EN
Olympus logo
Official user manual

Olympus PT-E02

284 pages·17.3 MB·Camera Accessories·PDF·ENITNL
Olympus PT-E02
Table of Contents 56 sections Disclaimer · Please read the following before using the product · For safe use · WARNING · … ShowHide
Disclaimerp.1Please read the following before using the productp.1For safe usep.1WARNINGp.1Batteriesp.3For Prevention of Water Leakage Accidentsp.3Handling the Productp.4Contentsp.51. Preparationsp.7デジタルカメラ 用 防水プロテクタp.7Names of the partsp.8How to hold the Casep.10How to Press the Shutterp.10How to Use the Mode Dialp.10How to use the zoom dialp.11PPO-E01p.11PPO-E03 +PER-E01p.11How to control the power switch leverp.12p.12p.12How to control the eyepiece shutter leverp.12Removing the TTL cable connector capp.13Cleaning the TTL connectorp.13How to connect the hot shoe cablep.14How to attach or remove the camera from the camera tablep.142. Advance Check of the Casep.15Advance test before usep.15Check the waterproof parts of the Casep.15Preliminary testp.153. Installing the digital camerap.16Battery Confirmationp.16Check the remaining number of picturesp.16Remove the hand strap and lens cap from the digital camerap.16Remove the filter from the digital camerap.16Compatible digital camerap.17Checking camera operationp.17Attaching the optional zooming/focusing gear(PPZR-E03/04/05) to the lensp.18Attach the digital camera to the camera tablep.19Insert silica gelp.22Visual Inspectionp.24Final Testp.254. Underwater Shootingp.26How to use the hand strapp.26Cautions when using the flashp.275. Handling After Shootingp.276. Maintaining the Waterproof Functionp.30How to Apply Grease to the O-ringp.31Maintenance of the TTL Connector Capp.327. Appendixp.33PER-E01 EC-14p.36Specificationsp.37MEMOp.38Mode d’emploip.40Caisson étanchep.40Pour l’appareil photo numérique E-330 PT-E02p.40Frp.40
Page 1 of the Olympus PT-E02 user manual — WARNING
Page 1 · click to enlarge
Page 1
  • Thank you for buying the Underwater Case PT-E02.
  • Please read this instruction manual carefully and use the product safely and correctly.
  • Please keep this instruction manual for reference after reading it.
  • Wrong use may cause damage to the camera on the inside from water leakage, and

repair may not be possible. ■Before use, perform an advance check as described in this manual.

Disclaimer

  • Unauthorised copying of this manual in part or in full, except for private use, is prohibited. Unauthorised reproduction is strictly prohibited.
  • OLYMPUS IMAGING CORP. shall not be responsible in any way for lost profits or any claims by third parties in case of any damage occurring from incorrect use of this product.
  • OLYMPUS IMAGING CORP. shall not be responsible in any way for damage, lost profits, etc. caused by the loss of image data due to defects, disassembly, repair or modification of this product by people, other than third parties specifically authorised by OLYMPUS IMAGING CORP. or for other reasons.

Please read the following before using the product

  • This product has been precision-crafted from high quality polycarbonate. When used correctly, it lets you take photographs safely up to a water pressure equivalent to a depth of 60 metres.
  • To ensure correct and safe use of the case, please read all instructions on handling and carrying out the system check as well as care, maintenance and storage of the case.
  • The Case must be used in combination with the separately available Waterproof Port.
  • OLYMPUS IMAGING CORP. shall in no way be responsible for damage caused by water to the camera contained in the case.
  • OLYMPUS IMAGING CORP. shall not pay any compensation for accidents (injuries or material damage) that happen during the use of this product.
  • Before use, be sure to read the precautions printed on the package.

For safe use

This instruction manual uses various pictographs for correct use of the product and to prevent danger to the user and other persons as well as property damage. These pictographs and their meanings are shown below.

This indicates contents for which the possibility of human death or severe injury in case of handling under disregard of this indication can be assumed.

WARNING

This indicates contents for which the possibility of human injury or the possibility of material damage in case of handling under disregard of this indication can be assumed.

Page 2 of the Olympus PT-E02 user manual — WARNING
Page 2 · click to enlarge
Page 2

WARNING

1. Keep this product out of the reach of babies, infants, and children. There is the possibility of occurrence of the following types of accidents. Injury by dropping onto the body from a height. Injury from parts of the body getting caught in parts which open and close. Swallowing of small parts. Please consult a physician immediately if any parts have been

swallowed. 2. Do not store with a battery in the digital camera housed in this product. Storage with a battery inserted may lead to leakage of the battery liquid and fire. 3. The Case must be used in combination with the separately available Waterproof Port. Remember that the Case cannot be used without the Waterproof Port. 4. If leakage of water should occur with a camera installed in this product, quickly remove the battery from the camera. There is the possibility of ignition and explosion from generation of hydrogen gas. 5. This product is made of resin. There is the possibility that injuries may be caused when it becomes broken because of strong impact with a rock or other hard objects. Please handle with sufficient care. 6. The silica gel and the grease for silicone O-rings for this product are not edible.

1. Do not disassemble or modify this product. This may cause water leakage or trouble. In case of disassembly or modification by persons other than those appointed by OLYMPUS IMAGING CORP., the guarantee shall not apply. 2. Do not place this product at locations with abnormally high or abnormally low temperatures or at locations with extreme temperature changes. The product may deteriorate. 3. Opening and closing at locations with much sand, dust, or dirt may impair the waterproof characteristic and cause water leakage. This should be avoided. 4. This product has been designed and manufactured for use at a water depth within 40 m. Please note that diving to a depth in excess of 60 m may cause permanent deformation or damage to the Case and the camera inside the Case or may lead to water leakage. 5. Rough handling, such as jumping into the water with the case in your hand or in an outside pocket or throwing the case into the water, etc. could lead to water leakage. Please always take care when using the case. 6. If the camera contained in the case becomes wet because of water leakage, etc., immediately wipe off all moisture and check the camera is working correctly. 7. Before travelling by air, please make sure you remove the O-ring, otherwise the difference in air pressure may make it impossible to open the case. 8. To ensure safe and trouble-free handling and operation of the digital camera in this product, please read the camera’s instruction manual carefully. 9. When sealing this product, please take care to ensure no foreign matter such as sand, dirt or hair are on the O-ring or contact surfaces. 10. The digital camera’s built-in flash cannot be used when the Case is being used. To avoid damaging the Case or the digital camera, do not attempt to load the digital camera into the Case when the flash is extruded from the camera. 11. When using this Case, you cannot adjust the angle of the LCD monitor on the digital camera. Any attempt to forcefully close this Case when the angle of the LCD monitor angle has been modified could result in damage to the Case or the digital camera.

Page 3 of the Olympus PT-E02 user manual — For Prevention of Water Leakage Accidents
Page 3 · click to enlarge
Page 3

Batteries

  • Use an exclusive lithium-ion battery (Olympus BLM-1) designed for digital cameras.
  • Keep the battery's contacts away from damp or humidity; otherwise this could impair performance and/or cause accidents.
  • For additional battery cautions, refer to your digital camera's instruction manual.

For Prevention of Water Leakage Accidents

When water leakage occurs while this product is being used, repair of the camera housed in this product may become impossible. Please observe the following cautions for use.

