (0.48 kg) Power Class 2 T ransformer normal service input voltage range Input: 100 V ac, 50 Hz; 120 V ac, 60 Hz; or 230 V ac, 50/60 Hz Output: 15 Vdc nominal (+ 10%), minimum 0.
16 Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. Slots and openings in the cabinet are provided for ventilation. T o ensure reliable operation of the product and to protect it from overheating, these slots and openings must not be blocked or covered.
17 CE Marking When the product is marked with the CE mark on the equipment label, this demonstrates full compliance with the following European Directives: H Directive 73/23/EEC – Council Directive .
18 Declaration of Conformity This Declaration of Conformity is made by Paradyne Corporation pursuant to Parts 2 and 15 of the Federal Communications Commission’s Rules. This compliance information statement pertains to the following products: T rade Name: Hotwire Model Number: 5216-A2-200 This device complies with Part 15 of the FCC Rules.
19 EMI W arnings ! W ARNING: T o Users of Digital Apparatus in Canada: This Class B digital apparatus meets all requirements of the Canadian interference-causing equipment regulations. Cet appareil numérique de la classe B respecte toutes les exigences du règlement sur le matérial brouilleur du Canada.
20 W arranty , Sales, and Service Information Contact your local sales representative, service representative, or distributor directly for any help needed.
An important point after buying a device Paradyne 5216 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Paradyne 5216 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Paradyne 5216 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Paradyne 5216 you will learn all the available features of the product, as well as information on its operation. The information that you get Paradyne 5216 will certainly help you make a decision on the purchase.
If you already are a holder of Paradyne 5216, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Paradyne 5216.
However, one of the most important roles played by the user manual is to help in solving problems with Paradyne 5216. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Paradyne 5216 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
