Instruction/ maintenance manual of the product POCKET PRINT 6010E Oki
Go to page of 230
OkiLAN 6010e P oc ket Print Ser ver User’ s Guide High P erformance Ethernet Netw ork Print Server.
ii Copyright and T rademark Information OKI OkiLAN 6010e User’ s Guide Printing History Ev ery ef fort has been made to ensure that the information in this document is complete, accurate, and up-to-date. Okidata assumes no responsibility for the results of errors be yond its control.
iii Or ganization and Contents OKI OkiLAN 6010e User’ s Guide Or ganization This manual has been di vided into f iv e sections. Section I contains installation instructions for the OkiLAN 6010e Pocket Print Serv er .
iv Or ganization and Contents OKI OkiLAN 6010e User’ s Guide Section III: NetW are Chapter 1: Introduction ................................................... III-5 Chapter 2: OkiNet for NetW are ....................................... III-8 Chapter 3: OkiNet for NDS .
v Network Operating Systems OKI OkiLAN 6010e User’ s Guide Netw ork Operating Systems Over view OkiLAN 6010e simultaneously supports se veral network protocols in v arious combinations. Below is a list of sup- ported network protocols accompanied with NOS/OS requirements.
vi T echnical Support OKI OkiLAN 6010e User’ s Guide Ser vice Inf ormation This information is valid for the United States and Canada only . OKID A T A Online V isit the OKID A T A W e b Site at http://www .
vii T echnical Support OKI OkiLAN 6010e User’ s Guide The Okidata Customer Suppor t Center For customer ser vice, call 1-800-OKID A T A (800-654-3282).
viii T echnical Support OKI OkiLAN 6010e User’ s Guide F axable F acts Y ou can hav e product and support infor mation fax ed automatically to you through Okidata’ s Faxable F acts, an online document retrie v al system. A touch-tone telephone and facsimile machine with a designated telephone number are required.
ix T echnical Support OKI OkiLAN 6010e User’ s Guide MEXICO Oki Data de Mexico, S.A. de C.V . T el: 525-661-6860 Fax: 525-661-5861 ARGENTIN A Me gatech T el: (541)-371-4123 F ax: (541)-371-4123 [T ouch-T one © required] CHILE T eknos Communicaciones T el: 56 (2) 555 5530 Fax: 56 (2)550 2390 VENEZUELA MAI de V enezuela S.
x T echnical Support OKI OkiLAN 6010e User’ s Guide When you call Customer Support Center , the follo wing information will help us answer your questions more quickly and accurately .
Har dware Installation Section I: Har dware Installation.
.
Har dware Installation I - 3 Section I - Har dwar e Installation OKI OkiLAN 6010e User’ s Guide In This Section Po wering On the OkiLAN 6010e .......
I - 4 Section I - Har dwar e Installation OKI OkiLAN 6010e User’ s Guide.
Har dware Installation I - 5 Section I - Har dwar e Installation OKI OkiLAN 6010e User’ s Guide The OkiLAN 6010e Pocket Print Server enables Ethernet network users to connect to a printer with a bidirectional parallel port.
I - 6 Section I - Har dwar e Installation OKI OkiLAN 6010e User’ s Guide 3. Secure the OkiLAN 6010e with the wire clips on the printer’ s connector . 4. Plug the po wer adapter wir e into the po wer jack on the OkiLAN 6010e. Then plug the po wer adapter into a wall outlet.
Har dware Installation I - 7 Section I - Har dwar e Installation OKI OkiLAN 6010e User’ s Guide 5. Attach the 10Base-T UTP cable to the receptacle on the back of the OkiLAN 6010e. Attach the other end of the cable to the Network. P owering On the OkiLAN 6010e T urn printer po wer on.
I - 8 Section I - Har dwar e Installation OKI OkiLAN 6010e User’ s Guide Note: If Status Indicator does not display as indicated abo v e, see Hardwar e T roubleshooting at the end of this section. Printing a Configuration Sheet T o print configuration information, press the T est b utton on the side of the OkiLAN 6010e.
Har dware Installation I - 9 Section I - Har dwar e Installation OKI OkiLAN 6010e User’ s Guide Installing the OkiLAN Utilities Software in Windows 1. Insert the OkiLAN CD into your CD-R OM dri ve. 2. The Setup screen appears automatically (if it doesn’ t, click Start → Run, then enter D:setup, if “D” is your CD-R OM dri ve).
I - 10 Section I - Har dwar e Installation OKI OkiLAN 6010e User’ s Guide TCP/IP Management Utilities OkiNet Utilities for TCP/IP OkiNet Alert for TCP/IP Okidata MIB BootP Serv er Note: The OkiLAN Utilities CD is designed for more than one type of OkiLAN print serv er and includes features that do not apply to the OkiLAN 6010e.
Har dware Installation I - 11 Section I - Har dwar e Installation OKI OkiLAN 6010e User’ s Guide Solution a) Unplug the OkiLAN 6010e po wer adapter from the wall outlet. Remo ve the network cable. Plug the network cable back in until you hear a positi ve click.
I - 12 Section I - Har dwar e Installation OKI OkiLAN 6010e User’ s Guide F ailing the self test can be caused by an y of the follow- ing: a) The printer is malfunctioning. Unplug the OkiLAN 6010e from the printer and unplug the po wer adapter . Reconnect the OkiLAN 6010e and the po wer adapter .
Adv anced Management Section II: Adv anced Mana g ement Features.
.
Adv anced Management II - 3 Section II - Advanced Management F eatur e s OKI OkiLAN 6010e User’ s Guide In This Section Chapter 1: SNMP ................................. II-5 Ov erview ...................................................... II-5 Pri v ate MIB .
II - 4 Section II - Advanced Management F eatur e s OKI OkiLAN 6010e User’ s Guide Reset .......................................................... II-22 OkiLAN 6010e Server Disco very ............. II-23 T r oubleshooting ..........................
Adv anced Management II - 5 Section II - Advanced Management F eatur e s OKI OkiLAN 6010e User’ s Guide Chapter 1: SNMP Over view Simple Network Management Protocol (SNMP) pro- vides network administrators with the ability to com- municate management functions between an SNMP manager and an SNMP agent.
II - 6 Section II - Advanced Management F eatur e s OKI OkiLAN 6010e User’ s Guide The setting of certain v ariables causes an immediate f irmware r eset. These variables are listed in the pri v a te MIB under cmdReset . Note: If you attempt a reset while a job is printing, the job may not print successfully .
Adv anced Management II - 7 Section II - Advanced Management F eatur e s OKI OkiLAN 6010e User’ s Guide The OkiLAN 6010e sends printer traps when there is a change in the status of the printer . If the printer goes of f-line, runs out of paper or is detached, the adminis- trator will be notified via the OkiLAN 6010e traps o v er both UDP and IPX.