1. When sealing this product, make sure that no hairs, fibers, sand particles or other foreign matter stick not only to the O-ring, but also to the contact surface. Even a single hair or a single grain of sand may cause water leakage. Please check with special care.
Olympus PT-E02 — For Prevention of Water Leakage Accidents diagram (page 3)
Fig. 1 · For Prevention of Water Leakage Accidents

Examples for foreign matter sticking to the O-ring

2. The O-ring is a consumption product. Please replace it at least once a year by new one. Also perform maintenance for every use. 3. Deterioration of the O-ring will progress according to the use conditions and the storage conditions. Immediately replace the O-ring by a new one if it is damaged, shows cracks, or has lost its elasticity. 4. At the time of O-ring maintenance, clean the inside of the O-ring groove and confirm the absence of dirt, dust, sand, and other foreign matter. 5. Apply the specified silicone O-ring grease to the O-ring. 6. The waterproof function is not effective when the O-ring is not installed correctly. When installing the O-ring, take care that it does not project from the groove and that it is not twisted. Also, when sealing the Case, close the lid after confirming that the O-ring has not come out of the groove. 7. This product is an airtight construction made of plastic (polycarbonate). When it is left for a long time in a car, on a boat, at the beach, or at other places reaching a high temperature, or when it is subjected for a long time to uneven external force, it may be deformed and the waterproof function may be lost. Pay sufficient attention to temperature control. Also do not place heavy objects onto the product during storage or transport, and avoid unreasonable storage. 8. When the O-ring contact surface is pressed strongly from the outside of the Case, or when the Case is twisted, the waterproof function may be lost. Take care not to exert excessive force. 9. Please be sure to perform the advance test and the final test each time before using the case. 10.If you should notice drops of water or other signs of water leakage while taking pictures, immediately stop the dive, remove any water from the camera and the product, test according to the item "Final check", and confirm whether leakage has occurred or not.

Hair Fibers Fibers

Page 4 of the Olympus PT-E02 user manual — Handling the Product
Page 4 · click to enlarge
Page 4

Handling the Product

  • Use or storage of the product at the following locations may cause defective operation, defects, trouble, damage, fire, internal clouding, or water leakage. Always avoid these locations. Places where high temperatures exist, such as in direct sunlight, in a closed vehicle, etc.,
  • and/or where extreme differences in temperatures exist. Places where there is a lot of dust. Places where there are open fires. Places subject to vibrations. Places where volatile chemicals are stored or used. Water deeper than 60 meters.
  • This product is made of polycarbonate resin with excellent impact resistance, but it may be damaged by scraping against rocks etc. It also may break when it hits hard objects or is dropped.
  • This product is not a case to soften impacts to the camera inside the product. When this product with a digital camera inside it is subjected to impacts or heavy objects are placed onto it, the digital camera may become damaged. Please handle the product with sufficient care.
  • When the product is not used for a long time, the waterproof performance may drop because of deterioration of the O-ring etc. Before use, always perform the advance test and the final check.
  • Do not apply excessive force to the port mount, TTL cable connector, tripod socket, etc.
  • Do not use the following chemicals for cleaning, corrosion prevention, prevention of fogging, repair or other purposes. When these are used for the Case directly or indirectly (with the chemicals in vaporized state), they may cause cracking under high pressure or other problems.

Chemicals which cannot be used Explanation

Volatile organic solvents, chemical detergents

Do not clean the Case with alcohol, gasoline, thinner or other volatile organic solvents or with chemical detergents etc. Pure water or lukewarm water is sufficient.

Do not use anticorrosion agents. The metal parts use stainless steel or brass, and washing with pure water is sufficient.

Do not use commercial defogging agents. Always use the specified desiccant silica gel.

Grease other than specified silicone grease

Use only the specified silicone grease for the silicone O-ring, as otherwise the O-ring surface may deteriorate and water leakage may be caused.

Do not use adhesive for repairs or other purposes. When repair is required, please contact a dealer or a service station of our company.

  • Do not perform operations other than specified in this instruction manual, do not remove or modify parts other than specified, and do not use parts other than specified. Any troubles in taking pictures or with the equipment resulting from the above actions shall be outside the guarantee.
  • OLYMPUS IMAGING CORP. shall be in no way responsible for accidents involving immersion of a digital camera in water.
  • OLYMPUS IMAGING CORP. shall not pay any compensation for accidents (injury or material damage) at the time of use.

Anticorrosion agent · Commercial defogging agents · Adhesive

Page 5 of the Olympus PT-E02 user manual — Table of Contents
Page 5 · Contents
Contents

Contents

Disclaimerp.1Please read the following before using the productp.1For safe usep.1WARNINGp.1Batteriesp.3For Prevention of Water Leakage Accidentsp.3Handling the Productp.4Contentsp.51. Preparationsp.7デジタルカメラ 用 防水プロテクタp.7Names of the partsp.8How to hold the Casep.10How to Press the Shutterp.10How to Use the Mode Dialp.10How to use the zoom dialp.11PPO-E01p.11PPO-E03 +PER-E01p.11How to control the power switch leverp.12p.12p.12How to control the eyepiece shutter leverp.12Removing the TTL cable connector capp.13Cleaning the TTL connectorp.13How to connect the hot shoe cablep.14How to attach or remove the camera from the camera tablep.142. Advance Check of the Casep.15Advance test before usep.15Check the waterproof parts of the Casep.15Preliminary testp.153. Installing the digital camerap.16Battery Confirmationp.16Check the remaining number of picturesp.16Remove the hand strap and lens cap from the digital camerap.16Remove the filter from the digital camerap.16Compatible digital camerap.17Checking camera operationp.17Attaching the optional zooming/focusing gear(PPZR-E03/04/05) to the lensp.18Attach the digital camera to the camera tablep.19Insert silica gelp.22Visual Inspectionp.24Final Testp.254. Underwater Shootingp.26How to use the hand strapp.26Cautions when using the flashp.275. Handling After Shootingp.276. Maintaining the Waterproof Functionp.30How to Apply Grease to the O-ringp.31Maintenance of the TTL Connector Capp.327. Appendixp.33PER-E01 EC-14p.36Specificationsp.37MEMOp.38Mode d’emploip.40Caisson étanchep.40Pour l’appareil photo numérique E-330 PT-E02p.40Frp.40
Page 7 of the Olympus PT-E02 user manual — デジタルカメラ 用 防水プロテクタ
Page 7 · click to enlarge
Page 7

1. Preparations

Check the contents of the package.

Check that all accessories are in the box. Contact your dealer if accessories should be missing or damaged.

Olympus PT-E02 — 1. Preparations diagram (page 7)
Fig. 2 · 1. Preparations

デジタルカメラ 用 防水プロテクタ

Authorized distributors list/ Authorized service centres list

· Instruction manual · (this manual)

Page 8 of the Olympus PT-E02 user manual — Names of the parts
Page 8 · click to enlarge
Page 8

Names of the parts

Palm grip ❈ Shutter lever Hand strap ring ❈ _ (Exposure correction) button ❈ Mode dial knob Accessory mount TTL cable cover Front lid ❈ Zoom dial Front cap ❈ (Information display)button ❈ button ❈ (Erase) button ❈ (Play) button Pickup finder

❈ Eyepiece shutter lever ❈ button ❈ (Live view) button ❈ Control dial knob ❈ button ❈ button ❈ /Cross-cursor button ❈ /Cross-cursor button ❈ button ❈ /Cross-cursor button ❈ (Metering)/Cross- cursor button LCD monitor window Rear lid Camera table O-ring (POL-E01B)

Hot shoe cable mount (with a cap) Loading guide rails Buckle open/close levers Camera table clamping lever Optional bracket mount Buckle hook LCD inner hood O-ring (POL-E01A) Silica gel Grease for silicone O-ring (White cap) O-ring remover Waterproof cap maintenance adapter Hand strap

digital camera. When the operation parts of the Case are operated, the corresponding functions of the digital camera will operate. For details of the functions, refer to the instruction manual for the digital camera.

