Instruction/ maintenance manual of the product PDP 5000 Palsonic
Go to page of 41
PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL: (02) 9313 7111 FAX: (02) 9313 7555 www.palsonic.com.au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA: 1300 657 888 127CM .
T able of Contents 1 Table of Contents ........................................... Important Safety Precautions ......................... Preparations ................................................... Using the Remote Control .......................
Important Safety Precautions 2 Electrical energy can perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety.
Important Safety Precautions (continued) 3 13. Carefully move ---When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Sudden stops, excessive force and uneven floor surfaces can cause the product to fall from the trolley.
Important Safety Precautions (continued) 4 22. Power source ---This product is intended to be supplied by a listed power supply indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company.
Preparations 5 2 Using the Remote Control Use the remote control by pointing it towards the remote sensor window of the set. Objects between the remote control and sensor window may prevent proper operation. Note: the illustration is for your reference only, the remote sensor may locate differently with different model.
Preparations (continued) 6 1. Connecting the female plug to the AC socket on the unit. 2. Connecting the male plug to the wall outlet as illustrated. Note: This product should be operated only from the type of power source indicated on the marking label.
Preparations (continued) 7 INSTALL the unit in a room where direct light will not fall upon the screen. Total darkness or a reflection on the picture screen may cause eyestrain.
Identification of Controls 8 1. SOURCE Press this button to display SOURCE select menu. 2. MENU Press this button to access the MENU main page. 3. Volume Press the VOL or VOL button to directly increase or decrease the sound volume level. In OSD Menu, press these buttons to adjust the value or setting of each item.
Identification of Controls (continued) 9 1. RS232 terminal For service use only. The user cannot operate the unit through the RS232 terminals. 2. DVI input /Audio in Receives the digital video/audio signals from a set top box or PC. 3. VGA input /Audio in Connect to the VGA/audio output jacks on your PC.
Identification of Controls (continued) 10 1. POWER Turn the unit on or off 2. CH , VOL+/- Use to switch channels or adjust volume; In MENU operation, use CH to select menu item and VOL+/- to adjust selected item. 3. MENU To access the MENU main page 4.
Identifications of Controls (continued) 1 1 To access screen layout select menu 18. PIP display To activate picture in picture To access PIP frame position select menu To access PIP frame size adjusti.
BOTTOM VIEW CONTROL DVI D-SUB COMPONENT INPUT 1 COMPONENT INPUT 2 A V OUTPUT A V INPUT HEADPHONE RF SVHS Connections 12 Carefully check the terminals for position and type before making any connections. The illustration of the external equipment may be different depending on your model.
BOTTOM VIEW CONTROL DVI D-SUB COMPONENT INPUT 1 COMPONENT INPUT 2 A V OUTPUT A V INPUT HEADPHONE RF SVHS Connections (continued) 13 Connect a Camcorder How to connect: Connect the Audio/Video cables between the Audio (L/R)/Video jacks on the unit and camcorder.
BOTTOM VIEW CONTROL DVI D-SUB COMPONENT INPUT 1 COMPONENT INPUT 2 A V OUTPUT A V INPUT HEADPHONE RF SVHS Connections (continued) 14 How to connect a DVD Player using Component Video Connections: Connect the Video cable between the Y, Cb, Cr input jacks on the unit and Y, Cb, Cr output jacks on the DVD player.
BOTTOM VIEW CONTROL DVI D-SUB COMPONENT INPUT 1 COMPONENT INPUT 2 A V OUTPUT A V INPUT HEADPHONE RF SVHS Connections (continued) 15 How to connect: Connect the cable or antenna to the antenna input jack on the DTV receiver. Connect the Video cable between the Y, Pb, Pr input jacks on the unit and Y, Pb, Pr output jacks on the DTV receiver .
BOTTOM VIEW CONTROL DVI D-SUB COMPONENT INPUT 1 COMPONENT INPUT 2 A V OUTPUT A V INPUT HEADPHONE RF SVHS Connections (continued) 16 DVI cable How to connect: Connect a VGA (or DVI) cable between the VGA (or DVI) jack on the PC and the VGA (or DVI) input jack on the unit .
BOTTOM VIEW CONTROL DVI D-SUB COMPONENT INPUT 1 COMPONENT INPUT 2 A V OUTPUT A V INPUT HEADPHONE RF SVHS Connections (continued) 17 Connect a VCR (for recording) or external amplifier External Amplifier How to connect: Connect the Audio/Video cables between the Audio (L/R)/Video jacks on the unit and VCR.
T urning the Unit On and Off 18 Turning the Unit On and Off Turning On Insert the power cord into the wall outlet. Press the Power Switch on the unit. Press the Power button on the remote control. The unit will be turned on and you will be ready to use it's features.
Memorising the Channels 19 Your PDP TV can memorise and store all of the available channels. After the available channels are memorised, use CH to scan through the available stations. Storing Channels in Memory Automatically Press MENU to display the menu main page.
Memorising the Channels (continued) 20 Setting Auto Fine Tune (AFT) Repeat steps 1~4 in [Storing Channels in Memory Automatically] to display search menu page.