II - 8 Section II - Advanced Management F eatur e s OKI OkiLAN 6010e User’ s Guide Both the OkiNet for TCP/IP and the IPX, and the OkiLAN 6010e Conf iguration utility (telnet) allo w you to specify the community names and a trap destination IP address.
Adv anced Management II - 9 Section II - Advanced Management F eatur e s OKI OkiLAN 6010e User’ s Guide Chapter 2: HP JetAdmin Suppor t Over view This section contains instructions and information on ho w to configure and obtain diagnostic information from your OkiLAN 6010e using the He wlett-Packard JetAdmin software.
II - 10 Section II - Advanced Management F eatur e s OKI OkiLAN 6010e User’ s Guide 5. If you are running a NetW are 4.x network, click the NetW ar e Dir ectory Services icon from the left column. Select NDS T r ee Name from the pull-do wn menu and enter the Print Serv er Context .
Adv anced Management II - 11 Section II - Advanced Management F eatur e s OKI OkiLAN 6010e User’ s Guide Obtaining Diagnostic Inf ormation Using JetAdmin 1. From the main JetAdmin screen, select the OkiLAN 6010e port on which you wish to vie w diagnostic information.
II - 12 Section II - Advanced Management F eatur e s OKI OkiLAN 6010e User’ s Guide Chapter 3: HP W eb JetAdmin Suppor t Over view This section contains instructions and information on ho w to conf igure , install, and obtain diagnostic infor - mation from your OkiLAN 6010e using the He wlett- Packard W e b JetAdmin software.
Adv anced Management II - 13 Section II - Advanced Management F eatur e s OKI OkiLAN 6010e User’ s Guide Installing a Windows NT Printer f or the OkiLAN 6010e 1. From the main W eb J etAdmin page, select the OkiLAN 6010e port you wish to install. 2.
II - 14 Section II - Advanced Management F eatur e s OKI OkiLAN 6010e User’ s Guide Obtaining Diagnostic Inf ormation fro m the OkiLAN 6010e 1. From the main W eb J etAdmin page, select the OkiLAN 6010e port on which you wish to vie w diagnostic information.
Adv anced Management II - 15 Section II - Advanced Management F eatur e s OKI OkiLAN 6010e User’ s Guide Chapter 4: OkiLAN 6010e W eb Configuration Over view This section contains instructions and information on ho w to configure and manage your OkiLAN 6010e using a standard W eb browser .
II - 16 Section II - Advanced Management F eatur e s OKI OkiLAN 6010e User’ s Guide Connecting to the OkiLAN 6010e 1. Enter <http://HTTP Address> in the bro wser address prompt. The HTTP address can be the IP address, the System Name if the print serv er has been conf igured to use WINS , or the DNS name if registered with a DNS server .
Adv anced Management II - 17 Section II - Advanced Management F eatur e s OKI OkiLAN 6010e User’ s Guide 2. A successful connection will display the print serv er home page. Note: By default, only Status and Support information can be viewed. T o configure the print server , see the Conf igur ation section .
II - 18 Section II - Advanced Management F eatur e s OKI OkiLAN 6010e User’ s Guide Configuration 1. Select the Login as Admin link under the Conf igur ation menu. 2. On the Enter Network P asswor d screen, enter the User name and P assw or d . The default administrator User name is admin .
Adv anced Management II - 19 Section II - Advanced Management F eatur e s OKI OkiLAN 6010e User’ s Guide 5. A Request Results page will appear indicat- ing one of the follo wing: • Conf iguration Successfull y Set: The v alues hav e been successfully sav ed to the print serv er .
II - 20 Section II - Advanced Management F eatur e s OKI OkiLAN 6010e User’ s Guide * The follo wing values are currently only configurable through the W eb bro wser interface: W eb Admin Conf iguration Under the Conf iguration menu, select the Admin(W eb) link.
Adv anced Management II - 21 Section II - Advanced Management F eatur e s OKI OkiLAN 6010e User’ s Guide • Custom Link Title – This f ield is useful for setting up a link to an internal help desk. If conf igured, it will appear under the Support menu.
II - 22 Section II - Advanced Management F eatur e s OKI OkiLAN 6010e User’ s Guide Updates By default this link will connect you to the f irmw are update location on the Okidata FTP Serv er . This link can be conf igured to point to other locations by select- ing the Admin(W eb) link under the Conf iguration menu.
Adv anced Management II - 23 Section II - Advanced Management F eatur e s OKI OkiLAN 6010e User’ s Guide OkiLAN 6010e Ser ver Disco very An HTML f ile containing links to all OkiLAN 6010e print serv ers on the netw ork can be created using the OkiNet utility for TCP/IP .
II - 24 Section II - Advanced Management F eatur e s OKI OkiLAN 6010e User’ s Guide T roubleshooting Serv er Connection • The print server only supports tw o simulta- neous HTTP connections. If your bro wser fails to connect to the print serv er , the bro wser may be tr ying to open more than two connections.
Adv anced Management II - 25 Section II - Advanced Management F eatur e s OKI OkiLAN 6010e User’ s Guide Login • If you forget the administrator password, restoring the TCP/IP protocol to factory defaults from an y other conf igura tion utility restores the W eb admin name and pass word to default v alues.
II - 26 Section II - Advanced Management F eatur e s OKI OkiLAN 6010e User’ s Guide Chapter 5: Additional Management Features OkiNet Aler t OKI OkiNet Alert enterprise management utility allows administrators to proacti v ely manage printers by being immediately alerted to printing problems before they are encountered by users.
Adv anced Management II - 27 Section II - Advanced Management F eatur e s OKI OkiLAN 6010e User’ s Guide OkiNet f or NDS OkiNet for NDS allo ws administr a tors to create and manage OKI print serv er objects in the NDS tree. OkiNet for NDS inte grates into Nov ell’ s NetW are Administrator , NetW areAdmin.
II - 28 Section II - Advanced Management F eatur e s OKI OkiLAN 6010e User’ s Guide Windo ws Printing From a W indo ws oper ating system, using TCP/IP or DLC protocols, the OkiNet Connect utility routes the print job to the appropriate printer without passing through a f ile serv er or print queue.
NetW are Section III: NetW are.
.
NetW are III - 3 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide In This Section Chapter 1: Introduction ...................... III-5 Ov erview ..................................................... III-5 Before Y ou Start ....................
III - 4 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide Modifying V ie w Settings .......................... III-24 Permanently Def ining SNMP Access Information .......................................... III-27 Chapter 3: OkiNet for NDS ....
NetW are III - 5 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide Chapter 1: Intr oduction Over view This section contains instructions and information on ho w to configure your OkiLAN 6010e in the NetW are en vironment. There are two en vironments in which to configure the OkiLAN 6010e: • Bindery (NetW are 3.