Page 9 of the Olympus PT-E02 user manual — Names of the parts
Page 9 · click to enlarge
Page 9

Install the Waterproof Port.

To enable the Case to be used underwater, the separately available Waterproof Port for the camera lens must be installed on the Case. Align the Waterproof Port with the position where the camera lens will be when the camera is loaded in the Case. For more details on attaching the Waterproof Port to the Case, refer to the instruction

manual provided with the Waterproof Port Apply the provided O-ring grease to the O-ring section of the Waterproof Port and the

Waterproof Port mounting thread on the Case. Screw the Waterproof Port into the Case by turning it all the way clockwise.

Olympus PT-E02 — Names of the parts diagram (page 9)
Fig. 3 · Names of the parts

Attach the hand strap to the Case.

Olympus PT-E02 — Names of the parts diagram (page 9)
Fig. 4 · Names of the parts
Olympus PT-E02 — Names of the parts diagram (page 9)
Fig. 5 · Names of the parts
Olympus PT-E02 — Names of the parts diagram (page 9)
Fig. 6 · Names of the parts
Olympus PT-E02 — Names of the parts diagram (page 9)
Fig. 7 · Names of the parts

: • Be sure to install the hand strap correctly as shown above.

  • Two hand strap rings are attached to the side of the Case with the palm grip one at the top and one at the bottom. Before using the Case, be sure to attach the ends of the strap to the two hand strap rings.
  • OLYMPUS IMAGING CORP. shall bear no responsibility for damage caused by dropping the Case because of incorrect installation of the hand strap.

Hand strap ring

Page 10 of the Olympus PT-E02 user manual — How to Use the Mode Dial
Page 10 · click to enlarge
Page 10

Mastering basic Case operations.

Before loading the digital camera, be sure you are comfortable with basic Case operations.

How to hold the Case

Hold the Case firmly with both hands so that you can see the image you want to shoot through the pickup finder on the Case or on the LCD monitor.

: • Do not apply excessive force to the waterproof port.

  • Be careful not to block the waterproof port’s lens window.
  • If you want to check the pictures you have just taken on the LCD monitor, the camera must be set to the live view mode. For details, refer to the digital camera’s instruction.

How to Press the Shutter

When pressing the shutter lever, press it gently, so that there will be no movement of the camera.

How to Use the Mode Dial

The case is equipped with a mode dial knob that fits on the camera's mode dial and functions the same way. After inserting the digital camera into the case, make sure that the mode dial knob is operable before taking any image.

: • Make sure that the Case’s mode dial knob is properly positioned on

camera’s mode dial. Remember that the rotation range of the camera’s mode dial is limited. Do not turn the Case’s mode dial knob beyond the rotation range of the camera’s mode dial.

Right Wrong

Page 11 of the Olympus PT-E02 user manual — PPO-E03 +PER-E01
Page 11 · click to enlarge
Page 11

How to use the zoom dial

The Case’s zoom dial can be used to control the digital camera’s zoom ring or its manual focus ring. Which operation is available depends on the lens being used.

Whether or not the Case’s zoom ring can control the camera’s zoom ring and focus ring depends on which lens is mounted on the digital camera. For details, refer to the instruction manual for the optional waterproof port.

Waterproof Port Applicable Lens Zoom Ring Focus Ring Note

14-45mm Controllable Not controllable Only autofocusing is

possible.

PPO-E01

35mm Macro Not controllable Controllable*1 The lens’ focus ring can

be rotated by 360°.

PPO-E02 14-54mm 11-22mm Controllable Not controllable Only autofocusing is

possible.

Manual focusing is possible but the MF ring rotation range is limited to 180°.

PPO-E03 50mm Macro Not controllable Controllable*2

PPO-E03 +PER-E01

50mm Macro +EC14 Not controllable Not controllable Only autofocusing is

possible. PPO-E04 +PER-E02 7-14mm Controllable Not controllable Only autofocusing is

possible.

PPO-E04 8mm Fisheye Not controllable Controllable*3 The lens’ focus ring can

be rotated by 360°.

*1. The optional PPZR-E04 focusing gear is required. *2. The focus ring on the lens can be turned 360° by using the optional PPZR-E04. *3. The optional PPZR-E05 focusing gear is required.

Data as of April 2006.

Page 12 of the Olympus PT-E02 user manual — How to control the eyepiece shutter lever
Page 12 · click to enlarge
Page 12

How to control the power switch lever

Move the power switch lever of the Case to turn the camera ON and OFF.

: When the digital camera has not been operated for a certain period of time, the sleep mode (standby status) is engaged . The duration before the sleep mode is engaged can be set on the digital camera. To exit the sleep mode (and restore camera functions), press any button (such as the shutter button). For details, refer to the digital camera’s instruction manual.

How to control the eyepiece shutter lever

To prevent extraneous light from getting on the viewfinder screen when shooting with the camera and viewfinder held away from your face, use the eyepiece shutter lever on the Case to close the eyepiece shutter.

: Before loading the digital camera in the case, confirm that the camera’s eyepiece shutter is closed. Set the eyepiece shutter lever on the Case to the “Open” position (the position in which the lever is turned fully counterclockwise) before sealing the Case. The camera’s eyepiece shutter lever cannot be controlled if the Case is sealed without aligning the eyepiece shutter lever on the Case with one on the camera.

Power switch lever · Open · Close

Page 13 of the Olympus PT-E02 user manual — Cleaning the TTL connector
Page 13 · click to enlarge
Page 13

Removing the TTL cable connector cap

Olympus PT-E02 — Removing the TTL cable connector cap diagram (page 13)
Fig. 8 · Removing the TTL cable connector cap

To perform TTL flash shooting in combination with the

separately available Electronic Flash Case, remove the TTL cable connector cap as described below.

1Remove the TTL cable connector cap from the Case.

2Connect the Electronic Flash Case’s underwater TTL cable to the TTL connector on the Case.

How to attach the TTL cable connector cap to the case

Make sure there is no foreign matter attached to the O-rings inside the cap and on the TTL cable connector. To secure the cap, gently turn it clockwise until it stops.

Olympus PT-E02 — Removing the TTL cable connector cap diagram (page 13)
Fig. 9 · Removing the TTL cable connector cap

: • If the TTL cable connector cap is loose, water penetration may result. Be

sure to gently turn the cap until it stops to make sure it is firmly secured. Do not turn or tighten the TTL cable too hard. If it is too tight, it may be difficult to loosen and remove it.

❈For details on the TTL cable and hot shoe cable, refer to the instruction manual provided

with the Electronic Flash Case.

Cleaning the TTL connector

If the threaded sections of the TTL cable and TTL cable connector stick to each other, the cable may disconnect from the connector. To prevent this, apply O-ring silicon grease (provided with this case) to the threaded sections. For details, see the maintenance description on page E-32 of this manual.

Contact Olympus for support. CAUTION

: • If you cannot disconnect the TTL cable, do not use force to disconnect it.