Basic Operations 21 Changing Channels Using the Channel Buttons (CH or CH ) Press the CH or CH to change channels. When you press the CH or CH , the unit changes channels in sequence. You will see all the channels that the unit has memorised. You will not see channels that were erased, not memorised or unavailable.
Basic Operations (continued) 22 Select input source signal Press the SOURCE button to access source menu. Press VOL+ or VOL- to select a desired input channel. Press ENTER to confirm and the unit display signal from the selected input channel. A--------VGA, select signal from VGA (5-pin D-sub) terminals.
Setting Channel Options 23 Editing Channel Label Press MENU to display the menu main page. Press VOL+/- repeatedly to display options menu page. Press CH to select tv tuner item. Press VOL+ to enter. Press VOL+ again to display channel menu page. Press CH to select edit labels item.
Setting Picture 24 Customising the Picture Press MENU to display the menu main page. If the picture menu does not display, press VOL+/- repeatedly to display picture menu page. Press CH to select the item you wish to change. Press VOL+/- to adjust the value of the item.
Setting System 25 Setting the Menu Background Press MENU to display the menu main page. Press VOL+/- to display settings menu page. Press CH to select menu background item. Press VOL+/- to select opaque or translucent . Setting Colour and Sound System Press MENU to display the menu main page.
Changing Screen Options 26 Changing the Scaling mode of Image Press MENU to display the menu main page. Press VOL+/- to display window menu page. Press CH to select image size item. Press VOL+/- to select a proper image size. The image size can be selected between: fill all, normal, wide and zoom.
Changing Screen Options (continued) 27 Changing the Position of the Image The unit allows you to adjust the position of the image if it is not well-aligned. Press MENU to display the menu main page. Press VOL+/- to display window menu page. Press CH repeatedly to select h position or v position item.
Setting Sound 28 Using the Preset Audio Mode Press MENU to display the menu main page. Press VOL+/- to display audio menu page. Press CH to select Audio mode item. Press VOL+/- to select a desired Audio mode. Note: You can not access the treble and bass item unless the Audio mode is set to User .
Setting Sound (continued) 29 Using the Auto Volume Each broadcasting station has its own signal conditions, which can make it necessary to adjust the volume every time the channel is changed.
Changing Screen Layout 30 Selecting Screen Layout Using the Layout Menu Press MENU to display the menu main page. Press VOL+/- to display layout menu page. Press CH to select item. Press VOL+ or ENTER to confirm. Using the MODE button Press the MODE button to display the screen layout select menu.
Changing Screen Layout (continued) 31 PIP When this item is selected, one main frame and one PIP frame display on the screen at the same time. Split Screen When this item is selected, the screen will be split into two frames. When this item is selected, one main frame and three scanning frames display on the screen.
PIP Operations 32 Viewing the Picture-in-Picture This unit includes a two-tuner Picture-in-Picture (PIP) feature. This allows you to watch two (2) live broadcasts at the same time with or without an external video source such as a VCR, cable box, etc.
PIP Operations (continued) 33 Press MENU to exit. Changing the Position of the PIP Frame With the PIP frame displaying, press MENU to display the menu main page. Press VOL+/- to display window menu page. Press CH repeatedly to select pip position item.
Adjustment in PC (VGA) Mode 34 With working in VGA mode, this unit allows you to perform many adjustments. Adjusting Picture Press MENU to display the menu main page. If the picture menu does not display, press VOL+/- repeatedly to display picture menu page.
Adjustments in PC (VGA) Mode (continued) 35 Changing the Scaling mode of Image Press MENU to display the menu main page. Press VOL+/- to display window menu page. Press CH to select image size item. Press VOL+/- to select fill all or Normal . Press MENU to exit.
Adjustments in YPbPr Mode 36 Changing the Scaling mode of Image Press MENU to display the menu main page. Press VOL+/- to display window menu page. Press CH to select image size item.
T roubleshooting 37 Before calling for repair service, check the following items for possible remedies to an encountered symptom. Symptoms No power Check item "Ghost" or double images Check that the AC power cord is plugged into the mains socket.
Specifications 38 1429 x 832 x 287 L/R RCA for S-Video or AV x 1 YPbPr/YCbCr (Support HDTV): RCA 75 ohms x 2 1280X 1024 @ 60Hz. 800x600 @ 60Hz,72Hz,75Hz,85Hz; 1280X 1024 @ 60Hz.
Dimensional Drawings 39 1429 777 Design and specifications are subject to change without notice. (Unit: mm) 82.5 744 832 1222.
PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL: (02) 9313 7111 FAX: (02) 9313 7555 www.palsonic.com.au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA: 1300 657 888 604-PH.
An important point after buying a device Palsonic PDP 5000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Palsonic PDP 5000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Palsonic PDP 5000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Palsonic PDP 5000 you will learn all the available features of the product, as well as information on its operation. The information that you get Palsonic PDP 5000 will certainly help you make a decision on the purchase.
If you already are a holder of Palsonic PDP 5000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Palsonic PDP 5000.
However, one of the most important roles played by the user manual is to help in solving problems with Palsonic PDP 5000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Palsonic PDP 5000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
