Instruction/ maintenance manual of the product HP-2300 Orion Car Audio
Go to page of 29
HP-2300 HP-2400 HP-2600 HP-4600 HP-2300 HP-2400 HP-2600 HP-4600.
CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 What’ s in the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION Thank you for your purchase of Orion's amplifier . Each Orion amplifier is designed to be the leader in its class offering ease of use, advanced features, and the most power . Orion ampli- fiers are designed as the best affordable high end car audio amplifier money can buy .
RECORD YOUR SERIAL NUMBER AND DA TE T o ensure your warranty (see back cover), please record the following information regard- ing your new amplifier .
HP-2300, HP-2400, HP-2600 Connections 1. A TC Fuse - A TC fuses protect the amplifier against internal electrical damage and is meant to protect the amplifier only . All other power connections should be fused at the source. The HP-2300 has (1) 20-amp, the HP-2400 has (1) 30-amp, the HP-2600 has (2) 20-amp fuses.
5 © 2005 Directed Electr onics, all rights reserved 2. RCA Input Channels 1 through 4 - accepts RCA input from a head unit, pream- plifier , or equalizer . These inputs are configured by the Input Mode switch posi- tion (refer to item 11 below). 3. RCA Line Output - provides easy connection to additional amplifiers.
6 © 2005 Directed Electr onics, all rights reserved supply a remote turn on signal. DO NOT connect this terminal to constant (+) 12 volt. 4. GND - power return connection. Connect this terminal directly to the sheet metal chassis of the vehicle, using the shortest wire necessary to make this connection.
7 © 2005 Directed Electr onics, all rights reserved CEA SPECIFICA TIONS H H P P - - 2 2 3 3 0 0 0 0 Power Output: 50 Watts RMS x 2 at 4 ohms and < 1% THD+N Signal to Noise Ratio: -70 dBA (reference 1 Watt into 4 ohms) Additional Power Output: 75 Watts RMS x 2 at 2 ohm at 14.
8 © 2005 Directed Electr onics, all rights reserved SPECIFICA TIONS 1. Continuous 4 W load 20Hz to 20kHz, < 1% THD, with input voltage at 14.4VDC. 2.
9 © 2005 Directed Electr onics, all rights reserved SPECIFICA TIONS—CONTINUED 1. Continuous 4 W load 20Hz to 20kHz, < 1% THD, with input voltage at 14.
10 © 2005 Directed Electr onics, all rights reserved AMPLIFIER SETTINGS Signal Input and Output Configurations Depending on your model, the input section of the amplifier consists of gain controls, high pass and low pass crossovers controls, Intelli-Bass control and RCA inputs and outputs.
11 © 2005 Directed Electr onics, all rights reserved High-Pass Crossover When the switch is to the left (FULL position), the high-pass crossover is bypassed. When the switch is in the middle (HIGH position), the high-pass crossover is active. The high-pass crossover is continuously variable from 50Hz to 500Hz.
12 © 2005 Directed Electr onics, all rights reserved Infinite Baffle Example High-Pass Set at 30Hz By removing low frequency signal that the woofer cannot produce, the woofer can play its capable range louder . The first example is an infinite baffle situation.
13 © 2005 Directed Electr onics, all rights reserved Sealed Example High-Pass Set at 30Hz In this example, the frequency has been increased to 30 Hz. Up to 6 dB of boost is capable at this frequency . With +6dB of boost, the woofer has more output down to 23 Hz.
14 © 2005 Directed Electr onics, all rights reserved AMPLIFIER WIRING NOTE: Power and speaker connections to the amplifier should be made prior to final positioning and mounting of the amplifier in the vehicle. Power Connections ● Orion HP-2300 Fuse Size: 1 x 20 AMP A TC.
15 © 2005 Directed Electr onics, all rights reserved Speaker Connections HP-2300, HP-2400, and HP-2600 One Channel/T wo Channel Configuration The Orion HP-2300/2400/2600 amplifiers offer two positive and two negative output termi- nals for ease of connecting channel 1 and/or 2 outputs to the speakers.
16 © 2005 Directed Electr onics, all rights reserved Three Channel (Channel 1, Channel 2, Bridged) ● Channels 1 and 2 are configured for two-channel stereo operation. ● Front channel lowest recommended impedance is 2 W stereo. ● The third output is configured for a single channel bridged output.
17 © 2005 Directed Electr onics, all rights reserved Speaker Connections HP-4600 The Orion HP-4600 amplifier offer four positive and four negative output terminals for ease of connecting channel 1, 2, 3, and 4 outputs to the speakers. The amplifier is stable to 2 W .
18 © 2005 Directed Electr onics, all rights reserved Three Channel Stereo/Bridged Configuration ● Channels 1/2 are configured for 2-channel stereo operation. ● Channel 1/2 lowest recommended impedance is 2 W stereo. ● Channels 3/4 are configured for a single channel bridged output.
T ri-Mode Six Channel Configuration ● Lowest recommended impedance is 2 W stereo and 4 W bridged mono. ● Front and rear outputs must be set for full range operation. ● Passive crossovers must be used on all components and frequencies must not overlap.
20 © 2005 Directed Electr onics, all rights reserved AMPLIFIER INST ALLA TION Choosing Mounting Locations The location of your amplifier will depend on several important issues. Due to the low pro- file size of the Orion amplifiers, there are many possible installation locations that will yield satisfactory amplifier performance.
21 © 2005 Directed Electr onics, all rights reserved Power for systems with a single amplifier can be supplied by most automotive electrical sys- tems. Systems with multiple amplifiers may require a higher capacity battery , alternator or the use of a storage capacitor .
22 © 2005 Directed Electr onics, all rights reserved Step 8 Connect power wires to the amplifier (ground first, then 12 V(+) and REM). Do not connect the battery at this time. Step 9 Connect the RCA and speaker wires to the amplifier . Check the quality of your speakers and signal connections.
23 © 2005 Directed Electr onics, all rights reserved Step 7 If the output is clear and undistorted, continue to the Adjusting the Sound of the System section of this manual. Adjusting the Sound of the System Once you have checked the system's operation, adjust the sound of the system.
24 © 2005 Directed Electr onics, all rights reserved T roubleshooting Tips Symptom Probable Cause Action T o T ake No output Low or no remote turn-on Check remote turn-on voltage at voltage amplifier and repair as needed. Fuse blown Check power wire's integrity and check for speaker shorts.
Symptom Probable Cause Action T o T ake Distorted output Internal crossover not set Readjust crossovers. Refer to the properly for speakers Internal Crossover Configuration section of this guide for detailed instructions. Speakers are blown Check system with known work ing speakers and fix or replace as needed.
26 © 2005 Directed Electr onics, all rights reserved.
NOTES ____________________________________________________ ____________________________________________________ ____________________________________________________ ___________________________________.
W arranty LIMITED TWO YEAR CONSUMER WARRANTY : Directed Electronics promises to the original purchaser , to replace this product should it prove to be defective in workmanship or material under normal.
An important point after buying a device Orion Car Audio HP-2300 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Orion Car Audio HP-2300 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Orion Car Audio HP-2300 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Orion Car Audio HP-2300 you will learn all the available features of the product, as well as information on its operation. The information that you get Orion Car Audio HP-2300 will certainly help you make a decision on the purchase.
If you already are a holder of Orion Car Audio HP-2300, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Orion Car Audio HP-2300.
However, one of the most important roles played by the user manual is to help in solving problems with Orion Car Audio HP-2300. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Orion Car Audio HP-2300 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
