
tion manual carefully. After reading, store the manual together with the warranty card in a safe, easily accessible place. ■ This product is the Waterproof Lens Port (PPO-E02) designed exclusively for use with the PT-E series of
waterproof case. ■ Underwater zooming is made possible by attaching the zoom gear, provided with this product, to the zoom
ring of an applicable camera lens.
reproduction is strictly prohibited. ■ Olympus shall not be responsible for damages, loss of profit or any claims by third parties in case of any
damage occurring from incorrect use of this product.
product with care. ■ This product must always be used in combination with an applicable lens. Do not combine this product
with an inapplicable lens. ■ To ensure correct and safe use of this product, always use it as described in this instruction manual.
This instruction manual uses pictographs to show how to use the product correctly and how to prevent danger to the user and other persons as well as damage to property. These pictographs and their meanings are shown below.


PPO-E02 main body Silicon O-ring (POL-E101) Front cap Rear cap Zoom gear Grease for silicone O-ring Pick for O-ring removal
This section describes how to mount this product on the PT-E series case. Before mounting, check that no for- eign matter is attached to the O-rings, the port mount thread on the PT-E series case, or the O-ring contact sur- faces. Apply a thin layer of the provid- ed silicone O-ring grease.
Align the threaded section of the PPO-E02 with the port mount thread on the PT-E series case. Hold the PT-E series case firmly with one hand, hold the main body of the PPO-E02 with your other
hand and screw it into the PT-E series by turning the PPO-E02 clockwise. Resistance increases as the PPO-E02 is screwed in more deeply. However, be sure to screw it in all the
way until there is no gap visible below the threaded section of the PPO-E02.



If any water is on the product, wipe it completely away and
Holding the PT-E series case firmly with one hand, loosen the
PPO-E02 by turning it about 90 degrees counterclockwise. If the PPO-E02 is attached too tightly to turn, wrap it with a piece of rubber or similar non-slip material.
After loosening the PPO-E02, point its lens downward and
turn it further counterclockwise until it is separated from the PT-E series case. Be careful not to drop the PPO-E02 or PT-E series case.
ter on the lens or camera. If this happens, wipe the water off the lens and camera with a dry cloth. ・Make sure that the port is completely dry before dismounting.

To control zooming of the camera lens, the provided zoom gear must be attached to the zoom ring of the lens.
Turn the zoom ring of the lens so that the correct number
(see the following table) is aligned with the zoom index.
Corresponding lens Number to align with the zoom index ZUIKO DIGITAL 14-54mm F2.8-3.5 25 ZUIKO DIGITAL 11-22mm F2.8-3.5 14
Check the position of the lock dial’s hinge on the zoom gear,
then turn the lock dial counterclockwise to release the lock and open the gear.
Open the zoom gear wide and align its hinge with the zoom
index on the lens. Place the zoom gear on the lens and adjust the rotation direction of the zoom gear. At this time, bring the gear section of the zoom gear to the left of the hinge as shown in the illustration.
Align the hinge with the index.
Set the front-rear direction of the zoom gear by aligning the
edge of the hinge with the end of the rubber section on the lens’ zoom ring.
After positioning the zoom gear, place it against the lens’s
zoom ring (taking care not to displace the zoom gear), and turn the zoom gear’s lock dial all the way clockwise to lock it. Push the gear with a finger to place the gear against the lens.
Turn the lock dial to lock the zoom gear.
zooming cannot be controlled properly. Be sure to attach the zoom gear correctly.

After attaching the zoom gear to the camera lens, insert the camera and lens into the PT-E series case on which the PPO-E02 is mounted.
Screw the camera table provided with the PT-E
Remove the eyecup from the camera’s viewfind-
series case firmly into the bottom of the cam- era.
er. If a lens cap or filter is attached to the lens or the strap is attached to the camera, remove them as well.
Pull out the zoom dial further.
Camera table lock lever
Lift the PT- E series case’s power switch dial,
Confirm that the camera’s power switch is OFF.
mode dial knob and zoom dial, and turn the case’s camera table lock lever counterclock- wise to release the lock. Refer to the PT-E series case’s instruction manual for instructions of how to attach the hot shoe cable for the flash.
Align the correct zoom value for the lens with the zoom index of the lens. While pulling out the zoom dial on the PT-E series case, slide the camera table with camera attached as far as it will go into the camera table mount on the inner side of the case’s front lid.

