Instruction/ maintenance manual of the product W7 Packard Bell
Go to page of 18
Packard Be ll EasyNote W7 Se ries (Dragon SN) Disassembl y Manual.
0 Table of C ontents Overv iew 1 Disassem bl y Inst ructions 1 Reassem bly Instructions 1 Required Too ls 1 Hazardous V oltage 2 Avoid E l ectrostat ic Discharge 2 Pow er Supply Un it 2 Battery and AC.
1 Overview This docum ent contains step-by-step disass em bly i nstructions for the Easy Note W 7 (Dragon SN) chass i s. The instruct ions are illust rated w here n ecessary w ith im ages of the part that is be ing rem oved or d isassem bl e d. Packard Bell rese rves the right to m ake changes to the chass is without not i ce.
2 Hazardous Vol tage There is hazar dous voltage p resent inside the com puter when it is connect ed to an AC supply, even w hen the com puter’ s pow er sw itch i s off.
3 WAA R SCHUWING Zorg er voor dat a lle verbind in gen v an en naar de com puter (stroom, m ode m, netw erk, etc) verbroken w orden voordat de behu izing geopend wordt.
4 Battery a nd AC Adapter To rem ove the battery, d o as follow s: 1. Turn off the com puter. 2. Disconn ect the AC ad apter. 3. Rem ove the batte ry. Removing the Hard Disk Drive To rem ove the hard disk d rive, perform the follow in g steps: 1. Remove two screws (2 xA) from the HDD cove r (as sh ow n in Fig.
5 Bottom Panel Perform the follow ing steps to remove the bott om panel: 1. Rem ove nine screw s (9xA) and take aw ay the bottom panel. 2. Rem ove the m e m ory m odule. 3. Lift out th e TV Tuner M i n i-PCI card from its slot. 4. Disconn ect the antenna cable and the tw o data cables.
6 7. Remove the screw s (2xA) from the m ode m . 8. Release the ground cable and tak e aw ay the m ode m . 9. Disconnect the m odem cable from the m ode m. CP U, V GA Module an d Heat S ink To rem ove the heat s in k from the CPU and th e VGA M obi le PC I Express M odul e (MX M) follow the steps below : 1.
7 6. Re m ove the screw from the VGA m odul e (1xT). 7. Pull the VGA m odul e out of the MXM slot. 8. Unlock the CPU socket an d rem ove the CPU. Top Cover Rem ove the top cover by f ollow in g the steps b elow: 1. Slide the button bar to the left to unlock it.
8 6. Disconnect the touchpad f l at cab l e. 7. Re m ove the two hi ng e covers. 8. Disconnect the lid switch conn ector. 9. Rem ove the screw (1xD) and rem ove the lid sw itch unit. Fig. 1 0 Removi ng the keyboa rd flat cabl e . Fig. 1 1 Di sconnect i ng t ouchp ad flat cable Fig.
9 Removing the LC D Panel Asse mbly Follow the steps below to remove the LCD pa nel : 1. Disconnect the two LCD connectors. 2. Release the W ireless antenna ca ble. 3. Rem ove the screws (4xF) from the hinges (see Fig. 13). 4. Take away the LCD assem bl y.
10 Fig. 1 5 LCD di sp lay panel . 10. Disconnect the inverter backlight connector. Fig. 1 6 LCD i nverter backli ght connecter. 11. Rem ove the lower support ing bracket. 12. Take aw ay the LCD display panel and inverter board. 13. Disconn ect the LCD cab le from the inverter b oard.
11 15. Rem ove the screws (3x D, 1xA) from the l eft L CD bracket. The sam e goes for the right bracke t. Fig. 1 8 LCD di sp lay cabl e. 16. Take away the top, left and right bracket from the LCD display pane l. 17. Rem ove the screws (2xD) holding the w ireles s antenna and take away the antenna.
12 Optical Di sk Drive To rem ove the optica l disk dr ive, fo llow the steps be lo w : 1. Remove the screws (2xB) and push t he opt i cal d isk d rive out of i ts bay. Fig. 2 0 The sc re ws o f the op ti cal di sk dr i ve. 2. Rem ove the screw s (2xK) from the side ODD bracket and remove it.
13 Bottom Base Asse mbly Disassem bl e the bottom base assembly as fo llows: 1. First remove the screw s (4XA) from the top cover. 2. Then rem ove the screws (4xJ). No te: Mak e su re tha t du ring re -as se mbl y the c lips o f the top co ve r loc k i nto plac e be fore fas tenin g the scre ws.
14 4. Re m ove the screws from the rear (2x B). 5. Remove bottom cover from base assem bl y. 6. Disconnect the s ubwoofer conn ector. 7. Rem ove the screws (2x G) and lift out the s ubw oofer assem bl y. 8. Re m ove the rubber stab ili z ers (2x M) fro m the subwoofer assem bl y.
15 8. Take away the m ain board. 9. Partially rem ove the foil over the to uchpad. 10. Disconnect the touchpad cable. 11. Remove the screws (3xB) and rem ove the heat plate. 12. Push out the touchpa d assem bly. Fig. 2 6 The mai n board and speake rs .
16 Notice The inform ation in this guide is subj ect to cha nge without notice. This guide c ontains inform atio n protect ed by copyr ig ht. No part of th is guide m ay be photocop ied or reproduc ed in any f orm or by any m eans without pr ior w ritten cons ent from NEC Computers Intern ational BV.
An important point after buying a device Packard Bell W7 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Packard Bell W7 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Packard Bell W7 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Packard Bell W7 you will learn all the available features of the product, as well as information on its operation. The information that you get Packard Bell W7 will certainly help you make a decision on the purchase.
If you already are a holder of Packard Bell W7, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Packard Bell W7.
However, one of the most important roles played by the user manual is to help in solving problems with Packard Bell W7. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Packard Bell W7 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