III - 6 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide Selecting PServer or RPrinter/NPrinter Mode Y our OkiLAN 6010e supports both PServer and NPrinter mode. There are se veral f actors to consider when choosing which mode to use. In PServ er mode, the OkiLAN 6010e operates as the print serv er .
NetW are III - 7 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide e r u t a e Fe d o M r e v r e S P r e t n i r P N / r e t n i r P R e d o M r e v r e S t n i r P t n i r p e t a r a p e S , e d o n r e v r e s r e v r e s t n i r p d n a , s n o i t c n u f t n i r p e r a W t e N e r a w t f o s r e v r e s .
III - 8 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide Chapter 2: OkiNet f or NetW are Over view This chapter contains information about how to conf ig- ure the OkiLAN 6010e in Bindery and NDS en viron- ments using the OkiNet for NetW are utility .
NetW are III - 9 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide By default, the All Print Servers vie w is selected and all print serv ers attached to the network from which the OkiNet utility is running are listed. Configuring the OkiLAN 6010e Using OkiNet f or NetW are The follo wing steps outline ho w to conf igur e an OkiLAN 6010e.
III - 10 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide The follo wing settings are conf igurable based on the capabilities of the OkiLAN 6010e: • NetW are • NetW are Queues • NetW are.
NetW are III - 11 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide PServ er or RPrinter Mode Se veral factors should be considered when choosing between PServ er or RPrinter mode. F or more detailed information regarding these modes, see page III-4.
III - 12 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide Example: cn=marketinglj.ou=mark eting.o=companyname where cn is the Common Name of the leaf object, ou is the Or ganizational Unit name , and o is the Organiza- tional name.
NetW are III - 13 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide TCP/IP Configuration Options T o modify conf igura tion settings specif ic to the TCP/IP protocol such as IP address, subnet mask and default gate w ay .
III - 14 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide Name Field Enter a descripti v e name to identify the port. Language Switching Each output port can be configured to perform the follo wing language switching options: OFF , PCL, PostScript or Automatic.
NetW are III - 15 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide Printer T ype The Printer T ype selection is used to deter mine the actual character string required for your printer . If y our printer type is not listed, select Other and enter the character string for switching the printer to PCL or PostScript mode.
III - 16 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide SNMP Configuration Options SNMP options specify which information is necessary for an SNMP manager to access the OkiLAN 6010e. The system v ariables are for user con v enience and are optional.
NetW are III - 17 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide Fill in the follo wing information: System Name Enter the name of your choice. This name will identify the OkiLAN 6010e in your SNMP-based management program. System Contact Enter any information useful to a user if problems with the OkiLAN 6010e arise.
III - 18 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide T rap Community Name Enter the community name which will be used when traps are sent from the OkiLAN 6010e. This setting allo ws trap utilities to onl y accept tr aps from de vices with appropriate community names.
NetW are III - 19 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide Fill in the follo wing information: Protocol Select the protocol for which you wish to conf igure trap information. T rap Destination • NetW are Protocol – Enter the network number and hardware address, respecti v ely , to which traps will be sent.
III - 20 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide Printer T raps Select the printer traps to be acti v ated. The follo wing printer conditions may cause a printer trap to occur: • On.
NetW are III - 21 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide Displa ying OkiLAN 6010e Diagnostic Inf ormation T o vie w OkiLAN 6010e diagnostic informa tion, select Diagnostics from the Print Server pull-do wn menu on the main NetW ar e Print Manager screen.
III - 22 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide Restoring F actor y Default Settings T o restore the OkiLAN 6010e to factory default set- tings, select the OkiLAN 6010e from the list of a vail- able print serv ers. From the Print Server menu bar , select the Reset option.
NetW are III - 23 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide Creating Customized Views OkiNet for NetW are allo ws users to create multiple customized vie ws for the list of OkiLAN 6010e prod- ucts. By creating dif ferent vie ws, the user can narrow the information displayed to that which is of highest priority .
III - 24 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide Modifying Vie w Settings Before modifying the settings, select the name of the vie w you wish to edit from the Name field. Display Filter The filter option displays only those print serv ers matching specific criteria.
NetW are III - 25 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide Mode The NetW are mode the print server is running Network # The IPX network number Sear ch Filter The Search option def ines the criteria for locating OkiLAN 6010e products on the network.
III - 26 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide Columns Column information for each pr int serv er can be modi- f ied. T o def ine the location of a ne w column, select the location in the Columns Displayed f ield where you wish the ne w column to be inser ted, then select Ad d .
NetW are III - 27 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide P ermanently Defining SNMP Access Inf ormation Access to OkiLAN 6010e conf iguration and diagnostic information is determined by using community names.
III - 28 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide Add Select the Ad d button to def ine access to a ne w OkiLAN 6010e or a group of OkiLAN 6010e products. Enter a serial number or a netw ork number follo wed by a dash (-). Use an asterisk (*) as a wildcard to match multiple de vices.
NetW are III - 29 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide Chapter 3: OkiNet f or NDS Over view OkiNet for NDS is a Dynamic Link Library (DLL) which allo ws users to create and manage OKI print serv er objects in the NDS tree.
III - 30 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide • The OkiNet for NDS installation for NetW are version 4.11 requires a se parate installation for each of the three platforms: W indows 3.x, W indo ws 95 and/or W indo ws NT (three separate versions of NW Admin).
NetW are III - 31 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide Installing OkiNet f or NDS f or Novell NetW are 4.1 A single installation is required to service W indows 3.x and W indows 95 operating systems with OkiNet for NDS for Nov ell NetW are 4.
III - 32 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide Installing OkiNet f or NDS f or Novell NetW are 4.11 and Windo ws 3.x OkiNet for NDS must be installed in the same location you ha v e installed NetW are Administrator . This may be located on the f ile serv er or on an inde pendent worksta- tion.
NetW are III - 33 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide Installing OkiNet f or NDS f or Novell NetW are 4.11 and Windo ws 95/Windows NT OkiNet for NDS must be installed in the same location you ha v e installed NetW are Administrator .
III - 34 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide Installing OkiNet f or NDS f or Novell NetW are 4.11 and Windo ws 95/Windows NT OkiNet for NDS must be installed in the same location you ha v e installed NetW are Administrator . This may be located on the f ile serv er or on an inde pendent worksta- tion.
NetW are III - 35 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide Creating a Ne w OkiLAN 6010e Object T o create a ne w OkiLAN 6010e object from Nov ell’ s NetW are Administrator , perform the following ste ps: 1. Select the container (also kno wn as or gani- zational unit) in which you want the object created.
III - 36 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide 6. Click OK . Note: If the Device list box is still empty , select Find Device . This will allo w you to locate the specific de vice you are trying to def ine. Y ou will be prompted for the Ethernet address and network number of the de vice.