Page 14 of the Olympus PT-E02 user manual — How to attach or remove the camera from the camera table
Page 14 · click to enlarge
Page 14

How to connect the hot shoe cable

To perform TTL flash shooting using the Case, connect the hot shoe cable provided with the Electronic Flash Case between the connector on the Case and the digital camera’s hot shoe.

Olympus PT-E02 — How to connect the hot shoe cable diagram (page 14)
Fig. 10 · How to connect the hot shoe cable

Turn the hot shoe cable connector cap inside the case counterclockwise to remove it.

Insert the connector of the hot shoe cable into the case's connector and turn the connector screws all the way clockwise to connect them firmly.

Insert the hot shoe on the hot shoe cable into the hot shoe on the camera.

When not using the hot shoe cable, attach the hot shoe cable cap to the hot shoe cable connector inside the case and turn the cap all the way clockwise to attach it firmly.

of the hot shoe cable into the case’s connector. CAUTION

: • Be sure to remove the camera from the case when inserting the connector

How to attach or remove the camera from the camera table

The digital camera is loaded and clamped in the Case by means of the camera table located inside the front lid of the Case.

Olympus PT-E02 — How to attach or remove the camera from the camera table diagram (page 14)
Fig. 11 · How to attach or remove the camera from the camera t…

Turn the camera table clamping lever counterclockwise to unlock it.

To load the digital camera into the Case, insert the screw of the camera table into the tripod screw hole on the bottom of the digital camera and turn the screw clockwise to secure it. For details, refer to "Attaching the digital camera to the camera table" later in this manual.

Slide the camera table into the camera table base in the front lid of the Case.

Turn the camera table clamping lever all the way clockwise to clamp the camera table.

❈To remove the camera, reverse the above procedure.

Page 15 of the Olympus PT-E02 user manual — Preliminary test
Page 15 · click to enlarge
Page 15

2. Advance Check of the Case

Advance test before use

This Case has been the subject of thorough quality control for the parts during the manufacturing process and thorough function inspections during the assembly. In addition, a water pressure test is performed with a water pressure tester for all products to confirm that the performance conforms to the specifications. However, depending on the carrying and storage conditions, the maintenance status, etc., the waterproof function may be damaged. Before diving, always perform the following advance test and the water leakage test after installation of the camera.

Check the waterproof parts of the Case

Check the waterproof parts of the Case as described below.

1. Ensure that the Case’s O-rings are firmly attached and secured with the buckle. 2. Ensure that the separately available Waterproof Port is installed correctly, and that the Waterproof Port is attached firmly to the O-ring between the Waterproof Port and Case. 3. Ensure that the O-ring of the TTL cable connector is attached firmly and that the cap is screwed into the connector without loosening.

Preliminary test

  • 1. Before loading the digital camera in the Case, immerse the empty Case at depth you intend to use it and make sure there is no water leakage. 2. Main causes of water leakage are as follows.
  • One or more O-rings have not been installed.
  • Part of an O-ring or an entire O-ring is outside the specified groove.
  • O-ring damage, cracks, deterioration or deformation
  • Sand, fibers, hair or other foreign matter sticking to the O-ring, the O-ring groove or the O-ring contact surface.
  • Damage to an O-ring groove or O-ring contact surface.
  • When all of the above causes have been eliminated, check the hand strap and silica gel when closing the Case.

: • The most suitable method for checking water leakage is to immerse the

Case to the intended water depth. When this is difficult, water leakage also can be checked at a shallow depth with no water pressure. Do not feel that this is troublesome, but perform this test. • If the advance test should show water leakage with normal handling, stop using the Case and contact your dealer or an Olympus service station.

Page 16 of the Olympus PT-E02 user manual — Remove the filter from the digital camera
Page 16 · click to enlarge
Page 16

3. Installing the digital camera

Check the digital camera.

Check the digital camera before loading it in the Case.

Battery Confirmation

Underwater shooting can reduce battery life because the picture has to be checked on the LCD monitor before and after shooting. Make sure that you have sufficient remaining battery capacity before use.

should always a fresh fully charged battery before each dive.

Check the remaining number of pictures

Check that the image storage medium has enough room for the number of pictures you want to take.

Remove the hand strap and lens cap from the digital camera

If a strap or lens cap is attached to the digital camera, it must be removed before loading.

: • If the digital camera is loaded without removing the strap or lens cap, it may

get caught between the Case lids and cause water leakage. • When removing the strap and/or lens cap, handle the digital camera carefully. OLYMPUS IMAGING CORP. shall not be responsible for damage caused by improper handling.

Remove the eyecup from the digital camera.

The Case allows you compose your shots in the pickup viewfinder. To improve the view of the pickup viewfinder, remove the camera’s eyecup before loading it in the Case.

: Be sure to remove the eyecup before loading the digital camera. Otherwise, the rear lid of the Case cannot be closed tightly causing water leakage. CAUTION

Remove the filter from the digital camera

If a filter is attached to the lens of the digital camera, remove the filter before loading the digital camera in the Case.

: The digital camera cannot be loaded in the Case while the filter is attached to the lens. Be sure to remove the filter before loading. CAUTION

Page 17 of the Olympus PT-E02 user manual — Checking camera operation
Page 17 · click to enlarge
Page 17

Prepare the digital camera.

Compatible digital camera

This product (PT-E02) is exclusively for use with the E-330 Digital Camera.

Checking camera operation

Refer to the digital camera’s instruction manual for details on how to make sure the camera is operating correctly.

Open the Case.

(1) Unlock the four buckles on the Case. Do this by

Olympus PT-E02 — Checking camera operation diagram (page 17)
Fig. 12 · Checking camera operation

unlocking buckles that are diagonally opposite to each other. Unlock the first pair (either A or B in the illustration on the right), and then unlock the two remaining diagonally opposite buckles.

(2) To open a buckle, hook your finger on the lower

side of the tip of a buckle lever as shown on the right, and lift the buckle up gently.

(3) After unlocking the four

buckles, hold the rear lid of the Case firmly with both hands and open the buckles all the way to separate the rear lid from the front lid.

Page 18 of the Olympus PT-E02 user manual — Attaching the optional zooming/focusing gear(PPZR-E03/04/05) to the lens
Page 18 · click to enlarge
Page 18

Attaching the zoom ring provided with the optional waterproof port on the lens

To control zooming (or to control manual focusing when the mounted lens is a 50 mm macro lens), attach the zoom gear, provided with the optional waterproof port, to the zoom ring on the lens. For details on attaching the zoom gear, refer to the optional waterproof port’s instruction manual.

Olympus PT-E02 — Attaching the optional zooming/focusing gear(PPZR-E03/04/05) to the lens diagram (page 18)
Fig. 13 · Attaching the optional zooming/focusing gear(PPZR-E0…

The lock lever is used to lock the zoom gear.

: • Confirm that the zoom gear is locked firmly with the lock lever.

  • Confirm that the zoom gear is correctly installed on the lens by referring to the Waterproof Port’s instruction manual.

Attaching the optional zooming/focusing gear(PPZR-E03/04/05) to the lens

For details on attaching the zooming/focusing gear, refer to the zooming/focusing gear’s instruction manual.

Page 19 of the Olympus PT-E02 user manual — Attach the digital camera to the camera table
Page 19 · click to enlarge
Page 19

Attach the digital camera to the camera table

Before loading the digital camera in the Case, remove the camera table inside the front lid of the Case and attached it to the digital camera.

