Instruction/ maintenance manual of the product 2002 Orion Car Audio
Go to page of 18
.
CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 What’ s in the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION Thank you for your purchase of Orion's 2002 or 3002 amplifier . Each Orion amplifier is designed to be the leader in its class offering ease of use, advanced features, and the most power . Orion amplifiers are designed as the best affordable high end car audio amplifier money can buy .
LIMITED TWO-YEAR CONSUMER WARRANTY Directed Electronics, Inc. promises to the original purchaser , to replace this product should it prove to be defective in workmanship or material under normal use, .
SPECIFICA TIONS 1. All channels driven, continuous 4 W load 20Hz to 20kHz, < 0.05% THD, with input voltage at 13.8VDC. 2. All channels driven, continuous 2 W load 20Hz to 20kHz, < 0.
END P ANEL LA YOUT 1. Power LED - when lit indicates that the amplifier is on. 2. Stereo/Mono Switch - configures the amplifier for one or two inputs. 3. RCA Inputs - accepts RCA input from a source unit, preamplifier , or equalizer . 4. Gain Control - continuously adjusts from 200mV to 5V for full power output.
AMPLIFIER SETTINGS Stereo / Mono Input Configuration The STEREO / MONO switch allows the Orion 2002 and 3002 amplifiers to use a single RCA or high-level input to feed signal to both the right and left channels of the amplifier . When the switch is to the right (MONO position), signal from the left input is routed to the right channel.
AMPLIFIER WIRING Power Connections ● Orion 2002 Fuse Size: (1) 25 AMP ● Orion 3002 Fuse Size: (1) 30 AMP ● Minimum 8 AWG power and ground cable is recommended for acceptable per- formance. ● Fuse power wire prior to wire passing through panels or near sharp edges and less than 18" from battery .
Summed Bridged Configuration ● Lowest recommended impedance is 4 W bridged mono. ● Mono or stereo input can be used for this configuration. ● Outputs can be configured for high-pass, low-pass, or full range operation. ● Output is configured as summed bridged which is ideal for subwoofer applications.
T ri-Mode Three Channel Configuration ● Lowest recommended impedance is 2 W stereo and 4 W bridged mono. ● Stereo operation must be used. ● Outputs must be configured for full range operation ● Output is configured stereo and summed bridged. ● Passive crossover frequencies must not overlap.
amplifier with as much clearance as possible. This type of mounting will yield the best cool- ing due to the convection effect of the amplifier chassis.
● Pliers (standard and needle nose) ● Reference CD with 1 kHz Sine Wave at 0dB level (all bits high) ● RT A (real time analyzer) ● Soldering iron and solder ● Utility knife ● Wire brush or.
SET UP AND TROUBLESHOOTING T esting the System After you have completed the installation, you need to test the system. This will help ensure years of trouble-free operation. Please refer to the listed steps below when testing the sound of your Orion system.
nels. Step 6 T urn up the level control corresponding to the tweeter output until you hear slight distortion and turn back the level control slightly for an undistorted output. Depending on your system the midrange and tweeter output may be on the same output channels.
T roubleshooting Tips Symptom Probable Cause Action T o T ake No output Low or no remote turn-on Check remote turn-on voltage at voltage amplifier and repair as needed. Fuse blown Check power wire's integrity and check for speaker shorts. Fix as needed and replace fuse.
Symptom Probable Cause Action T o T ake Distorted output Internal crossover not set Readjust crossovers. Refer to the properly for speakers Internal Crossover Configuration section of this guide for detailed instructions. Speakers are blown Check system with known work ing speakers and fix or replace as needed.
NOTES ____________________________________________________ ____________________________________________________ ____________________________________________________ ___________________________________.
W arranty LIMITED TWO YEAR CONSUMER WARRANTY : Directed Electronics, Inc. promises to the original purchaser , to replace this product should it prove to be defective in workmanship or material under .
An important point after buying a device Orion Car Audio 2002 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Orion Car Audio 2002 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Orion Car Audio 2002 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Orion Car Audio 2002 you will learn all the available features of the product, as well as information on its operation. The information that you get Orion Car Audio 2002 will certainly help you make a decision on the purchase.
If you already are a holder of Orion Car Audio 2002, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Orion Car Audio 2002.
However, one of the most important roles played by the user manual is to help in solving problems with Orion Car Audio 2002. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Orion Car Audio 2002 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