NetW are III - 37 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide 3. Open the OKI Print Serv er object’ s Details dialog. This may be done by double-clicking on the OKI print serv er icon in the NDS tree or by selecting Details from the F ile menu.
III - 38 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide 11. Select or create a NetW ar e Print Ser v er object from the Assignments page . 12. Select a port to configure from the Assign- ments page, then select Assign . 13. Select or crea te a NetW are Printer object from the Printer/Queue Assignments dialog.
NetW are III - 39 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide The follo wing settings are configurable: • Identif ication • Network Protocols • Assignments • Port Configuration • Network Conf iguration • Status F or specif ic information about these detail pages, select the HELP b utton.
III - 40 Section III - NetW ar e OKI OkiLAN 6010e User’ s Guide The install utility on the installation diskette can also be used to remov e the OKI print server class. This utility remov es the c lass from Nov ell’ s NetW are Administrator and remov es all the associa ted f iles that were copied during the installation process.
TCP/IP Section IV : TCP/IP.
In This Section Chapter 1: Intr oduction ...................... IV -6 Overvie w ..................................................... IV -6 Software Requirements .............................. IV -6 Netw ork Preparation ...............................
TCP/IP IV - 3 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Running OkiNet for TCP/IP ..................... IV -29 Conf iguring the OkiLAN 6010e Using OkiNet for TCP/IP ............................... IV -30 Conf iguring TCP/IP Options ........
IV - 4 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Changing the Passw ord (Option 2) .......... IV -55 Specify Print Server IP Address (Option 3) ............................................ IV -55 Specify the Subnet Mask for Y our Netw ork (Option 4) .
TCP/IP IV - 5 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Conf iguring HP-UX v9.xx for Printing with the OkiLAN 6010e .................................... IV -84 Conf iguring HP-UX v10.xx for Printing with the OkiLAN 6010e ...................
IV - 6 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Chapter 1: Introduction Over view This section contains instructions and information on ho w to conf igure your OkiLAN 6010e. Y ou will also be instructed on ho w to set up your host computers to print to the OkiLAN 6010e using the TCP/IP protocol.
TCP/IP IV - 7 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Netw ork Preparation • Y ou should be familiar with network admin- istration as well as the physical setup and operation of your network. • Advise users of possible disruption during installation.
IV - 8 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Overview of TCP/IP Configuration • Assign an IP address for the OkiLAN 6010e • Conf igure the OkiLAN 6010e network information • Conf .
TCP/IP IV - 9 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Chapter 2: Configuring the OkiLAN 6010e Choosing an IP Address Ever y TCP/IP network de vice is r equired to hav e a unique IP address.
IV - 10 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide 2. Add the name and IP address to the “/etc/ hosts” f ile of each host that will access the OkiLAN 6010e. Or , if your network uses a name service, add the host name and IP address to the name server .
TCP/IP IV - 11 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Assigning the IP Ad dress There are eight dif ferent methods for assigning an IP address to the OkiLAN 6010e: Gleaning, Static Route Entry , DHCP , RARP , BOO TP and using the OkiNet utilities.
IV - 12 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide 2. Start a continuous ping to the OkiLAN 6010e. ping < ip_addr ess > Example: ping 192.168.42.24 On some systems, this may require an additional pa- rameter . Some implementations of ping only send out one ping packet which could get lost in transit.
TCP/IP IV - 13 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide DHCP of f ers dynamic IP address allocation. When a client recei ves an IP address, it also recei v es a lease (an amount of time the host may use the address). The lease times v ary from 1 hour to 100 years, or may be infinite.
IV - 14 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Static Route Entry When the OkiLAN 6010e is po wered on or reset and no permanent IP address has been assigned, it will attempt to obtain an IP address through Gleaning, RARP , BOO TP or DHCP .
TCP/IP IV - 15 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide RARP or BOO TP If an IP address has not been permanently assigned, the OkiLAN 6010e will use Re verse Address Resolution Protocol (RARP) or Bootstrap Protocol (BOO TP). The OkiLAN 6010e will broadcast requests for its IP ad- dress to both RARP and BOO TP servers.
IV - 16 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Other Utilities The IP address can also be set from Nov ell NetW are using the OkiNet for NetW are utility . Note: The OkiNet for NetW are utilities can only be used if Nov ell NetW are is installed on your network.
TCP/IP IV - 17 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Chapter 3: TCP/IP Configuration and Printing Over view The OkiLAN 6010e supports printing from computers using TCP/IP and an y of th.
IV - 18 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Configuring f or TCP/IP Netw ork Printing Most computers that support TCP/IP network printing use the Remote Line Printer Daemon (LPD) protocol. This protocol was originally part of the Berkele y Soft- ware Distrib ution (BSD) version of the UNIX operating system.
TCP/IP IV - 19 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide The OkiLAN 6010e is designed to handle many dif fer- ent types of printers and print data. T ypically you will select the printer type for your printer in telnet under the Conf igur e Po r t option.
IV - 20 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide In addition to the f or m feed described abo v e , the OkiLAN 6010e inserts a carriage-retur n character into the print job immediately bef or e each line-feed character . This featur e is useful f or printing UNIX text f iles.
TCP/IP IV - 21 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide The entry should be similar to the follo wing: local_print_queue_name | [printer_model_and_manufactur er]: :lp=:mx#0:rm=OkiLAN 6010e.
IV - 22 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide log_f ile_name This is the path to a f ile where error information from the lpd will be logged.
TCP/IP IV - 23 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Remote LPD Printing The way print jobs are queued to a Remote LPD system v aries among the vendors that support TCP/IP . UNIX systems that are BSD-based typically use the lpr pro- gram to submit print jobs.
IV - 24 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide The OkiLAN 6010e recognizes the follo wing FTP commands: PUT Print a single f ile The PUT command sends the f ile to the OkiLAN 6010e. The f irst parameter of the PUT command is the name of the local f ile to PUT .
TCP/IP IV - 25 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide MODE Specif ies transfer mode. Stream is the only transfer mode sup- ported. OPEN Opens connection to remote host. CLOSE T erminates FTP session. QUIT T erminates FTP session and e xits FTP .
IV - 26 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide $ ftp OkiLAN 6010e_name<Enter> Connected to OkiLAN 6010e_name. 220 ESI-2810 V e rsion 3.0 ready . Name (OkiLAN 6010e_name:an yone):<Enter> 230 User logged in. ftp> binary<Enter> 200 T ype set to I.
TCP/IP IV - 27 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Ra w P or t Printing Host computer software can use a raw TCP/IP port connection to send data to the OkiLAN 6010e.
IV - 28 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Chapter 4: OkiNet f or TCP/IP Over view This section contains information about OkiNet for TCP/IP . OkiNet for TCP/IP pro vides SNMP-based support for the entire OkiLAN 6010e family of print ser ve rs.
