Instruction/ maintenance manual of the product 8814R NuTone
Go to page of 10
INST ALLA TION INSTRUCTIONS READ & SA VE THESE INSTRUCTIONS! ® IMPORT ANT SAFETY INSTRUCTIONS WARNING: TO REDUCE THE RISK OF FIRE. ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: A. Use this unit only in the manner intended by the manufacturer.
INST ALLA TION IN A NEW CONSTRUCTION SITE PREP ARA TION Refer to Figure 1. 1. To remove blower/power unit assembly from housing: A. Unplug power unit. B. Remove screw (located next to plug-in receptacle) which holds blower/power unit mounting plate in place.
INST ALLA TION IN EXISTING CONSTRUCTION Note: Installation in a finished house requires an accessible area (attic or crawl space) above the planned installation location. 1. After determining desired location for fan, drill a small hole in the ceiling.
INSTRUCTIONS D'INST ALLA TION LIRE ET CONSERVER CES INSTRUCTIONS ® IMPORT ANTES DIRECTIVES DE SÉCURITÉ AVERTISSEMENT: POUR RÉDUIRE LES RISQUES D’INCENDIE, DE CHOCS ÉLECTRIQUES OU DE BLESSURES, RESPECTER CE QUI SUIT : A. Utiliser cet appareil seulement pour les fins prévues par le fabricant.
INST ALLA TION DANS UNE CONSTRUCTION NEUVE PREPARATION 1. Voir Figure 1 . Enlever le bloc-moteur du boîtier. A. Débrancher le moteur. B. Enlever et conserver la vis (placée près de la prise de branchement) qui retient la plaque de montage du moteur en place.
FIGURE 5 RESSORTS DE MONTAGE INSERRER LES PATTES DANS LES FENTES GRILLE Les caractéristiques peuvent être modifiées sans préavis 4820 Red Bank Road, Cincinnati, Ohio 45227 Imprimé aux E.
INSTRUCCIONES DE INST ALACION ¡LEA Y GUARDE EST AS INSTRUCCIONES! ® INSTRUCCIONES IMPORT ANTES DE SEGURIDAD ADVERTENCIA: PARA REDUCIR EL RIESGO DE INCENDIO, CHOQUE ELECTRICO O LESIONES A LAS PERSONAS, OBSERVE LO SIGUIENTE: A. Utilice esta unidad solamente de la manera planeada por el fabricante.
INST ALACION EN UN NUEVO EDIFICIO EN CONSTRUCCION PREP ARACION Vea la Figura 1. 1. Para remover del bastidor el ensamblaje de la unidad de poder/soplador: A. Desenchufe la unidad de poder. B. Remueva el tornillo (localizado al lado del receptáculo de enchufe) que sujeta en su lugar el plato de montaje de la unidad de poder/soplador.
INST ALACION DE LA UNIDAD DE PODER/SOPLADOR 1. Coloque la unidad de poder/soplador dentro del bastidor de manera que las orejas del plato de montaje se inserten en las ranuras del bastidor. 2. Presione el otro extremo del plato de montaje hacia abajo hasta que se asiente firmemente sobre el resguarde circular y los receptáculos de enchufe.
8814R Rev. SEPTEMBER 1999 CURRENT ORIGINAL REPLACEMENT REF. PART NO. PART DESCRIPTION PART NO. 1 86863 MOTOR MOUNTING PLATE 86863-000 2 32787 MOTOR ISOLATION MOUNT 32787-000 3 32788 GROUND CLIP 32788-.
An important point after buying a device NuTone 8814R (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought NuTone 8814R yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data NuTone 8814R - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, NuTone 8814R you will learn all the available features of the product, as well as information on its operation. The information that you get NuTone 8814R will certainly help you make a decision on the purchase.
If you already are a holder of NuTone 8814R, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime NuTone 8814R.
However, one of the most important roles played by the user manual is to help in solving problems with NuTone 8814R. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device NuTone 8814R along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