(1) Attach the camera table to the tripod

seat on the bottom of the digital camera by means of the tripod screw hole on the digital camera.

(2) The camera table has fixed top-bottom

and front-rear orientations. Refer to the illustration on the right to ensure that you attach it with the correct orientation.

Front Top Bottom · Rear

Page 20 of the Olympus PT-E02 user manual — Attach the digital camera to the camera table
Page 20 · click to enlarge
Page 20

Insert the digital camera in the Case.

Load the digital camera in the Case after checking the following:

  • Is the digital camera turned OFF?
  • Is a medium loaded in the digital camera?
  • Is the battery fully charged?
  • Have the strap, lens cap and filter been removed from the digital camera?
  • Is the camera table provided with the Case attached to the tripod screw hole on the bottom of the digital camera?
  • Has the viewfinder eyecup of the finder of the digital camera been removed?
  • Is the zoom gear attached to the camera lens?
  • Is the camera’s LCD monitor stored on the camera side?
  • Is the camera’ eyepiece shutter open?
Olympus PT-E02 — Attach the digital camera to the camera table diagram (page 20)
Fig. 14 · Attach the digital camera to the camera table

(1) Pull out the zoom dial and mode dial on the Case (pulling out the mode dial also pulls up

the power switch lever) so that they do not get in the way while loading the digital camera.

Set the power switch lever and eyepiece shutter lever as shown below.

(2) Remove the TTL cable connector cap from the hot shoe connector on the top left

corner of the inner side of the front lid of the Case. Connect the hot shoe cable to the connector.

upside down. Be careful not to drop the Case. CAUTION

: • When screwing in the hot shoe connector clamping screw, place the Case

Page 21 of the Olympus PT-E02 user manual — Attach the digital camera to the camera table
Page 21 · click to enlarge
Page 21

(3) Place the camera table with the attached digital

camera on the camera table base in the Case. Do not load the combination by force, but load it gently so that the digital camera does not interfere with parts inside the Case.

After loading the digital camera, connect the hot shoe cable to the camera’s hot shoe.

Once the digital camera is fully inserted, turn the lock lever on the camera table to lock it.

Gently push the Case’s mode dial down and confirm that the zoom dial can smoothly control zooming, the power switch lever can turn the digital camera ON/OFF, and that the mode dial can control the mode dial of the camera.

: • Read the Waterproof Port’s instruction manual carefully to ensure that you

  • correctly attach the zoom gear to the lens’s zoom ring before loading the digital camera. Make sure the zoom ring is positioned correctly during loading.
  • If the zoom gear on the lens is not engaged properly with the gear on Case’s zoom dial, zooming cannot be controlled. Even when the gears are meshed properly, the lens zooming range may be restricted by the way the digital camera has been loaded. Read the Waterproof Port’s instruction manual carefully and set the zoom gear appropriately.
  • When the focusing gear is attached to the lens, also confirm the gear mesh condition.
Page 22 of the Olympus PT-E02 user manual — Insert silica gel
Page 22 · click to enlarge
Page 22

Insert silica gel

Before sealing the Case, insert the accessory silica gel bag (for prevention of fogging) between the bottom right corner of the camera and the Case. Insert the bag with the shorter side facing inside.

Olympus PT-E02 — Insert silica gel diagram (page 22)
Fig. 15 · Insert silica gel

Pay attention to the orientation.

Olympus PT-E02 — Insert silica gel diagram (page 22)
Fig. 16 · Insert silica gel

: • Insert the silica gel bag as far as it will go at the specified location and with

  • the specified orientation. If the orientation is incorrect, the silica gel bag will catch when the Case is sealed and water will leak into the Case.
  • If the bag is only inserted part of the way, it will get caught by the O-ring when you try to seal the Case and water will leak into the Case
  • Once silica gel has been used, its moisture absorption performance will be impaired. Always change the silica gel when you open or close the Case.

Check the loading status.

Always perform the following final checks before sealing the Case.

  • Does the zoom dial operate properly?
  • Is the silica gel inserted all the way at the specified position?
  • Are the O-rings and the O-ring contact surfaces free of dirt and other foreign matter?
  • Are the O-rings installed properly?
  • Is the TTL cable connector cap attached properly without loosening?
  • Can the camera power be switched ON/OFF?
  • Is the mode dial of the camera controllable?
Page 23 of the Olympus PT-E02 user manual — Insert silica gel
Page 23 · click to enlarge
Page 23

Seal the Case.

(1) Gently align the rear lid with the front lid.

(Do this gently so that the O-rings do not slip out of the grooves.)

Olympus PT-E02 — Insert silica gel diagram (page 23)
Fig. 17 · Insert silica gel

(2) Engage the buckles with the hooks (two

Olympus PT-E02 — Insert silica gel diagram (page 23)
Fig. 18 · Insert silica gel

diagonally opposite buckles first, then the other two diagonally opposite buckles)

Hook one pair of diagonally opposite buckles, then hook the other pair.

: Seal the Case by pushing all four buckle lock/unlock levers down in the direction of the arrows. If one of the buckles is left open or unlocked, the Case will not be sealed properly and water leaks will occur.

Page 24 of the Olympus PT-E02 user manual — Visual Inspection
Page 24 · click to enlarge
Page 24

Check the operation of the loaded camera.

After sealing the Case, check that the camera functions normally.

  • Operate the power switch lever on the Case and confirm that the camera is turned ON/OFF.
  • Turn the mode dial knob on the Case and confirm that the camera mode switches properly.
  • Operate the shutter lever on the Case and confirm that the camera shutter is released.
  • Operate the zoom dial on the Case and confirm that the camera’s lens is controlled.
  • Operate other control buttons on the Case and confirm that the camera functions properly as intended.
Olympus PT-E02 — Visual Inspection diagram (page 24)
Fig. 19 · Visual Inspection

: • If the camera does not function properly, remove the camera and reload it,

starting from "Check the digital camera," on page E-16 of this manual. • After loading the camera in the Case, confirm that the Case’s mode dial can be rotated. If not, the Case’s mode dial may not be positioned properly on the camera’s mode dial. Set the mode dials properly.

Visual Inspection

After closing the case tightly, check the seal between the front and rear lids and the connection between the port and case to make sure the O-rings are not twisted, that they sit properly in the grooves, and that no foreign matter has been caught between the two parts.

cause entry of water, so that special attention is required. CAUTION

: • Hairs, fibers, and other narrow items are not very apparent, but they may

Page 25 of the Olympus PT-E02 user manual — Final Test
Page 25 · click to enlarge
Page 25

Final Test

The final test after loading the camera is explained below. This is the only way to eliminate worry about possible entry of water! Always perform this test. It can be performed easily in a water tank or a bathtub. The required time is about five minutes.

Simple water immersion test Explanatory image Hints

As the Case is transparent, waterdrops entering into it can be confirmed easily.

1 Place the Case slowly into the water.

In case of trouble with the O-ring, three seconds are enough for water to enter. Are there air bubbles coming out between the lids? Please check carefully.

2 At first, immerse the Case for only three seconds.

Remove the Case from the water and check that no water has accumulated at the bottom of the Case. Is there any water trickling down?

3 Check that no water has entered into the Case.

Check carefully for air bubbles! Do not perform any operation yet, but just observe.

4 Next, immerse the Case for 30 seconds.

Remove the Case from the water and check that no water has accumulated at the bottom of the Case. Perform very careful confirmation.