TCP/IP IV - 29 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide OkiNet for TCP/IP requir es that the TCP/IP protocol is running using a W insock (W indows Sockets) TCP/IP stack, v ersion 1.
IV - 30 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Configuring the OkiLAN 6010e Using OkiNet f or TCP/IP The follo wing steps outline ho w to conf igur e an OkiLAN 6010e. T o change settings of a pre viousl y conf igured OkiLAN 6010e, follo w the same procedure b ut skip Step 3, as no prompt will appear .
TCP/IP IV - 31 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Configuring TCP/IP Options T o conf igure options specific to the TCP/IP protocol, select the TCP/IP tab .
IV - 32 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Fill in the follo wing information: IP Addr ess Resolution • Set P ermanent – Select this option to make the IP address permanent. If the OkiLAN 6010e has been conf igured to remember its IP address, it does not need to determine its address each time it is po w- ered on.
TCP/IP IV - 33 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Default Gateway If your local network is attached to other netw orks, you can specify the address of your default gatew a y . This gate w ay will be selected whene ver messa ges need to be sent to another network.
IV - 34 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide NetW are and NetW are P or t Configura- tion Options For specif ic information on NetW are or NetW are Port options, see Section III, Novell NetW ar e , or select the HELP b utton on the bottom right of the screen.
TCP/IP IV - 35 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide P ort Number Select the port number you wish to conf igure. Name Field Enter a descripti ve name to identify the port. Language Switching Each output port can be configured to perform the follo wing language switching options: OFF , PCL, PostScript or Automatic.
IV - 36 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide • OFF – Print data stream will be sent directly to the output port without alteration. • PCL – Inserts the appropriate character string in front of each print job to switch the printer to the PCL print language.
TCP/IP IV - 37 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide P ostScript Switch Sequence Enter the character string to switch the printer to the PostScript print language. Conf iguration Page Language Select the appropriate printer language for printing conf iguration pages on your printer .
IV - 38 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Note: SNMP options need to be conf igured only if you are managing an OkiLAN 6010e or getting system information using SNMP . System Name Enter the name of your choice. This name will identify the OkiLAN 6010e in your SNMP-based management program.
TCP/IP IV - 39 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Get Community Name This f ield is used to set the community name required to Get information from the print serv er . The default community name is public . Note: F or JetAdmin to function correctly with the OkiLAN 6010e, the SNMP Get and Set community name must be set to public .
IV - 40 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Enabling/Disabling Pr otocols T o enable or disable protocols on the OkiLAN 6010e, select the Pr otocols tab . Select each protocol you wish to enable. If you disable a protocol, the OkiLAN 6010e will no longer communicate using that protocol.
TCP/IP IV - 41 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Protocol Select the protocol for which you wish to conf igure trap information. T rap Destination • TCP/IP Protocol – Enter the IP address to which traps will be sent. The IP address must follo w the format XXX.
IV - 42 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Printer T raps Select the printer traps to be acti v ated. The follo wing printer error conditions may cause a printer trap to occur: • O.
TCP/IP IV - 43 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Displa ying OkiLAN 6010e Diagnostic Inf ormation T o vie w OkiLAN 6010e dia gnostic information, double click on Diagnostics from the Print Server pull-do wn menu on the main OkiNet TCP/IP screen.
IV - 44 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Restoring F actor y Default Settings T o restore the OkiLAN 6010e to factory default set- tings, select the OkiLAN 6010e from the list of a vail- able print serv ers. From the Print Server menu bar , select Reset .
TCP/IP IV - 45 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Creating Customized Views OkiNet for TCP/IP allo ws users to create multiple customized vie ws for the list of OkiLAN 6010e prod- ucts. By creating dif ferent vie ws, the user can narrow the information displayed to that which is of highest priority .
IV - 46 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Selecting an Existing V ie w T o select an e xisting vie w , choose Select from the Vi e w menu. Highlight the vie w you wish to open and select OK . The OkiLAN 6010e list will be displayed as described by the vie w selected .
TCP/IP IV - 47 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide H/W Address 12 he xadecimal digits for the Ethernet address IP Address XXX.XXX.XXX.
IV - 48 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide • Specify Devices/Netw orks – This method adds specif ic print serv e rs (or groups of print serv e rs) to the list. If you ha v e OkiLAN 6010e print servers that are not on the local network (i.
TCP/IP IV - 49 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide For e xample, if you currently hav e three columns displayed and you wish to add a fourth column to the far left of the screen, follo w these steps: 1. Select the f irst column in the Columns Displayed f ield.
IV - 50 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide P ermanently Defining SNMP Access Inf ormation Access to OkiLAN 6010e conf iguration and diagnostic information is determined by using community names.
TCP/IP IV - 51 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Add Select the Ad d button to def ine access to a new OkiLAN 6010e or a group of OkiLAN 6010e print serv ers. The IP address must follo w the forma t XXX.XXX.XXX.XXX, where each XXX is a number from 0 to 255.
IV - 52 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Star ting a T elnet Session A simple telnet interface has been pro vided to commu- nicate with de vices suppor ting telnet. A telnet session can be started by selecting the OkiLAN 6010e from the print serv er list and choosing the T elnet Session option from the T ools menu.
TCP/IP IV - 53 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Chapter 5: T elnet Configuration Over view The OkiLAN 6010e Conf iguration utility ( telnet ) provides system, netw ork and printer status information and allo ws you to change the conf iguration of your OkiLAN 6010e.
IV - 54 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide 3. When you are finished typing your pass- word, press Enter . F or password v erifica- tion, you will then be ask ed to enter your password again. Each time you use the utility , you will be asked to enter your password.
TCP/IP IV - 55 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Sho wing Network/Printer Inf ormation (Option 1) This option displays current network and printer infor - mation. Changing the P assw or d (Option 2) This option allo ws y ou to change the passw or d required for access to this utility .
IV - 56 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Remember , when choosing a permanent IP address: • The IP address must follo w the format XXX.XXX.XXX.XXX, where each XXX is a number between 0 and 255. • If you select an in v alid IP address you may not be able to access the OkiLAN 6010e.
TCP/IP IV - 57 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide If you change the subnet mask, the change will remain undetected until the OkiLAN 6010e is reset or is po wer c ycled. Note: If you select an in valid subnet mask you may not be able to access the OkiLAN 6010e.
IV - 58 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Configure P or t (Option 6) After the Conf igure menu appears, you can access the follo wing conf iguration option screens.
TCP/IP IV - 59 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide TCP Connection Configuration (Option 7) TCP Connection T imeout This is used to se ver network TCP/IP Connections tha t are idle for more than a specif ied per iod of time (be- tween 1 and 3600 seconds).
IV - 60 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Restore to F actory Default Configuration (Option 9) This option automatically restores the OkiLAN 6010e to its original factory defaults.
