Instruction/ maintenance manual of the product MAUSB-10 Olympus
Go to page of 52
USB Reader/Writer REFERENCE MANU AL.
2 Introduction Thank you for purchasing our product. This product is exclusively for reading and writing data to an xD-Picture Card/SmartMedia. Y ou can transfer large amounts of data to and from the card quickly and easily using a computer equipped with a USB port (IBM PC/A T compatibles and Macintosh).
3 Contents Introduction .................................................................................................................................... 2 Contents ...................................................................................
4 What’ s inc luded Make sure all the following items are included. If any items are missing, inform the shop from where you purchased this product right away .
5 Before getting started System requirements Y our computer must conform to the following minimum standards in order to use it with the MAUSB-10. ● Compatible operating systems IBM PC/A T compatible.
6 W indows Macintosh [USB 1.1 compatible] T urn on computer . Place provided Installation CD-ROM in CD-ROM drive. *2 Install driver . *2 Restar t computer . *2 Connect to computer . Get started! *4 *1 : Windows 95/3.1/NT are not compatible. *2 : Y ou only need to perform this procedure before using the MAUSB-10 for the first time.
7 How to install Also refer to your computer ’s user manual and the manuals for any optional devices you are using. 1 T ur n on the computer <98/98 SE/Me ⽧ Install> T urn on your computer’s power (and connected devices) to start Windows.
8 <98/98 SE/Me ⽧ Install> 4. During installation, the window at right appears. * The installation time may vary , depending on your computer. 5. When the driver installation is complete, the window at right appears. Click the “Finish” button.
9 1. Double-click “My Computer”. <98/98 SE/Me ⽧ Install> 2. Right-c lic k “OL YMPUS”. Select “Open” from the pop-up menu. 4. Double-click “SETUP”. * The “OL YMPUS USB Reader/Writer InstallShield Wizard” window appears. Start installing by following “Install the device driver” ( 墌 p.
10 Operating the MAUSB-10 The operating procedures for the MAUSB-10 under Windows are described below . 1 Connecting to the computer <98/98 SE/Me ⽧ Operation> After installing the device driver , connect the MAUSB-10’ s connector to the USB port on your computer .
11 < 98/98 SE/Me ⽧ Operation > When the MAUSB-10 is connected to your computer , it is recognized as a “Removable Disk”. Y ou can see two “Removable Disk” icons by opening “My Computer” from the desktop.
12 2 Inserting a card <98/98 SE/Me ⽧ Operation> 1. Make sure the MAUSB-10 is connected to the computer and insert the card into the corresponding card slot. [xD-Picture Card] Make sure the card is level and that the gold-colored contact area is facing down .
13 3 Removing a card <98/98 SE/Me ⽧ Operation> Close all software programs that are using data on the card (e.g. Explorer , graphics applications), then follow the steps below . Attention! If you do not follow the steps below , the data on the card(s) may be damaged.
14 4 Copying files from a card <98/98 SE/Me ⽧ Operation> 4. Drag the file icons you want to copy and drop them onto the destination folder . * The process is the same as copying files from a floppy disk. * It is also possible to move files to another folder, erase files, or write data from another folder .
15 5 Formatting a card <98/98 SE/Me ⽧ Operation> 6 Disconnecting the MAUSB-10 <98/98 SE/Me ⽧ Operation> Close all software programs that are using the card (e. g. Explorer , graphics applications), then follow the steps below . 1. Make sure that the status lamp is NOT on.
16 How to uninstall the device driver <98/98 SE/Me> The device driver can be deleted if it is no longer needed. First make sure that the MAUSB-10 is disconnected from the computer’ s USB port, then follow the steps below . * On-screen displays or messages may vary depending on the version of Windows you are using.
17 How to uninstall the device driver (Cont.) <98/98 SE/Me> 4. A confirmation window appears. Click “OK”. 5. The “InstallShield Wizard” window appears. 6. The window at right appears. Click the “Finish” button. 7. The window at right appears.
18 How to install Also refer to your computer ’s user manual and the manuals for any optional devices you are using. 1 T ur n on the computer <2000/XP ⽧ Install> T urn on your computer’s power (and connected devices) to start Windows 2000/XP .
19 <2000/XP ⽧ Install> 4. During installation, the window at right appears. * The installation time may vary , depending on your computer. 5. When installation of the device driver is complete, the window at right appears. Click the “Finish” button.