After inserting the camera, turn the PT- E series
Push in the PT- E series case’s power switch
case’s camera table lock lever all the way clock- wise to lock the camera table. Then, push in the zoom dial on the case and engage it with the zoom gear attached to the lens. Turn the zoom dial to confirm that it can control zooming.
dial and mode dial knob. Turn the power switch dial and mode dial knob and confirm that they can control the camera power ON-OFF and mode switching. Connect the hot shoe mount section of the hot shoe cable that has been connected to the PT-E series case to the hot shoe of the camera.
Attach the rear lid of the PT- E series case and
lock the four buckles (two diagonally located buckles first, and then the other two diagonally located buckles). Underwater shooting is now possible.

For safe use of this product, always perform maintenance after each diving session. For details, refer to “Handling After Shooting” and “Maintaining the Waterproof Function” in the PT-E series case instruction manual. Apply the same procedures to this product.


era and lens, then re-seal the empty case and immerse it in tap water to remove any salt as soon as possible.
case is completely dry, dismount this product from the case.
Remove sand and dust from the O-rings.
using the provided pick for removing O-rings. Take care not to damage the O-rings.
Pinch each O-ring between your fingers and lightly rub the entire circumference to check for foreign matter, scratches and cracks.


If any foreign matter is attached to the
After removing foreign matter, apply the
O-ring grooves, remove it using a clean, lint-free cloth or cotton swab. Also remove any foreign matter from the O-ring contact surfaces and from the port mount thread on the PT-E series case.
provided grease to the O-rings and fit them into the O-ring grooves. To apply grease to each O-ring, squeeze a drop of grease about the size of a grain onto your finger and lightly rub the entire circumference of the O-ring to spread the grease thinly and evenly.

Applicable case : PT- E series Applicable lens : ZUIKO DIGITAL 14-54mm F2.8-3.5/ZUIKO DIGITAL 11-22mm F2.8-3.5 Main materials Main body : Aluminum. Lens window : Chemically reinforced glass. O-rings : Silicon rubber. Zoom gear : Polycarbonate resin. Front cap : NBR rubber. Rear cap : Polyethylene resin. Withstanding pressure : Water depth of 60 m (200 ft) Dimensions : Max. diameter 143 mm x Depth 105 mm Weight : 650 g (excluding the conversion lens)
This product uses the following consumable items.

Description O-ring for use with the PT-E series case.
Shinjuku Monolith, 3-1 Nishi Shinjuku 2-chome, Shinjuku-ku, Tokyo, Japan
Tel: +49 40-23 77 3-0 Fax: +49 40-23 07 61 Goods delivery : Bredowstrasse 20, 22113 Hamburg, Germany Letters : Postfach 10 49 08, 20034 Hamburg, Germany
European Technical Customer Support: Please visit our homepage http://www.olympus-europa.com or call our TOLL FREE NUMBER* : 00800 - 67 10 83 00
Two Corporate Center Drive, Po Box 9058, Melville, NY 11747-9058, U.S.A. Tel. 631-844-5000
Technical Support (USA) 24/7 online automated help: http://www.olympusamerica.com/support Phone customer support: Tel. 1-888-553-4448 (Toll-free)
for Austria, Belgium, Denmark, Finland, France, Germany, Italy, Luxemburg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom *Please note that some (mobile) phone services/ provider do not permit access or request an additional prefix to +800 numbers.
Our phone customer support is available from 8 am to 10 pm (Monday to Friday) ET E-Mail: distec@olympus.com Olympus software updates can be obtained at: http://www.olympus.com/digital/
For all not listed European Countries and in case that you can’t get connected to the above mentioned number please make use of the following CHARGED NUMBERS: +49 180 5 - 67 10 83 or +49 40 - 237 73 899 Our Technical Customer Support is available from 9am to 6pm MET (Monday to Friday)
© 2005 OLYMPUS IMAGING CORP.
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.