Instruction/ maintenance manual of the product GLX20 ACCO Brands
Go to page of 13
SERVICE MANU AL (2008.12.18) MODELS: GBC GLS28, GLX20, GLM11, GLHS9 REXEL RLS28, RLX20, RLM11, RLSM9.
© 2008 All Rights Reserved No part of this publication may be reproduced in any form without expressed written permission from Electronically Printed a n d Designed in the USA.
2 8-9 INTRODUCTION TROUBLESHOOTING DISASSEMBL Y/ADJUSTMENTS MAINTENANCE 10.0 SPECIAL INSTRUCTIONS INST ALLA TION T able of Contents 1 SPECIFICATIONS 3-7.
Introduction 1 Introduction 1 Illuminated Panel 1 2 3 4 a d e f b c g a d e f b c g Models: GBC GLS28, GLX20 / REXEL RLS28, RLX20 Models: GBC GLM11, GLHS9 / REXEL RLM11, RLSM9 a Indicator Panel b Door.
2 Specifications Specications GLS28 28 sheets Continuous operation 120V AC / 60Hz 8.0 A Models Sheet Capacity - Duty Cycle - V olts / Hz Amperage GLX20 20 sheets Continuous operation 120V AC / 60Hz 10.0 A GLM11 11 sheets Continuous operation 120V AC / 60Hz 10.
Mechanical Operation The shredder uses two rotating cutting shafts, which are driven by an electrical motor to shred paper . Electrical Operation When the ce n te r p o we r o n switch is pressed, al .
5.0 T General T roubleshooting Malfunction corrections are based on visual obser- vations made by the operator . The causes of the malfunctions are isolated by the symptom of the malfunction and noting at which point in the operat- ing cycle the malfunction occurred.
5.0 Shredder Does Not Operate, No Indication Of Power Shredder Does Not Operate, With Indication Of Power Present Shredder Does Not Operate, (When Paper Is Present In The Throat) Shredder Runs Continuously Sheet Cap acity Diminished Power Cord Disconnected.
6 T roubleshooting Main Board panel board Power SW Paper Trigger Emitter Paper Trigger receiver CD Detection sensor Bin Full detection PCB box Binfull Trigger Photo sensor(#5) 1 2 BIN2A1 2P/2.
T roubleshooting 7 1 5V SW 5V SW 2 5V 5VSW 5V 5VSW 5V SW 5V SW 5VSW 5V SW 5VSW TC0 Forward Reverse Line SW TCO Power OUT Power IN Forward Reverse Line SW Line SW door Open NEUTRAL Timmer NEUTRAL NEUTR.
Necessary T ools 1. 2. #2 Phillips Screwdriver Disassembly of the shredder is described in the following steps. Top Housing Removal W ARNING! Disconnect the unit from the receptacle before performing any disassembly procedures. 1.Unplug the power cord from the outlet power supply .
Gear Box Removal 1 . Remove the s i x phillips screws from the gear box cover . 2. Remove the two 14mm bolts. 3. Remove the two phillips screws from the encoder housing. 4. Remove gearbox cover. Motor Removal 1. Remove large double drive gear. 2. Remove small double drive gear.
12/18/08 F ull Circle Ser vice TM 10303 80th A venue Pleasant Pr aire, Wi 53158.
An important point after buying a device ACCO Brands GLX20 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ACCO Brands GLX20 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ACCO Brands GLX20 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ACCO Brands GLX20 you will learn all the available features of the product, as well as information on its operation. The information that you get ACCO Brands GLX20 will certainly help you make a decision on the purchase.
If you already are a holder of ACCO Brands GLX20, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ACCO Brands GLX20.
However, one of the most important roles played by the user manual is to help in solving problems with ACCO Brands GLX20. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ACCO Brands GLX20 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