TCP/IP IV - 61 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Appendix A: T r oub leshooting Main Status Indicator Upon po wer -up, the main status indicator flashes orange. It changes to green when the OkiLAN 6010e passes self-test. The indicator stays orang e if the OkiLAN 6010e fails self-test.
IV - 62 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Unable to Assign IP Ad dress Gleaning If you ping the de vice and are not g etting a response, the glean is not working. Check the follo wing possible problems: • V erify the ARP table contains the correct hardware and IP address by running the ‘ arp –a ’ command.
TCP/IP IV - 63 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide RARP or BOO TP If you are using a BOO TP or RARP serv er and the OkiLAN 6010e is not getting an IP address, check the follo wing: .
IV - 64 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide • Some BOO TP serv ers will write their internal bootptab tables to a f ile when the y recei v e a SIGUSR1 signal. Y ou can check this f ile to v erify the hardware and IP ad- dress are correct.
TCP/IP IV - 65 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide • V erify the OkiLAN 6010e is on the same subnet as the host from which you are telneting . As a drastic measure, try creating an isolated subnet with your host and the OkiLAN 6010e.
IV - 66 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide OkiNet f or TCP/IP – Winsock Err o rs • If you see an error before OkiNet for TCP/IP appears on the screen, try setting a host name in the hosts f ile in the W indo ws directory (check the documentation for your W indo ws TCP/IP stack).
TCP/IP IV - 67 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide If you find the ca ble is connected and you are still recei ving this messa ge or any other “ST :” error mes- sage, power c ycle the OkiLAN 6010e. If the error continues, call Okidata Customer Support at 1-800-OKID A T A (1-800-654-3282).
IV - 68 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide If you do not kno w the conf iguration of the OkiLAN 6010e or you think the conf iguration has been chang ed, use the follo wing method for printing a configuration page: • W ith the network cable detac hed, attach the OkiLAN 6010e to a printer and po wer cycle the print serv er .
TCP/IP IV - 69 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide • If the ping succeeds, try ftping a test f ile to the print serv er . If the ping fails, you might ha v e a configuration problem with the OkiLAN 6010e (the IP address or gate way address might be incorrect, etc.
IV - 70 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Appendix B: Application Consider - ations Over view This appendix provides application notes for the follo w- ing: • Assigning the OkiLAN 6010e IP Address with BOO TP • Assigning the OkiLAN 6010e IP Address with RARP • Using the W indows NT v3.
TCP/IP IV - 71 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Assigning the OkiLAN 6010e IP Address with BOO TP BOO TP is an acron ym for BOO T Strap P rotocol. Ev ery TCP/IP network de vice is required to ha v e a unique 32- bit IP address assigned to it.
IV - 72 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide IP addresses are 32-bits and are expressed in 4 bytes (decimal format) usually separated by periods. Each decimal byte has a range from 0 to 255. Example: 192.168.42.1 Conf iguration File The purpose of BOO TP is to look up a 32-bit IP address gi ven a 48-bit network hardw are address.
TCP/IP IV - 73 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide The ht signif ies hardware type. For the OkiLAN 6010e, it will always be ether for an Ethernet de vice and token for a T oken-Ring de vice. The ha signif ies the network hardware address.
IV - 74 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide 4. The bootpd daemon transmits a response to the OkiLAN 6010e with the IP address 192.168.42.55. The OkiLAN 6010e will use this IP address for all subsequent transmis- sions. For these ste ps to work properly , at least one BOO TP daemon (bootpd) must be running on the BOO TP serv er .
TCP/IP IV - 75 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide OR • Y our router(s) ar e conf igured to forward BOO TP packets between the OkiLAN 6010e’ s subnet and the subnet of the host running the BOO TP server . Configuring the OkiLAN 6010e IP Ad- dress with RARP RARP is an acronym for R e verse A ddress R esolution P rotocol.
IV - 76 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Address F o rmats Network hardw are addresses are 48-bits and are e x - pressed in 6 bytes in hexadecimal format usually sepa- rated by colons. Each he xadecimal byte has a range from 00 to FF .
TCP/IP IV - 77 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide /etc/ethers: The “/etc/ethers” file is where each entr y maps a host name to a network hardware address. An e xample entr y is sho wn belo w . 00:02:16:17:50:A4 OKIPRINTER The follo wing sequence of e vents occurs during the po w er up of the OkiLAN 6010e using RARP: 1.
IV - 78 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide 5. The rarpd daemon transmits a response to the OkiLAN 6010e with the IP address 192.168.42.55. The OkiLAN 6010e will then use this IP address for all subsequent transmissions. For all these steps to w ork pr operly , at least one RARP daemon (rarpd) must be running on the RARP server .
TCP/IP IV - 79 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Configuring HP-UX v8.07 f or Printing with the OkiLAN 6010e This application note describes the configuration of the printing system on the HP-UX ver . 8.07 of the UNIX operating system.
IV - 80 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Prer equisites Before you proceed, the follo wing prerequisites m ust be met. Most of the time, steps 2 through 5 are already conf igured since the HP-UX system is on a TCP/IP network. Do not perform steps 2 through 5 unless the installation procedure fails! 1.
TCP/IP IV - 81 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide This is helpful if the daemon was terminated for some reason. For more information on inetd or “/etc/inetd.conf”, type man inetd or man inetd.conf . 4. Make sure the follo wing entry is in the “/etc/ services” f ile printer 515/tcp spooler 5.
IV - 82 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide A form appears asking you to def ine a remote printer . 4. Enter information into the following f ields as described. a) Printer name – lj4 This is the name of the printer as refer - enced by the local HP machine.
TCP/IP IV - 83 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide f) Make this the system default printer ? (y or n) – n g) Printer class – (optional) h) Restrict cancel – (optional) i) Remote printer on a BSD system? (y or n) – y T ells the HP-UX system that it is com- municating with a Berkele y style remote printer (such as LPD).
IV - 84 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Configuring HP-UX v9.xx f or Printing with the OkiLAN 6010e This application note describes the configuration of the printing system on the HP-UX ver .
TCP/IP IV - 85 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Prer equisites Before you proceed, the follo wing prerequisites m ust be met. Most of the time steps 2 through 5 are already conf igured since the HP-UX system is on a TCP/IP network.
IV - 86 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide 3. Make sure the follo wing entry is in the “/etc/ inetd.conf” file: printer str eam tcp nowait r oot “/usr/lib/ rlpdaemon” rlpdaemon –i If the rlp daemon is not running when a print request is made, this entry in “/etc/ inetd.
TCP/IP IV - 87 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide 2. In v oke the SAM utility by typing sam at the UNIX prompt. (W e suggest you do this at the system console.
IV - 88 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide This is the name of the queue on the OkiLAN 6010e and must end with 1, 2, 3 or 4, depending on the port selected to service the print jobs. d) Remote cancel model – r cmodel Used for remote printer job remov al.
