Instruction/ maintenance manual of the product JS950D5C020 Panasonic
Go to page of 28
User’s Manual POS Workstation Model No. JS-950 Series C ontent s For USA / For CA NADA English Read Me First …..….……..... 2 1.Getting S tarted 2.Operation 3.Appendix Before operating this product,please read the i nstructions carefully, and save this manua l for future use.
■ For USA Federal Co mmunications Commission Ra dio Frequency Inte rference Statem ent This equipment has been tested and f ound to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC R ules.
English Read Me First Introduction Thank you for purchasing the JS-950 series Panasonic POS Workstation. This manual describes the instruct ions for the POS Workstation. Please read this manual carefu lly before using this product. List of JS-950 ser ies Product Name Model Number.
1. Getting Started ■ Precautions [POS Workstation: JS-950 series ] IMPORTANT Install a socket outlet adjac ent to the equipm ent so that it will be eas ily accessib le. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES AC CORDING TO THE INSTRUCTIONS.
■ Name of each part & function 1 4 2 3 5 6 1. Oper ator’s Display 2. Front SW cover 3. POP Holder 4. Rear Display 5. USB connector 6. Power SW Attention: Do not push Power SW by mist ake w hen you insert the USB connector.
2. Operation ■ AC Cord Kit Installation 1. How to install the AC Cord (1) Carefully lay the Main Body Unit on a clear, flat surface as show n in figure (1). (2) Unpack the AC Cord, an d then connect it to AC Inl et as shown in figure (2). (3) Fit the Cord Clamp to AC Co rd, and fix it by attached screw as shown in figure (3)-1, 2 and 3.
■ Display Unit Installation Be sure to disconnect the power cabl e of the ma in block (POS Workstation) and confirm the power is “OFF” before the operation below. 1. How to install the display unit (1) Open the screw cover of t he main unit (POS Workstation).
■ Storage Unit Install ation Be sure to disconnect the power cabl e of the ma in block (POS Workstation) and confirm the power is “OFF” before th e operation below.
■ Rear Display Unit Installation Be sure to disconnect the power cabl e of the ma in block (POS Workstation) and confirm the power is “OFF” before th e operation below.
2. How to replace the rear display (1) Loosen the thumbscrew on the lower portion of the rear cover o f the main unit by hand, and remove the rear cover. * The thumbscrew shall be loosened unti l the screw rotates without resistance. (2) Disconnect the connector of the rear disp lay from the connector of the main unit.
■ 2nd display unit Installation Be sure to disconnect the power cabl e of the ma in block (POS Workstation) and confirm the power is “OFF” before th e operation below.
2. How to replace the 2nd Display U nit (1) In case of 950SD010, disconnect VGA c able and speaker cable from I/O panel. (2) Loosen the thumbscrew on the lower portion of the rear cover of the main block by hand, and remove the rear cover. * The thumbscrew shall be loosened unti l the screw rotates without resistance.
■ ID module Unit installation Be sure to disconnect the power cabl e of the ma in block (POS Workstation) and confirm the power is “OFF” before th e operation below. 1. Conte nts Cabl e cover Peripheral screw (Use only ID module 1pcs Screw 2pcs Long type 1pcs 2pcs Dallas KEY r eader) Short type 1 pcs Cabl e clamp 1pcs 2.
13 Tighten the screw to clam p the cable and wiring the cable as shown in the fig. (10)-4. (11) Slide USB cable cover as shown i n the fig. (11)-1. In case of Dallas KEY reader, slide the USB cable cover with care to avoid th e cable from the rib of the USB cable cover as show n in the fig.
3. How to replace the ID module unit (1) Remove Display Unit accordin g to Display Unit Installation. (2) Prepare an ID mod ule unit to be used. * The ID module unit is supplied with 2 p ieces of peri pheral screws, 2 pieces of screws, 1 piece of long cable cover, and 1 piece of short cable cover as accessories.
