Instruction/ maintenance manual of the product NETGEAR
Go to page of 400
202-10088-01, Ma rch 2005 202-10088-01 March 2005 NETGEAR , Inc. 4500 Great America Parkway Santa Clara, CA User Manual for the NETGEAR 7300S Series Layer 3 Managed Switch Sof tware.
ii 202-10088-01, Ma rch 2005 © 2005 by NETGEAR, Inc., March 2005. FullManual All rights reserved. T echnical Support Please register to obtain technical support .
202-10088-01, Ma rch 2005 iii Canadian Dep artment of Commu nications Compliance St atement This Class B Digital apparatus (NETGEAR 7300S Series Layer 3 Managed Switch) meets all the requirements of the Canadian Interfe rence Causing Equipment Regulations.
202-10088-01, March 20 05 iv.
Contents v 202-10088-01, March 2005 Content s Chapter 1 About This Guide Audience ............. ................ ................ ................ ................ ................ ................ ......... ... 1-1 Why the Document was Created ......
202-10088-01, March 200 5 vi Contents Chapter 5 Command Li ne Interf ace Structure CLI Command Format ........... ................ ................ ................ ................. ................ ........ 5-1 Command .............. ... .... ... ..
Contents vii 202-10088-01, March 2005 show logging ............ ................. ............. ................ ................ ................ ................ 8-13 show mac-addr-table .... ................ ................ ................ ......
202-10088-01, March 200 5 viii Contents set prompt ............. ................ ............. ................ ................. ................ ................ ... 8-23 serviceport ip ................ ... ... ... .... ... ............. ... ... ..
Contents ix 202-10088-01, March 2005 snmptrap ipaddr ........... ................ ................ ................ ................ ................ .......... 8-34 snmptrap mode .................. ............. ............. ................ .......
202-10088-01, March 200 5 x Contents speed .............. ................ ................ ................ ................ ............. ................ .......... 8-42 speed all ................ ................ ................. ................
Contents xi 202-10088-01, March 2005 vlan protocol group add protocol ............ ...... ............. ................ ................ ............. 8-53 no vlan protocol group add protocol ................ ................ ................... ....
202-10088-01, March 200 5 xii Contents Configuration Scripting ....................... ... ... .... ... ................ ................ ................ ... .......... 8-64 configscript apply ............... ... .... ... ... ... ............. ... ..
Contents xiii 202-10088-01, March 2005 sntp unicast client poll-timeout ............... ... ................ ................ ................ ............. 8-74 no sntp unicast client poll-timeout ............... .... ... ... ... .... ... ... ... ...
202-10088-01, March 200 5 xiv Contents no hardware-address ... .................... ................ ................ ................ ................ 8-84 host .......... ............. ................ ................. ................ ............
Contents xv 202-10088-01, March 2005 show ip dhcp conflict .................... ............. ... ............. ................ ................ ............. 8-93 clear ip dhcp binding ............. ................. ................ ...............
202-10088-01, March 200 5 xvi Contents no set gmrp interfacemode . ................ ................ ................ ................ ........... 8-103 set gmrp interfacemode all . ............. ............. ................ ................ .......
Contents xvii 202-10088-01, March 2005 port lacpmode .... ................ .................... ................ ................ ................ .............. 8-1 14 no port lacpmode ......... ................ ................ ................. ...
202-10088-01, March 200 5 xviii Contents no spanning-tree mst instance .................. ................ ................. ................ .... 8-124 spanning-tree mst priority ... ............. ................ ................ ................. .
Contents xix 202-10088-01, March 2005 no port-security max-dynamic ............ ................ ................ ................ ............... 9-2 port-security max-static ................... ................ ................ ................. ...
202-10088-01, March 200 5 xx Contents no dot1x user ............... ................ ................ ................. ................ ................ ... 9-1 1 show radius accounting ............. ................ ................ ................
Contents xxi 202-10088-01, March 2005 no ip http server ........ ................ ................ ................ ................. ................ ...... 9-25 show ip http ..................... ................ ................ ................ ..
202-10088-01, March 200 5 xxii Contents no ip route distance ............... ................ ................ ................ ................ .......... 10-9 ip forwarding .......... ... .... ... ............. ... ... .... ... ... ... ... .... ... .
Contents xxiii 202-10088-01, March 2005 ip irdp maxadvertinterval .... ... .... ... ... ... .... ............ ................. ................ ............. .... 10-19 no ip irdp maxadvertinterval ................ ......... ................. .......
202-10088-01, March 200 5 xxiv Contents split-horizon .............. ................. ................ ................ ................ ................ ........... 1 0-27 no split-horizon ............ ................ ................ .............
Contents xxv 202-10088-01, March 2005 match destination-address mac ... .... ... ... ... ............. ............. ................ ........... 1 1-13 match dstip ............... ... ... .... ... ... ... ............. ... .... ... ... ... .... ... .
202-10088-01, March 200 5 xxvi Contents Show Commands .................. .... ... ... ... .... ... ... ... ... .... ... ... ................ ................ ........ 1 1-30 show class-map ........... ................ ................ ................
Contents xxvii 202-10088-01, March 2005 show interfaces tail-drop-threshold . ................ ................ ................. ................ .... 1 1-48 Chapter 12 Managing Switch St acks Understanding Switch S tacks ................ ...........
202-10088-01, March 200 5 xxviii Contents Appendix A IS CLI Mapping Appendix B Cabling Guidel ines Fast Ethernet Cable Guidelin es ............. ................... .................... ................... .............. B-1 Category 5 Cable .........
Contents xxix 202-10088-01, March 2005 T ............... ................ ............. ................ ................ ................ ................. ................ ..... C-19 U ............... ............. ................ ................ .
202-10088-01, March 200 5 xxx Contents.