5 Check that no water has entered.

Check carefully for air bubbles! Try operation of the buttons used frequently. Check carefully for air bubbles! If there is still no entry of water, everything is OK!

6 Next, check by immersing for three minutes.

This is very important! Has the silica gel become moist? Please check carefully! As the inside can be seen, the inspection for entry of water also can be made securely!

7 This is the final check. Has the silica gel become moist?

If there is no water leakage and everything is functioning correctly, you are ready to start shooting underwater.

Now everything is all right! Have a nice dive! Did you remember to attach the balance weight?

❈The case shown in the above photos is for compact cameras. However, this Case can

also be tested with the same method.

Page 26 of the Olympus PT-E02 user manual — How to use the hand strap
Page 26 · click to enlarge
Page 26

4. Underwater Shooting

How to use the hand strap

Attach the hand strap to the Case, pass your right hand through the hand strap and hold the Case body with the same hand.

Olympus PT-E02 — How to use the hand strap diagram (page 26)
Fig. 20 · How to use the hand strap
Olympus PT-E02 — How to use the hand strap diagram (page 26)
Fig. 21 · How to use the hand strap

Take pictures.

After shooting, confirm picture on the pickup finder or LCD monitor.

Pictures taken while using the Case can be checked on the pickup finder or LCD monitor. Use the camera’s live view function to check pictures on the LCD monitor.

Start shooting while monitoring the LCD monitor display.

Press the (Live view) button of the Case to display the picture you have just taken on the LCD monitor. At this time, the button of the Case can be used for various operations including picture composition and focusing.

Olympus PT-E02 — How to use the hand strap diagram (page 26)
Fig. 22 · How to use the hand strap

Mode A The subject is displayed on the LCD monitor so you can compose your shot.

Mode B The button can be used to display the subject by magnifying it by 10 times. The magnified picture can facilitate confirmation and adjustment of focusing.

: • When using mode A, close the eyepiece shutter to ensure accurate

  • photometry.
  • Autofocusing is not available in mode B.
  • For details on the live view function, refer to the camera’s instruction manual.
  • For detailed operations of modes A and B, refer to the camera’s instruction manual.
Page 27 of the Olympus PT-E02 user manual — 5. Handling After Shooting
Page 27 · click to enlarge
Page 27

Gently press the shutter lever.

When pressing the shutter lever, hold the Case securely with both hands and operate the lever gently to prevent camera shake.

Cautions when using the flash

The E-330’s built-in flash cannot be used when the camera is loaded in the Case. When flash shooting is required, use the separately available Electronic Flash and Electronic Flash Case.

: When using the separately available Electronic Flash and Electronic Flash Case, a bracket is also required to combine the Electronic Flash Case with this Case.

5. Handling After Shooting

Wipe off any waterdrop.

After underwater shooting, remove any drops of water from the case. Use pressurized air or a soft, lint-free cloth to carefully wipe away any moisture from the hinge between the front and rear lids, the shutter release lever, the handgrip and the buckles.

: • Water left between the front and rear lids or between the case and port can

  • get inside the case once it is opened or the port is detached. Please dry these areas carefully.
  • When opening the case or removing the port, make sure no water from outside (e.g. drops from your hair or the diving suit) gets inside of the case and/or on the camera!
  • Before opening the case or removing the port, ensure that your hands or gloves are completely clean (free of sand, loose fibers, etc.).
  • Never open the case or remove the port in areas where water could splash or spray or where sand or dust could be blown in the air. When this cannot be avoided, for example if the battery or memory card needs to be changed, the case and camera should be protected from the wind or spray with a plastic sheet or similar object.)
  • Never touch the digital camera and/or battery you're your hands are wet with sea water.
Page 28 of the Olympus PT-E02 user manual — B
Page 28 · click to enlarge
Page 28

Remove the digital camera.

Unlock the buckles on the Case as shown below and carefully open the rear lid. Then, pull out the zoom dial and mode dial, turn the camera table lock lever counterclockwise, and gently lift the camera out of the case using both hands. To remove the digital camera from the Case, simply reverse the procedure described in “Insert the digital camera in the Case” on page E-20 of this manual.

Olympus PT-E02 — Cautions when using the flash diagram (page 28)
Fig. 23 · Cautions when using the flash

B

Unlock two buckles on opposite corners first, and then unlock the other two buckles.

B

Olympus PT-E02 — B diagram (page 28)
Fig. 24

Pull out the zoom dial and mode dial on the Case so that they do not get in the way when you are removing the camera. After pulling out the dials, gently remove the camera using both hands.

: • After opening the Case, always place it so that the O-ring surface is face

  • up. If the O-ring surface is face down, foreign matter and dirt may attach to the O-ring and O-ring contact surface. This may cause the Case to leak the next time it is used underwater.
  • For the picture storage and other procedures, refer to the camera’s instruction manual.
  • Be sure to pull out the zoom dial and mode dial of the Case before taking the digital camera out so that the dials do not get in the way. Otherwise, if the digital camera is removed forcefully, the Case or digital camera may be damaged.
Page 29 of the Olympus PT-E02 user manual — Cautions when using the flash
Page 29 · click to enlarge
Page 29

Wash the Case with pure water.

After use, seal the Case again after taking out the camera and wash it sufficiently in pure water as soon as possible. After use in sea water, it is effective to immerse it for a fixed time in pure water to remove any salt.

: • Water leakage may be caused when a high water pressure is applied

  • locally. Before washing the Case with water, remove the digital camera from it.
  • Operate the shutter lever and various buttons of this product in pure water to remove salt adhering to the shaft. Do not disassemble for cleaning.
  • Drying the Case with adhering salt may impair the function. Always wash off any salt after use.

Dry the Case.

After washing with pure water, use a soft cloth without any salt on it and not causing any fibers to wipe off any waterdrop and dry the Case completely at a well ventilated location in the shade.

: • Do not use hot air from a hair drier or the like for drying and do not expose the

Case to direct sunlight, as this may accelerate deterioration and deformation of the Case and deterioration of the O-ring, leading to leakage of water. When wiping the Case, take care not to cause scratches.

Page 30 of the Olympus PT-E02 user manual — 6. Maintaining the Waterproof Function
Page 30 · click to enlarge
Page 30

6. Maintaining the Waterproof Function

Remove the O-ring.

Open the Case and remove the O-ring. Procedure Insert the O-ring remover into the gap between the O-ring and O-ring groove wall. Bring the tip of the inserted O-ring remover below the O-ring. (Be careful not to damage

the groove with the tip of the O-ring remover.) Lift the O-ring, pinch its with your fingertips and pull it out of the Case.

Olympus PT-E02 — 6. Maintaining the Waterproof Function diagram (page 30)
Fig. 25 · 6. Maintaining the Waterproof Function

Remove any sand, dirt, etc.

After visually checking that dirt has been removed from the O-ring, checking for attached sand and other foreign matter, as well as for damage and cracks can be done by squeezing the entire circumference of the O-ring lightly with your fingertips.

Remove attached foreign matter from the O-ring groove with a clean cloth or a cotton swab. Also remove any sand or dirt attached to the any part of the Case that comes into contact with the O-ring.

