Instruction/ maintenance manual of the product ORION MaxxBass Orion Car Audio
Go to page of 17
Maxx Bass ®.
T ABLE OF CONTENTS Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Caution . . . . . . . . . . . . . . . .
CONGRA TULA TIONS Thank you for choosing Orion audio equipment. At Orion we proudly design, engineer and manufacture audio products for aftermarket car audio. Our award winning engineering team utilizes innovative technology to consistently deliver Absolutely State of the Art performance, sound quality , reliability , and value.
recommended in two configurations. (Please see Wiring Configurations for more details.) 1) Front Stereo Configuration One Maxx Bass ® Processor is used between the front channel source and front speaker amplifier to increase the bass response on only the front speakers.
This is accomplished using the science of psychoacoustics on how we perceive sound. By building audio systems optimized for how we hear sound, significant performance improvements can be obtained. This is analogous to designing and building televisions that only display red, green and blue dots.
5 MAXX BASS ® SIGNAL FLOW FEA TURES Selectable Maxx Bass ® Frequency Setting of 60Hz and 80Hz Green LED clip/Red LED power indicator signal Gold 2 Channel in/2 channel buf fered full-ran.
SPECIFICA TIONS Frequency 20hz-20kHz Signal-to-Noise Ratio >85dB Separation 65dB @ 1kHz Crossover Slope 24dB/octave Input Impedance 20,000 Ohms Input Sensitivity variable, 300mV to 3V peak to peak .
MAXX BASS ® OUTLINE AND DIMENSIONS MI NM A X I N TEN SI TY MI NM A X OU T P U T I NP UT MI NM A X 80H z 60H z ON OF F F RE Q UE NCY CROS S O VER I NP UT OUT P UT P O W E R RE M OT E G ND RE M +12V RE M OUT ( 11. 5 cm ) ( 6. 3 cm ) ( 14 cm ) ( 3 cm ) 1.
WIRING CONFIGURA TIONS The Maxx Bass ® Processor is recommended in two different configurations. 1. Front Ster eo Configuration The figure below illustrates the wiring for a front stereo configuration.
2. Dual Stereo Configurations For systems without rear subwoofers, the user may prefer to use two Maxx Bass ® Processors, one for the front speakers and one for the rear speakers. The units should be wired between the in-dash CD Receiver and the power amplifiers as shown below .
The ground wire should be of the same gauge wire as the power wire. As a rule of thumb, use as short length of wire as possible. Find a location near the Maxx Bass ® Processor that is metal ( the floor is ideal) and clean an area about the size of a quarter to bare metal.
INPUT T o use Speaker Level Inputs (common ground head units only), connect RCA plugs to the front or rear speaker leads as shown. NOTE: It is important to connect an input signal to both RCA input jacks if a stereo amplifier is used, otherwise the connected channel receives full range and the disconnected channel will receive only the harmonics.
MAXX BASS ® PROCESSOR SETTINGS T o achieve proper performance it is important to set or tune the settings on the Maxx Bass ® Processor to the final system. This section recommends initial settings and the users can then further adjust these for optimal listening.
TROUBLESHOOTING NO SOUND Is the POWER LED lit? YES NO Check Input cables for signal by Check power and remote Connecting them straight to the turn-on wire for voltage. Subwoofer amplifier . Make sure the ground wire is Secure. ANY SOUND NOW? YES NO Problem is in the Crossover .
OPPOSITE CHANNEL SAME CHANNEL Reverse RCAs to head unit Problem is in the Crossover . (Check Balance Control) See your local Authorized Orion dealer . SOUND IS NOW IN OPPOSITE CHANNEL SAME CHANNEL Problem is in the head unit. Problem is in the RCA cables.
15.
W arranty LIMITED TWO YEAR CONSUMER WARRANTY : Directed Electronics, Inc. promises to the original purchaser , to replace this product should it prove to be defective in workmanship or material under .
An important point after buying a device Orion Car Audio ORION MaxxBass (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Orion Car Audio ORION MaxxBass yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Orion Car Audio ORION MaxxBass - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Orion Car Audio ORION MaxxBass you will learn all the available features of the product, as well as information on its operation. The information that you get Orion Car Audio ORION MaxxBass will certainly help you make a decision on the purchase.
If you already are a holder of Orion Car Audio ORION MaxxBass, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Orion Car Audio ORION MaxxBass.
However, one of the most important roles played by the user manual is to help in solving problems with Orion Car Audio ORION MaxxBass. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Orion Car Audio ORION MaxxBass along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