TCP/IP IV - 89 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide 7. Select the Exit SAM b utton. 8. T est printing to the OkiLAN 6010e with the follo wing command: lp –d lj4 f ilename Configuring HP-UX v10.xx f or Printing with the OkiLAN 6010e This application note describes the configuration of the printing system on the HP-UX ver .
IV - 90 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide If FF , LF or NF are the last two letters of the queue name, the job will be con v erted accordingly . See the section on Remote Queue Names . Prer equisites Before you proceed, the follo wing prerequisites m ust be met.
TCP/IP IV - 91 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide 3. Make sure the follo wing entry is in the “/etc/ inetd.conf” file: printer str eam tcp nowait r oot “/usr/lib/ rlpdaemon” rlpdaemon –i If the rlp daemon is not running when a print request is made, this entry in “/etc/ inetd.
IV - 92 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide 2. In v oke the SAM utility by typing sam at the UNIX prompt. (W e suggest you do this at the system console.
TCP/IP IV - 93 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide c) Remote printer name – y ourqueuename This is the name of the queue on the OkiLAN 6010e and must end with 1, 2, 3 or 4, depending on the port selected to service the print jobs. d) Remote cancel model – r cmodel Used for remote printer job remov al.
IV - 94 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide 6. Pull do wn the Lists menu and select Exit . 7. Select the Exit SAM b utton. 8. T est printing to the OkiLAN 6010e with the follo wing co.
TCP/IP IV - 95 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide • y ourqueuename – This is the name of the queue on the OkiLAN 6010e and must end with 1, 2, 3 or 4 depending on the port selected to service the print jobs. If FF , LF or NF are the last two letters of the queue name, the job will be con v erted accordingly .
IV - 96 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide 3. If remote line printing is already installed, mkdev rlp will respond with the message Remote line printing working dir ectory alr eady e xists. Do you wish to contin ue installing the r emote line printing system? Answer no to this prompt and skip to Step 6.
TCP/IP IV - 97 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide 7. At the UNIX prompt, type: mkdir /usr/ spool/lpd/lj4 8. T ype: touc h/usr/spool/lpd/lj4/lj4.log 9. T ry printing to the OkiLAN 6010e by issuing the follo wing command: lp –d lj4 f ilename IBM’ s AIX ver .
IV - 98 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide • y our queuename – This is the name of the queue on the OkiLAN 6010e and must end with 1 or 2, depending on the port selected to service the print jobs. If FF , LF or NF are the last two letters of the queue name, the job will be con v erted accordingly .
TCP/IP IV - 99 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide A form appears asking you to def ine a remote print queue. 4. Enter information into the following f ields as described. All other fields should use the default v alue. a) N AME of queue to add – lj4 This is the name of the local print queue.
IV - 100 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide 5. Start the lpd subsystem with SMIT : Spooler (Print Jobs and Printers) Manage Remote Printer Subsystem Server Services lpd Remote Printer Subsystem Start Using the lpd Subsystem Start BO TH No w and at System Restart 6.
TCP/IP IV - 101 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide • OKIPRINTER – The host name of the r emote system w hich is the OkiLAN 6010e. For e xample, to telnet to the OkiLAN 6010e and in voke the OkiLAN 6010e Conf igura- tion utility , you would type telnet OKIPRINTER .
IV - 102 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Procedur e T o configure the Solaris machine so users can spool print jobs to the pcl print queue on the OkiLAN 6010e named OKIPRINTER, do the follo wing: 1. Login to the Solaris machine as root.
TCP/IP IV - 103 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide • OKIPRINTER – The host name of the r emote system w hich is the OkiLAN 6010e. For e xample, to telnet to the OkiLAN 6010e and in voke the OkiLAN 6010e Conf igura- tion utility , you would type telnet OKIPRINTER .
IV - 104 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide 2. Make sure the LPD daemon is running on the Sun-OS or Ultrix system by issuing the follo wing command at the UNIX prompt: ps aux | grep lpd If the LPD daemon is running, you should see output similar to: root 135 0.
TCP/IP IV - 105 Section IV - TCP/IP OKI OkiLAN 6010e User’ s Guide Procedur e T o conf igure the Sun-OS or Ultrix machine so that users can spool print jobs to the pcl print queue on the OkiLAN 6010e named OKIPRINTER , do the follo w- ing: 1. Login to the Sun-OS or Ultrix machine as root.
.
Windo ws Printing Section V : Windo ws Printing.
.
Windo ws Printing V - 3 Section V - W indows Printing OKI OkiLAN 6010e User’ s Guide In This Section Chapter 1: OkiLAN 6010e Set Up f or Windo ws NT 4.0 .............................. V -5 Overvie w ..................................................
V - 4 Section V - W indows Printing OKI OkiLAN 6010e User’ s Guide.
Windo ws Printing V - 5 Section V - W indows Printing OKI OkiLAN 6010e User’ s Guide Chapter 1: OkiLAN 6010e Set Up f or Windo ws NT 4.0 Over view This section contains instruction and information on ho w to set up your OkiLAN 6010e for a W indo ws NT 4.
V - 6 Section V - W indows Printing OKI OkiLAN 6010e User’ s Guide Installation T o install OkiLAN 6010e Connect for TCP/IP , follo w the instructions belo w: 1. Install the OkiLAN 6010e Connect for TCP/ IP f iles – see Section I. 2. When installation is complete, click on Start , Settings and then Printers .
Windo ws Printing V - 7 Section V - W indows Printing OKI OkiLAN 6010e User’ s Guide 5. From the list of A vailable Printer P orts , select OKI OkiLAN 6010e Connect IP Monitor as the type of port to add and click New P ort .
V - 8 Section V - W indows Printing OKI OkiLAN 6010e User’ s Guide Y ou will enter into the Add OkiLAN 6010e Connect P ort screen where there will be a list of all OkiLAN 6010e print servers av ailable on the local subnet.
Windo ws Printing V - 9 Section V - W indows Printing OKI OkiLAN 6010e User’ s Guide 6. If the port you wish to add is listed in the P orts available on local subnet: windo w , select the port name and click Add .
V - 10 Section V - W indows Printing OKI OkiLAN 6010e User’ s Guide OkiLAN 6010e Connect f or DLC OkiLAN 6010e Connect for Data-Link Control (DLC) provides a direct printing solution for user s in Microsoft W indows NT ser v e rless en vironments with the DLC/ LLC protocol.
Windo ws Printing V - 11 Section V - W indows Printing OKI OkiLAN 6010e User’ s Guide Description An optional f ield where you may list the location or other useful information about the printer port. Using the Windows NT 4.0 LPR Print Monitor A Microsoft LPR print monitor is shipped with W in- do ws NT 4.