20 1. Double-click “My Computer”. <2000/XP ⽧ Install> 2. Right-c lic k “OL YMPUS”. Select “Open” from the pop-up menu. 4. Double-click “SETUP”. * The “OL YMPUS USB Reader/Writer InstallShield Wizard” window appears. Start installing by following “Install the device driver” ( 墌 p.
21 Operating the MAUSB-10 The operating procedures for the MAUSB-10 under Windows 2000/XP are described below . 1 Connecting to the computer <2000/XP ⽧ Operation> After installing the device driver , connect the MAUSB-10’ s connector to the USB port on your computer .
22 <2000/XP ⽧ Operation> [Installing the hardware] 1. The “Found New Hardware Wizard” window appears when the MAUSB-10 is connected to Windows XP for the first time. Make sure that “Install the software automatically [Recommended]” is selected and click the “Next” button.
23 <2000/XP ⽧ Operation> 5. When the driver installation is complete, the window at right appears. Click the “Finish” button. 6. Confirm that two “Removable Disk” icons have been added by opening “My Computer” from the desktop. * The drive letters (e.
24 Before connecting After connecting MAUSB-10 * In this example, the Removable Disks are recognized as the J and K drive. The drive letters (e.g. “J:”, “K:”, etc.) used by your computer may dif fer depending on your computer and/or connected optional devices.
25 2 Inserting a card <2000/XP ⽧ Operation> 1. Make sure the MAUSB-10 is connected to the computer and insert the card into the corresponding card slot. [xD-Picture Card] Make sure the card is level and that the gold-colored contact area is facing down .
26 3 Removing a card <2000/XP ⽧ Operation> Close all software programs that are using data on the card (e.g. Explorer , graphics applications), then follow the steps below . Attention! If you do not follow the steps below , the data on the card(s) may be damaged.
27 4 Copying files from a card <2000/XP ⽧ Operation> 1. Start up your computer . 2. Double-click “My Computer” from the desktop. 3. T o view the contents of a card, double-clic k the corresponding “Removable Disk” icon.
28 5 Formatting a card <2000/XP ⽧ Operation> [Before formatting the card] • T o format a card, log on with the user name “Administrator”, or use a user name with administrator privileges. Otherwise, formatting the card will be impossible.
29 6 Disconnecting the MAUSB-10 <2000/XP ⽧ Operation> Close all software programs that are using data on the card (e.g. Explorer , graphics applications), then follow the steps below . 1. Make sure that the status lamp is NOT on. 2. Left-click the “Unplug or Eject Hardware” icon on the taskbar .
30 How to uninstall the device driver <2000/XP> The device driver can be deleted if it is no longer needed. First make sure that the MAUSB-10 is disconnected from the computer’ s USB port, then follow the steps below . * On-screen displays or messages may vary depending on the version of Windows you are using.
31 How to uninstall the device driver (Cont.) <2000/XP> 4. A confirmation window appears. Click “OK”. 5. The “InstallShield Wizard” window appears. The device driver is no longer installed. 6. The window at right appears. Click the “Finish” button.
32 How to install Also refer to your computer ’s user manual and the manuals for any optional devices you are using. 1 T ur n on the computer <Mac OS 8.6~9.2 ⽧ Install> T urn on your computer’s power (and connected devices) to start Mac OS.
33 3 Install the device driver <Mac OS 8.6~9.2 ⽧ Install> When using the MAUSB-10 for the first time, you must first install the device driver included on the provided CD-ROM. 3. Doub le-click the “Mac OS 9” folder . 4. Doub le-click “USB Reader_Writer”.
34 < Mac OS 8.6~9.2 ⽧ Install > 6. Click the “Restart” button. The device driver is now installed. (Remove the CD-ROM from the CD-ROM drive and store it in a safe place.) 5. When the Mac OS 8.x, 9.x installer starts up, the window at right appears.
35 Operating the MAUSB-10 The operating procedure for the MAUSB-10 under Mac OS is described below . 1 Connecting to the computer <Mac OS 8.6~9.2 ⽧ Operation> After installing the device driver , connect the MAUSB-10’ s connector to the USB port on your computer .
36 2 Inserting a card <Mac OS 8.6~9.2 ⽧ Operation> 1. Make sure the MAUSB-10 is connected to the computer and insert the card into the corresponding card slot. [xD-Picture Card] Make sure the card is level and that the gold-colored contact area is facing down .