: • When a mechanical pencil or a similar other sharp object is used to remove

  • the O-ring or to clean the inside of the O-ring groove, the Case and the Oring may be damaged and water leakage may be caused.
  • When the O-ring is checked with the fingertips, take care not to stretch the O-ring.
  • Never use alcohol, thinner, benzene or similar solvents or chemicals detergents to clean the O-ring. When such chemicals are used, it is likely that the O-ring will be damaged or that its deterioration will be accelerated.
Page 31 of the Olympus PT-E02 user manual — How to Apply Grease to the O-ring
Page 31 · click to enlarge
Page 31

Install the O-ring.

Confirm that no foreign matter is attached, apply a thin coat of the accessory grease to the O-ring, and fit the O-ring into the groove. At this time, confirm that the O-ring does not stick out from the groove.

How to Apply Grease to the O-ring

Make sure that your fingers and the O- ring are free of dirt, and squeeze about 5 mm of lubricant onto a finger. (5 mm is the most appropriate amount.)

1 Apply the exclusive lubricant to each O- ring.

Surround the lubricant with three fingers and spread it over the ring. Be careful not to use excessive force as this may stretch the O-ring.

2 Spread the lubricant all over the O-ring.

Check that the O-ring is free of scratch or unevenness.

After spreading the lubricant, check visually and by touch that the O-ring is not scratched and that its surface is flat. If it is damaged in any way, replace it with a brand-new O-ring.

4 Apply lubricant on the O-ring contact surface.

Use the lubricant remaining on the fingers to clean and lubricate the case's contact surface.

: • Always perform maintenance of the waterproof function even when the

  • Case has been opened to exchange the battery or the image storage during shooting. Neglecting this maintenance may become the cause of water leakage.
  • When the Case is not to be used for a long time, remove the O-ring from the groove to prevent deformation of the O-ring, apply a thin coat of silicone grease, and store it in a clean plastic bag or the like.
  • When drying is done with salt attached, it is likely that a function impairment will be caused. After use, always wash off any salt.

Replace consumable products.

  • The O-ring is a consumable product. Independent of the number of times the Case is used, it is recommended that the O-ring should be replaced by a new one at least once a year.
  • Deterioration of the O-ring is accelerated by the use conditions and the storage conditions. Replace the O-ring even before a year has passed if it shows signs of damage, cracking or loss of elasticity.

gel, and the O-ring. These consumable products also can be purchased at an Olympus service station.

Page 32 of the Olympus PT-E02 user manual — Maintenance of the TTL Connector Cap
Page 32 · click to enlarge
Page 32

Maintenance of the threaded sections on the TTL cable and TTL cable connector

If the threaded sections used to connect the TTL cable to the TTL cable connector are not maintained properly, salt and other seawater residue may adhere the TTL cable and prevent it from being disconnected. After use in seawater, clean off any salt, sand, or other residue as soon as possible, then dry the equipment thoroughly. Clean the threaded sections with a cotton swab and apply a thin, uniform layer of O-ring silicon grease (provided with this case).

Clean and apply O-ring silicon grease to these sections.

Maintenance of the TTL Connector Cap

After removing the TTL connector cap from the waterproof cap, be sure to clean and grease the O-ring. Use the waterproof cap maintenance adapter to remove the O-ring unit from the waterproof cap.

Waterproof cap Waterproof cap maintenance adapter

Insert the adapter by aligning its pin with the hole on the cap.

Turn the adapter counterclockwise to remove the O-ring unit.

After removing the O-ring attached to the O-ring unit, clean the O-ring groove and apply silicon grease to the O-ring. Then, re-attach the O-ring to the O-ring unit.

❈Reverse the removal procedure to re-attach the O-ring unit to the waterproof cap.

O-ring

Page 33 of the Olympus PT-E02 user manual — 7. Appendix
Page 33 · click to enlarge
Page 33

7. Appendix

Q&A on the use of the PT-E02

Q1: What digital cameras can be used? A1: The PT-E02 is only for use with the E-330 digital camera.

Q2: Is underwater shooting possible with the PT-E02 alone? A2: In addition to the Case, you need the separately available Waterproof Port matching

the lens you are using.

Q3: What precautions must be observed when loading the digital camera into the Case? A3: Pay special attention to the following items when loading the camera into the Case.

(1) Check that the camera’s remaining battery capacity is sufficient. (2) Check how many pictures can be stored on the image storage medium.

Please use a medium with enough space to store all the pictures you want to take. This minimizes the number of times the Case has to be opened and closed. (3) Check that the zooming and focusing gears are attached properly to the lens of the

digital camera. (4) When using an external flash, check that the hot shoe cable is connected to the digital

camera. (5) Remove the carrying strap and lens cap from the digital camera.

If the carrying strap and lens cap are not removed from the digital camera, they could catch between the two lids of the case and prevent it from closing properly. This could lead to water penetration. (6) Before closing the case, check that the O-rings sit correctly in the groove. (7) Make sure that the buckles used for connection of the case and port and TTL

connector cap are closed firmly. (8) Make sure that the O-rings and the case's contact surfaces are free of foreign matter

and dirt. (9) Place the silica gel bag in the case to avoid fogging. Only use Olympus silica gel.

Q4: What cautions must be observed when using and storing the Case? A4: Pay special attention to the following items.

(1) When the O-ring contact surface is pressed strongly from the outside of the Case, or

when the Case is twisted, the waterproof function may be impaired and water leakage may be caused. (2) When the Case is used, left or stored at the following locations, defective operation or

trouble may be caused. Always avoid such locations. (a) Places where the Case can reach high temperatures under direct sunlight or in a

car, places with extremely low temperatures, and places with extreme temperature variations (b) Places with open fire (c) Places with volatile substances (d) Places with vibrations (3) In case of the following handling with a camera loaded into the Case, trouble or

breakage may be caused for the Case and/or the loaded camera. Always avoid such handling. (a) Hitting other objects (b) Dropping

Page 34 of the Olympus PT-E02 user manual — 7. Appendix
Page 34 · click to enlarge
Page 34

(c) Placing heavy objects on top of the Case (4) When the Case is not used for a long time, trouble from formation of mold etc. may be

caused. Before use, confirm the operation of all operation parts and perform the advance test and the final test.

Q5: What cautions must be observed when opening and closing the Case? A5: Pay special attention to the following items.

(1) Do not open and close the Case at locations with water spray or sand spray. (2) Wipe off all waterdrops from the gap between the front lid and the rear lid and around

projections and recesses such as the buckles. When this is not done, entry of waterdrops into the Case is to be feared at the time of opening and closing. (3) When opening the Case, take care that no water will drip from your hair or body into

the Case or onto the camera. (4) When the case is open, examine the O-rings and the O-ring contact surfaces on the

front lid for foreign matter such as hair, fiber, and grains of sand. Remove these if present. Also examine the O-rings used for connection of the case and port. (5) Do not touch the camera or the image storage with your hands to which sea water is

sticking. (6) If you should detect waterdrops or other signs of water leakage while shooting,

immediately end the dive, perform the water leakage test again, and confirm that there is no leakage. If the camera is wet, wipe off any moisture and check the operation.