V - 12 Section V - W indows Printing OKI OkiLAN 6010e User’ s Guide Install LPR Print Monitor 1. Open the W indo ws NT Control P anel . 2. Select the Services tab . 3. Select Add , then Micr osoft TCP/IP print- ing . 4. Click the Close b utton. 5. Restart the system.
Windo ws Printing V - 13 Section V - W indows Printing OKI OkiLAN 6010e User’ s Guide 5. In the Name or addr ess of server pr oviding lpd: f ield, enter the IP address you assigned to the printer . 6. In the Name of printer or print queue on that server: f ield, enter the print server output port being used.
V - 14 Section V - W indows Printing OKI OkiLAN 6010e User’ s Guide 7. Click OK . 8. V erify the port just added is selected and then click Next . 9.
Windo ws Printing V - 15 Section V - W indows Printing OKI OkiLAN 6010e User’ s Guide Chapter 2: OkiLAN 6010e Set Up f or Windo ws NT 3.51 Over view This section contains instruction and information on ho w to set up your OkiLAN 6010e for a W indo ws NT 3.
V - 16 Section V - W indows Printing OKI OkiLAN 6010e User’ s Guide Installation T o install OkiLAN 6010e Connect for TCP/IP , follo w the instructions belo w: 1. Install the OkiLAN 6010e Connect for TCP/ IP f iles—see Section I. 2. From the W indows NT Print Manage r Printer menu select Cr eate Printer .
Windo ws Printing V - 17 Section V - W indows Printing OKI OkiLAN 6010e User’ s Guide OkiLAN 6010e Connect f or DLC OkiLAN 6010e Connect for Data-Link Control (DLC) provides a direct printing solution for user s in Microsoft W indows NT ser v e rless en vironments with the DLC/ LLC protocol.
V - 18 Section V - W indows Printing OKI OkiLAN 6010e User’ s Guide Install TCP/IP and LPR Print Monitor T o install the LPR print monitor on your system, follo w the steps belo w: 1. Open the W indo ws NT Control P anel . 2. Double-click the Network icon.
Windo ws Printing V - 19 Section V - W indows Printing OKI OkiLAN 6010e User’ s Guide Assign Print Server IP Addr ess 1. Using OkiNet f or IP , assign the print server an IP address; for e xample, 10.10.10.2. Note: For mor e information on using OkiLAN 6010e TCP/IP , see OkiNet for TCP/IP .
V - 20 Section V - W indows Printing OKI OkiLAN 6010e User’ s Guide Chapter 3: OkiLAN 6010e Set Up f or Windo ws 95 Over view This section contains instruction and information on ho w to set up y our OkiLAN 6010e f or a W indows 95 en vir onment.
Windo ws Printing V - 21 Section V - W indows Printing OKI OkiLAN 6010e User’ s Guide Installation T o install OkiLAN 6010e Connect for TCP/IP , follo w the instructions belo w: 1. Install the OkiLAN 6010e Connect for TCP/ IP—see Section I. 2. When installation is complete, click on Start , Settings and then Printers .
V - 22 Section V - W indows Printing OKI OkiLAN 6010e User’ s Guide Y ou will enter into the Add OkiLAN 6010e Connect P ort screen where there will be a list of all OkiLAN 6010e print servers av ailable on the local subnet.
Windo ws Printing V - 23 Section V - W indows Printing OKI OkiLAN 6010e User’ s Guide 6. If the port you wish to add is listed in the P orts available on local subnet windo w , select the port name and click the Add b utton.
V - 24 Section V - W indows Printing OKI OkiLAN 6010e User’ s Guide OkiLAN 6010e Connect f or DLC OkiLAN 6010e Connect for Data-Link Control (DLC) provides a direct printing solution for user s in Microsoft W indows 95 serv erless en vir onments with the DLC/ LLC protocol.
Windo ws Printing V - 25 Section V - W indows Printing OKI OkiLAN 6010e User’ s Guide 5. In the Add P ort windo w , select the radio b utton labeled Other and select OKI OkiLAN 6010e Connect DLC Monitor as the type of port to add.
V - 26 Section V - W indows Printing OKI OkiLAN 6010e User’ s Guide Y ou will now be able to use OkiLAN 6010e Connect for DLC. Whene ver you print to the printer conf igur ed with OkiLAN 6010e Connect, your print job will go directly to the OkiLAN 6010e print server port.
Index-1 Index OKI OkiLAN 6010e User’ s Guide Index A Advanced Management Features OkiNet Alert II-26 OkiNet for NDS II-27 OkiNet for TCP/IP II-27 printer security for TCP/IP II-28 Security II-7 Assi.
Index-2 Index OKI OkiLAN 6010e User’ s Guide Custom V iews II-27 Customer Information Center vii Customer Service Representatives vii Customer Support Center vii Customized V iews creating in OkiNet.
Index-3 Index OKI OkiLAN 6010e User’ s Guide STRU IV-24 TYPE IV-24 G GET Community Name (TCP/IP) IV-39 Gleaning assigning an IP address IV-1 1 H HP-UX v10.xx Application prerequisites IV-90 procedure IV-91 HP-UX v8.07 Application prerequisites IV-80 procedure IV-81 HP-UX v9.
Index-4 Index OKI OkiLAN 6010e User’ s Guide L Language Switching NetW are III-14 N NDS Settings in NetW are III-1 1 NPrinter Mode in NetW are III-6 O OkiLAN 6010e Diagnostic Information displaying .
Index-5 Index OKI OkiLAN 6010e User’ s Guide Output Port Configuration Options in TCP/IP IV-34 Output port configuration options in NetW are III-13 P Port Configuration in NetW are III-12 Print Queu.
Index-6 Index OKI OkiLAN 6010e User’ s Guide RPrinter Mode in NetW are III-6, III-1 1 S SCO UNIX Application prerequisites IV-95 procedure IV-95 Security in SNMP II-7 Service and Support Customer In.
Index-7 Index OKI OkiLAN 6010e User’ s Guide requirements V-5, V-15 restoring to factory default configuration IV-61 static route entry IV-64 unable to assign IP address IV-62 UNIX BOOTP IV-63 W ins.
Index-8 Index OKI OkiLAN 6010e User’ s Guide V V erifying Access to the OkiLAN 6010e IV-16 V iew Settings modifying in OkiNet for TCP/IP IV-46 V iew settings modifying in NetW are III-24 W W eb Conf.
An important point after buying a device Oki POCKET PRINT 6010E (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Oki POCKET PRINT 6010E yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Oki POCKET PRINT 6010E - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Oki POCKET PRINT 6010E you will learn all the available features of the product, as well as information on its operation. The information that you get Oki POCKET PRINT 6010E will certainly help you make a decision on the purchase.
If you already are a holder of Oki POCKET PRINT 6010E, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Oki POCKET PRINT 6010E.
However, one of the most important roles played by the user manual is to help in solving problems with Oki POCKET PRINT 6010E. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Oki POCKET PRINT 6010E along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