3. Appendix ■ Specifications [Common Specifications] Environmental condition Item Specification Operating Temperature +5°C – +40°C Operating Humidity 15% RH – 85% RH (no dew) Strage Temperatur.
IO Connector layout (1) Bottom IO Connector layout COM 3 Printer USB2 LAN (Powere d) (2) Rear Display Connector Layout (3) Front IO Connector layout SW & LED USB #5 Soft Switch LAN LED HDD LED Pow.
Outside drawing Main Body 12” Touch Scre en 15” Touch Scre en 17.
[Touch Display Unit: JS-950D ・・・・・ ] Item Specification Size 12.1”: Approx. W320mm x D153mm x H256mm 15”: Approx. W364mm x D153mm x H300mm Mass 12.1”: Approx. 3.4 kg 15”: Approx. 4.4 kg Outside drawing (1) 12.1” resistive TP Display, 12.
[Storage module Unit: JS-950H ・・・・・ ] Item Specification Size Approx. W171mm x D126.5mm x H34mm Mass Approx. 0.8Kg (3.5”), 0.5Kg(2x CF) Outside drawing 3.
[Rear Display Unit: JS-950RD- ・・・ ] Item Specification Size Approx. W216.5mm x D29mm x H90mm Mass Approx. 0.4Kg (2 Lines), 0 .5Kg (4Lines) Outside drawing Rear Display Module 2line, Rear Display.
[2nd Display Unit: JS-950SD- ・・・ ] Item Specification Note: It is not possible to use it together with the Rear Display Unit. Size Approx. W250mm x D72mm x H335mm Mass Approx.
[MSR Unit: JS-950MG-010 ] Item Specification accessories 2 pieces of peripheral screws 2 pieces of screws 1 piece of long cable cover 1 piece of short cable cover Note: MSR, Dallas Key and Fingerpri nt can not be used at the same time. Size Approx. W63mm x D49mm x H140mm Mass Approx.
[Dallas Key Reader Unit: JS-950DP-010 ] Item Specification accessories 2 pieces of peripheral screws 2 pieces of screws 1 piece of long cable cover 1 piece of short cable cover Note: - Work in virtual COM I/F - MSR, Dallas Key and Fingerprint can n ot be used at the same time.
[Fingerprint Sensor Unit: JS-950FS-010 ] Item Specification accessories 2 pieces of peripheral screws 2 pieces of screws 1 piece of long cable cover 1 piece of short cable cover Note: MSR, Dallas Key and Fingerpri nt can not be used at the same time. Size Approx.
■ Cleaning C leaning of outer case Light soil - Wipe case lightly with a dry, soft cloth. Heavy soil - Wipe case lightly with soft cloth pr e-m oistened with very diluted, mild detergent. Lightly wipe case dry with a dry, soft cloth. Cleaning of Display Wipe display gently with a dry, soft cloth to remove l ight dirt and dust.
■ Operation Attention for capacitive touch scr een (1) Do not touch it by finger nail, because c apacitive touch screen can not recognize it. Touch it by finger tip. (2) Do not touch it during startup. It initializ es touch screen during star tup. If it is touched during startup, touch screen is not initialized correc tly.
Specifications and manuals are subject to change without notice. Microsoft and Wind ows are registered trademarks of Microsoft Co rporation in the United State of America and other co untries. Intel and Celeron D are trademarks or registered trademarks of Intel Corporation in the United State of America and other countries.
An important point after buying a device Panasonic JS950D5C020 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Panasonic JS950D5C020 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Panasonic JS950D5C020 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Panasonic JS950D5C020 you will learn all the available features of the product, as well as information on its operation. The information that you get Panasonic JS950D5C020 will certainly help you make a decision on the purchase.
If you already are a holder of Panasonic JS950D5C020, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Panasonic JS950D5C020.
However, one of the most important roles played by the user manual is to help in solving problems with Panasonic JS950D5C020. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Panasonic JS950D5C020 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center