Instruction/ maintenance manual of the product SA5500 Numark Industries
Go to page of 16
Owner’s Manual SA3000/SA5500/SA9500 Amplifiers.
©1997 Numark Industries http://www.numark.com 2.
©1997 Numark Industries http://www.numark.com 3 SAFETY FIRST! WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
©1997 Numark Industries http://www.numark.com 4.
©1997 Numark Industries http://www.numark.com 5 Contents Warning and Safety Instructions 3 Introduction 6 Front-Panel Description 7 Back-Panel Description 8 Audio Terms 10 Hook-up #1: Home Studio Ref.
©1997 Numark Industries http://www.numark.com 6 Introduction Thank you for choosing a Performance Series power amplifier from Numark. These units are designed to provide a good combination of power, audio clarity, and reliable operation.
©1997 Numark Industries http://www.numark.com 7 Front Panel Description 1. Gain Controls These two knobs are the level controls for each channel of the amplifier. The gain increases as the knob is turned clockwise. The SA5500 features detented gain controls with dB calibrations to simplify set up.
©1997 Numark Industries http://www.numark.com 8 Back Panel Description 6. Neutrick Connector Inputs a. Balanced XLR Inputs These combined inputs are commonly used for both mobile and installation set ups. The XLR provide a good combination of ease of connection and resistance to corrosion.
©1997 Numark Industries http://www.numark.com 9 3. ensure that there is only one input signal connected to channel 1 of the amplifier - channel 2 input must be vacant 4. switch the amplifier to bridged mono (back panel switch) 5. turn the gain down and turn on the amp 6.
©1997 Numark Industries http://www.numark.com 10 Audio Terms Gain This is the factor by which an input signal is amplified (increased) or attenuated (reduced) when passing through an amplifier. Gain is generally measured in decibels (dB) which is a logarithmic ratio of input to output.
©1997 Numark Industries http://www.numark.com 11 The variable resistor is to ensure an impedance balance between the positive and negative inputs, and should be adjusted until any hum is at a minimum. Balanced lines are also the most effective means of reducing or eliminating RF or ‘radio frequency interference’.
©1997 Numark Industries http://www.numark.com 12 Hook up #1 Home Studio Reference Amplifier outputs AMPLIFIER OUTPUTS + - AMPLIFIER INPUTS + - - + GND CH-2 CH-1 CH-2 CH-1 reference monitors Numark am.
©1997 Numark Industries http://www.numark.com 13 Hook up #3 Monitor Amplifier (in bridged mono) Zone/Booth send AMPLIFIER OUTPUTS + - AMPLIFIER INPUTS + - - + GND CH-2 CH-1 CH-2 CH-1 monitor speaker .
©1997 Numark Industries http://www.numark.com 14 Specifications SA9500 SA5500 SA3000 Frequency response (8 ohms , 20Hz - 20kHz @ 1 W) +0, -1dB +0, -1dB +0, -1dB Total harmonic distortion 0.
©1997 Numark Industries http://www.numark.com 15 Block Diagrams ch2 outputs ch1 outputs detector short circuit protection detector clip/limit short circuit protection + - + - + - + - + - + - + - + - .
©1997 Numark Industries http://www.numark.com 16 Professional Disc Jockey Products LIMITED WARRANTY Numark Industries, LLC and Numark International, Inc.
An important point after buying a device Numark Industries SA5500 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Numark Industries SA5500 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Numark Industries SA5500 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Numark Industries SA5500 you will learn all the available features of the product, as well as information on its operation. The information that you get Numark Industries SA5500 will certainly help you make a decision on the purchase.
If you already are a holder of Numark Industries SA5500, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Numark Industries SA5500.
However, one of the most important roles played by the user manual is to help in solving problems with Numark Industries SA5500. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Numark Industries SA5500 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