Q6: How should the Case be handled after use? A6: After use, take out the camera as soon as possible and wash the Case with pure

water. In case of use in the ocean, it is effective to immerse the Case for a certain time in pure water to remove any salt. Operate the buttons and levers under water to turn the shafts and wash off any salt. After washing, use a dry cloth without any salt on it to wipe off any moisture and dry the Case in the shade. Do not use hot air from a hair drier or the like and do not dry the Case under direct sunlight. Exposure to high temperatures or direct sunlight may cause deformation, discoloration or breakage of the Case and deterioration of the O-ring. Wipe the inside of the Case with a soft cloth not causing any fibers. Remove the O-ring, wipe off any salt, sand, dust, etc., and also clean the O-ring groove and the O-ring contact surface in the same way and then dry them. When an object with a sharp tip is used to remove the O-ring from the groove, the O-ring may be damaged and water leakage may be caused. Always use the accessory pick for O-ring removal.

Q7: How can I check for water leakage? A7: For confirmation, perform the advance test and the final test after loading the camera.

The advance test with immersing the Case without the camera to the intended use depth to check for water leakage is the most accurate test, but when this is difficult, it is safer to perform this test even at a depth of 1 m or in a bathtub. The final test also can be performed in a bathtub or a bucket.

Q8: What are the causes for entry of water? A8: The main causes for the entry of water are shown below. Please check them most

carefully. (1) Forgetting to install the O-ring (2) The O-ring is partly or completely outside the groove. (3) Damage, deterioration, or deformation of the O-ring

Page 35 of the Olympus PT-E02 user manual — 7. Appendix
Page 35 · click to enlarge
Page 35

(4) Sand, fibers, hair or other foreign matter on the O-ring (5) When foreign matter (sand, fiber, hair, etc.) is stuck to the O-ring grooves or O-ring

contact surfaces. (6) Catching of the strap, the bag of silica gel, etc. at the time of sealing the Case. (7) Throwing the Case from a boat into the water, jumping with the Case into the water, or

other sudden application of strong forces onto the Case. When entering the water, hand the Case over quietly or avoid impacts in other ways.

Q9: What are the important points for O-ring maintenance? A9: Please observe the following items.

(1) Never use alcohol, thinner, benzene or similar organic solvents or chemical detergents

to clean the O-ring. When such chemicals are used, it is to be feared that the O-ring will be damaged or that its deterioration will be accelerated. (2) Always use genuine Olympus Grease for Silicone O-Ring (white cap). Other grease

may not be suitable for the silicone O-rings on the Case. Using the wrong grease may result in deterioration of the Case’s surface finish and interfere with the waterproof capability. (3) In order to avoid deformation of the O-ring when the Case is not used for a long time,

remove the O-ring from the Case, apply a thin coat of the special grease, and store the O-ring in a clean plastic bag. For reuse, confirm that the O-ring is free of damage and cracks, that it has sufficient elasticity, that the surface is free of stickiness and other abnormalities, and use it after applying a thin coat of the special grease. Excessive application of grease does not improve the waterproof function or the permissible withstand pressure. However, it may facilitate attachment of sand, dirt, etc. A thin, uniform coat produces the best result. (4) When using an external flash, check that the hot shoe cable is connected to the digital

camera. (5) The O-ring is a consumable product. Replace it at least once a year. (6) Deterioration of the O-ring is accelerated by the use conditions and the storage

conditions. Replace the O-ring immediately by a new one if it shows signs of damage, cracking or loss of elasticity.

Q10: What are the important points for Case maintenance? A10: Please observe the following items.

(1) Never use the following chemicals for cleaning, corrosion protection, defogging, repair

  • or other purposes.
  • Never use alcohol, thinner, benzene or similar volatile organic solvents or chemical detergents to clean the Case. Pure water or lukewarm water is sufficient for cleaning.
  • Do not use anticorrosion agents on the metal parts. The metal parts are made of aluminum, brass or stainless steel. Cleaning with pure water is sufficient.
  • Do not use commercial defogging agents. Always use the original Olympus defogging silica gel.
  • Do not use adhesive for repairs or other purposes. When repair is required, please contact a service station of our company or your dealer.

Q11: Please tell me about repairs. A11: Please contact a service station of our company or your dealer, if repair should be

necessary. Do not try to repair, disassemble or modify the Case yourself. Repair, disassembly or modification by you or third parties not authorized by Olympus invalidates the guarantee.

Page 36 of the Olympus PT-E02 user manual — PER-E01 EC-14
Page 36 · click to enlarge
Page 36

Q12: What are the model numbers of the accessories for the PT-E02? A12: The following accessories are available:

(1) O-rings for the PT-E02 body (POL-E01A, POL-E01B): These are silicone rubber O-

rings that have to be installed in the PT-E02 body to make it waterproof. There are two types of O-rings. O-rings for other Case models cannot be used. (2) The following waterproof ports are available for use with the PT-E02 Choose the one

corresponding to the lens you are using.

Waterproof Port Applicable Lens Note

14-45mm Provided with an exclusive zooming gear.

PPO-E01

35mm Macro The lens’s focus ring can be rotated 360° using the optional PPZR-E04.

PPO-E02 14-54mm 11-22mm Provided with an exclusive zooming gear.

PPO-E03 50mm Macro* Provided with an exclusive zooming gear. The MF ring rotation range is limited to 180°.

When using the EC-14 lens, attach between the waterproof port and Case.❈The MF ring rotation range is limited to 180°.

PER-E01 EC-14

PPO-E04 +PER-E02 7-14mm Only autofocusing is possible.

PPO-E04 8mm Fisheye The lens’ focus ring can be rotated by 360° using the optional PPZR-E05.

* The focusing ring of the lens can be rotated by 360° using the optional PPZR-E04.

(3) Grease for silicon O-ring (PSOLG-1): Exclusive grease for maintenance of the silicon

O-ring. (4) Silica gel (SILCA-5)Desiccant agent to reduce fogging of the glass parts of the case

due to condensation. ❈You can order in large computer shops and camera mass sale stores. ❈Please contact your dealer or a service station of our company when replacement is

required. Replacement will be made against payment.

Page 37 of the Olympus PT-E02 user manual — Specifications
Page 37 · click to enlarge
Page 37

Specifications

Available models Olympus Digital Camera E-330

Pressure resistance Depth of up to 60 m

Main materials Main body: Transparent polycarbonate resin. Release lever/power switch dial/mode dial/control dial/zoom dial/camera table: Polycarbonate resin. Port mount/camera table mount/pickup viewfinder frame/optional bracket mount/zoom dial gear/TTL connector cap: Aluminum. Operation buttons/buckles/accessory mount cover: Nickel-plated brass. Body cap: ABS resin. O-rings: Silicone rubber. Inner LCD hood: NBR rubber.

Dimensions Width 214 mm x height 168 mm x thickness 154 mm

Weight 1860 g (LCD hood not included)

❈We reserve the right to change the external appearance and the specifications without

Page 38 of the Olympus PT-E02 user manual — MEMO
Page 38 · click to enlarge
Page 38

MEMO

Page 39 of the Olympus PT-E02 user manual — MEMO
Page 39 · click to enlarge
Page 39
Olympus PT-E02 — MEMO diagram (page 39)
Fig. 26
Olympus PT-E02 — MEMO diagram (page 39)
Fig. 27
Olympus PT-E02 — MEMO diagram (page 39)
Fig. 28
Page 40 of the Olympus PT-E02 user manual — Mode d’emploi
Page 40 · click to enlarge
Page 40

Mode d’emploi

Caisson étanche

Pour l’appareil photo numérique E-330 PT-E02

Fr

Ask about the Olympus PT-E02

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Olympus PT-E02

Be the first to ask — other owners or our team will answer.

Original document

Olympus PT-E02 manual PDF

284 pages·17.3 MB·Camera Accessories·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…