37 3 Removing a card <Mac OS 8.6~9.2 ⽧ Operation> Close all software programs that are using data on the card (e. g. graphics applications), then follow the steps below . Attention! If you do not follow the steps below , the data on the card(s) may be damaged.
38 4 Copying files from a card <Mac OS 8.6~9.2 ⽧ Operation> 1. Insert a card in the MAUSB-10. * The status lamp blinks, then the card icon appears on the desktop. * The icon’s appearance may vary , depending on the card and the OS version. 2.
39 How to uninstall the device driver <Mac OS 8.6~9.2> The device driver can be deleted if it is no longer needed. First make sure that the MAUSB-10 is disconnected from the computer’s USB port, then follow the steps below . 1. From the desktop, double-click the hard disk icon.
40 How to install Also refer to your computer ’s user manual and the manuals for any optional devices you are using. 1 T ur n on the computer <Mac OS X ⽧ Install> T urn on your computer’s power (and connected devices) to start Mac OS.
41 3 Install the device driver <Mac OS X ⽧ Install> When using the MAUSB-10 for the first time, you must first install the device driver included on the provided CD-ROM. 1. Doub le-click the “OL YMPUS” icon. 2. Doub le-click the “MAUSB-10” folder .
42 < Mac OS X ⽧ Install > 6. Enter the administrator ’ s name and the pass- word, then click the “OK” button. 7. Click the “Continue” button. 8. Click the “Continue” button. 9. Select the disk to install on, then click the “Continue” button.
43 < Mac OS X ⽧ Install > 10. Click the “Install” (or “Upgrade”) button. 11. Click the “Continue Installation” button. 12. The window at right appears during the installation. 13. Click the “Restart” button. The device driver is now installed.
44 Operating the MAUSB-10 The operating procedure for the MAUSB-10 under Mac OS is described below . 1 Connecting to the computer <Mac OS X ⽧ Operation> After installing the device driver , connect the MAUSB-10’ s connector to the USB port on your computer .
45 2 Inserting a card <Mac OS X ⽧ Operation> 1. Make sure the MAUSB-10 is connected to the computer and insert the card into the corresponding card slot. [xD-Picture Card] Make sure the card is level and that the gold-colored contact area is facing down .
46 3 Removing a card <Mac OS X ⽧ Operation> Close all software programs that are using data on the card (e. g. graphics applications), then follow the steps below . Attention! If you do not follow the steps below , the data on the card(s) may be damaged.
47 4 Copying files from a card <Mac OS X ⽧ Operation> 1. Insert a card in the MAUSB-10. * The status lamp blinks, then the card icon appears on the desktop. * The icon’ s appearance may vary , depending on the card and the OS version. 2. Double-click the icon to display the files that you want to copy .
48 T roubleshooting Windows The status lamp (green) does not light. A “Found New Hardware Wizard” windo w appears when you connect the MAUSB-10. The MAUSB-10 doesn’t work even after installing the driver and connecting the MAUSB-10 to the computer .
49 T roubleshooting Macintosh The status lamp (green) does not light. No card icon(s) appears on the computer’ s screen. Y ou can read a card, but not write to it. Y ou cannot write with a SmartMedia. The error message “File Sharing is invalid.” appears.
50 Specifications * The specifications in this manual are subject to change without prior notice. * For the latest information, visit the OL YMPUS web site (http://www .olympus.com). * 1 Some cards with ID are not generally available for purchase. Consult your nearest SmartMedia dealer for details.
51 Glossary of T er ms A program used to operate or manage a peripheral device (printer , modem, digital camera, USB reader/writer , etc.). Without the proper driver installed, a peripheral device will not be recognized by the computer . A window that appears on the monitor when the computer requires user confirmation or instructions on what to do.
OL YMPUS OPTICAL CO ., L TD. VT398703.
An important point after buying a device Olympus MAUSB-10 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Olympus MAUSB-10 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Olympus MAUSB-10 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Olympus MAUSB-10 you will learn all the available features of the product, as well as information on its operation. The information that you get Olympus MAUSB-10 will certainly help you make a decision on the purchase.
If you already are a holder of Olympus MAUSB-10, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Olympus MAUSB-10.
However, one of the most important roles played by the user manual is to help in solving problems with Olympus MAUSB-10. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Olympus MAUSB-10 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
