Instruction/ maintenance manual of the product BAR623 Oregon Scientific
Go to page of 19
1 EN CONTENTS Contents ................................................................ 1 Introduction ........................................................... 2 Product Overview ................................................. 2 Front View ......
2 EN INTRODUCTION Thank you for selecting the Oregon Scientific™ Wireless W eather Station (BAR623P / BAR623PU). This device bundles precise time keeping with a projection clock, weather forecast, and indoor and outdoor temperature monitoring features into a single tool you can use from the convenience of your home.
3 EN BACK VIEW 1. Projector FOCUS knob 2. Projector IMAGE ROT A TION knob 3. PROJECTION ON / OFF switch 4. AC / DC adaptor plug cover 5. Battery compartment (cover off) 6. SEARCH button to locate the remote sensor 7. MEM : View current, maximum, and minimum temperature readings 8.
4 EN LCD DISPLA Y 1. Weather display 2. Radio Frequency (RF) reception icon 3. Alarm activated 4. Alarm setting 5. T ime 6. Indoor temperature 7. Low battery icon for main unit 8. ° C / ° F (Outdoor temperature) 9. Sensor signal 10. Low battery icon for sensor 11 .
5 EN REMOTE SENSOR (THN122N) 1. Wall mount hole 2. RESET hole 3. CHANNEL number ( 1-3 ) 4. Battery compartment (Battery compartment cover not shown) 1.
6 EN UNIT LOCA TION Main Indoor T emperature Area Remote Outdoor T emperature Area Installing the batteries: GETTING ST ARTED BA TTERIES Batteries are supplied with this product: Main unit 3 x UM-3 (AA) 1.
7 EN AC ADAPTOR The main unit has a 4.5V AC / DC adaptor with jack, which provides continuous clock / temperature projection. Inserting the adaptor: CHANGE SETTINGS To change, time, calendar and language settings: 1. Press and hold MODE for 2 seconds to enter setting mode.
8 EN Installing the batteries: REMOTE SENSOR (THN122N) This product is shipped with a THN122N Thermometer Sensor that collects T emperature data. The main unit can be connected to only 1 remote sensor. SETUP SENSOR 1. Open the remote sensor battery compartment with a small Phillips screwdriver.
9 EN For best results: • Insert the batteries and select the channel before you mount the sensor. • Place the sensor out of direct sunlight and moisture.
10 EN To force a manual search for clock signals, press and hold for 2 seconds. If no signal is found, check the batteries. TURN CLOCK ON / OFF Perform this step if you cannot receive clock signals. Press and hold for 2 seconds. Then, manually set the clock following the “Set Clock” instructions (below).
11 EN SET CLOCK / CALENDAR Y ou only need to do this if you have disabled the clock feature (for example, if you are too far from or cannot receive a signal). 1. Press and hold MODE for 2 seconds. The Clock Area will blink. 2. Select the hour, minute, year, month, day, and day of the week language.
12 EN SILENCE ALARM When the alarm time is reached, the crescendo alarm will sound for 2 minutes. T o silence the alarm: • Press SNOOZE to silence it for 8 minutes. OR •P ress any key except SNOOZE to mute the alarm and activate it again after 24 hours.
13 EN MOON PHASE The Calendar must be set for this feature to work, see “Set Clock” section. • Press or to view the moon phase for the next or previous day.
14 EN RESET SYSTEM The RESET button is located in the main unit battery compartment. Press RESET when you change the batteries and whenever performance is not behaving as expected (for example, unable to establish radio frequency link with remote sensor or clock).
15 EN • Never immerse the product in water . This can cause electrical shock and damage the product. • Do not subject the main unit to extreme force, shock, or fluctuations in temperature or humidity. • Do not tamper with the internal components.
16 EN SPECIFICA TIONS MAIN UNIT DIMENSIONS L x W x H 92 x 167 x 53 mm (3.6 x 6.6 x 2.1 inches) W eight 228 grams (8.04 ounces) without battery REMOTE SENSOR DIMENSIONS L x W x H 92 x 60 x 20 mm (3.
17 EN Calendar DD / MM; weekday in 5 languages (E, D, F, I, S) Alarm Single alarm with 2-minute crescendo and 8-minute Snooze Projector Outdoor temperature and time POWER Main unit batteries 3 x UM-3 (AA) 1.5V Sensor batteries 2 x UM-4 (AAA) 1.5V AC / DC adaptor 4.
18 EN EC-DECLARA TION OF CONFORMITY This product contains the approved transmitter module that complies with the essential requirements of Article 3 of the R&TTE 1999 / 5 / EC Directive, if used as intended and the following standards have been applied: Safety of information technology equipment (Article 3.
19 EN W ireless W eather Station Model: BAR623P / BAR623PU User Manual BAR623P_EN_R2.p65 7/27/04, 12:40 AM 19.
An important point after buying a device Oregon Scientific BAR623 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Oregon Scientific BAR623 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Oregon Scientific BAR623 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Oregon Scientific BAR623 you will learn all the available features of the product, as well as information on its operation. The information that you get Oregon Scientific BAR623 will certainly help you make a decision on the purchase.
If you already are a holder of Oregon Scientific BAR623, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Oregon Scientific BAR623.
However, one of the most important roles played by the user manual is to help in solving problems with Oregon Scientific BAR623. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Oregon Scientific BAR623 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