About This Guide 1-1 202-10088-01, March 2005 Chapter 1 About This Guide Thank you for pu rchasing the NETGEAR ™ 7300S S eries L3 Switch. Audience This reference manual assumes that the reader h as basic-to-intermediate computer and Internet skills.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 1-2 About This Guide 202-10088-01, March 2005 • Chapter 10, “Rout ing Commands” describes the Routing commands . • Chapter 1 1, “Quality of Service (QoS) Commands” des cribes the QOS commands.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software About This Guide 1-3 202-10088-01, March 2005 Note: Product updates are available on the NETGEAR, Inc.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 1-4 About This Guide 202-10088-01, March 2005.
Switch Management Overview 2-1 202-10088-01, March 2005 Chapter 2 Switch Management Overview This chapter gives an overview of switch ma nagement, including the method s you can use to manage your NETG EAR 7300S Series Layer 3 Manage d Switch .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 2-2 Switch M anageme nt Overview 202-10088-01, March 2005 • Simple Network Protocol Managemen t (SNMP) Each management metho.
Administration Console Interface 3-1 202-10088-01, March 2005 Chapter 3 Administration Console Interface The administration console is an internal, charac ter-oriented, VT -100/ANSI command-driven user interface for performing management activities.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 3-2 Administration Console Interface 202-10088-01, March 2005 Examples o f terminal-emu lation programs include: • HyperT er.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Administration Console Interface 3-3 202-10088-01, March 2005 4. When the following screen appe ars, make sure that the port setting are as follows: Baud Rate: 9600 Data Bits: 8 Parity: None Stop Bits: 1 Flow Control: None Figure 3-4: Connectio n Settings 5.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 3-4 Administration Console Interface 202-10088-01, March 2005.
Web-Based Manage men t Interface 4-1 202-10088-01, March 2005 Chapter 4 W eb-Based Management Interface Y our NETGEAR 7300S Series Layer 3 Managed Switc h provides a built-in browser interface that lets you configure and man age it remotely using a standard W eb browser such as Microsoft Internet Explorer 5.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 4-2 We b-Based M anagement Interface 202-10088-01, March 2005 W eb Based Management Overview The menu options available are: System Manage ment, Switch, Routing, Traf fic Management, and Smart W izard.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Web-Based M anagement Interface 4-3 202-10088-01, March 2005 A login window opens: Figure 4-3: Login splash scr een for the Managed Switch Click the Login link. A user name and password dial og box opens like this one.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 4-4 We b-Based M anagement Interface 202-10088-01, March 2005 Once you have entered your user name and passw ord, your W eb browser should automatically retrieve and display the ho me page, as shown below .
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Web-Based M anagement Interface 4-5 202-10088-01, March 2005 Interactive Switch Image Figure 4-6: Interactive switch imag e T.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 4-6 We b-Based M anagement Interface 202-10088-01, March 2005 Menus The W eb-based interface enables navigation throug h several menus.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Web-Based M anagement Interface 4-7 202-10088-01, March 2005 Secondary Menus The Secondary Menus under the Main Menu contain a host of options that yo u can use to configure your switch.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 4-8 We b-Based M anagement Interface 202-10088-01, March 2005 Routing • Routing Commands — see “Routing Command s” on .
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Web-Based M anagement Interface 4-9 202-10088-01, March 2005 Port-S pecific Popup Menus The 7300S Series L3 Switch also pr ovides several popup menus for each port.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 4-10 Web-Based M anagement Interface 202-10088-01, March 2005.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Command Line Interface Stru cture 5-1 202-10088-01, March 2005 Chapter 5 Command Line Interface S tructure The Command Line Interface (CLI) syn t ax , conventions and terminology are described in this section.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 5-2 Command Line Inter face Structure 202-10088-01, March 2005 Parameters Parameters are order dependent.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Command Line Interface Stru cture 5-3 202-10088-01, March 2005 logical slot/port This parameter denote s a logical slot number and logical port number assigned. This is applicable in the case of a port-channel (LAG).
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 5-4 Command Line Inter face Structure 202-10088-01, March 2005 Annot ations The CLI allows the user to type single-line annotations at th e command prompt for use when writing test or configuration scripts and for bette r readability .
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Quick Start up 6-1 202-10088-01, March 2005 Chapter 6 Quick S t art up The CLI Quick S tart up details procedures to quickl y become acquainted with the 7300S Series L3 Switch.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 6-2 Quick Start up 202-10088-01, March 2005 System Info and System Setup Quick S t art up Sof twa re V ersion Information Quick S t art up Physical Port Dat a T able 6-1.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Quick Start up 6-3 202-10088-01, March 2005 Quick S t art up User Account Mana gement Quick S t art up IP Address T o view the network parameters the operator can access the device by the following three methods.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 6-4 Quick Start up 202-10088-01, March 2005 Note: The user should do a copy system:running-config nvram:startup-config after configuring the network parameters so that the configurations are not lost.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Quick Start up 6-5 202-10088-01, March 2005 Quick S t art up Uploading from Sw itch to Out-of-Band PC (Only XMODEM) Quick S t art up Downloading from Out-of-Band PC to Switch (Only XMODEM) T able 6-5.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 6-6 Quick Start up 202-10088-01, March 2005 Quick S t art up Download ing from TFTP Se rver Before starting a TFTP server down load, the operator must complete the Quick Start up for the IP Address.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Mode-based CLI 7-1 202-10088-01, March 2005 Chapter 7 Mode-based CLI The CLI groups all the commands in appropriate modes according to the nature of the comma nd. A sample of the CLI command mode s are described below .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 7-2 Mode-based CLI 202-10088-01, March 2005 VLAN Mode From the Privileged User Exec mode, enter the vlan database command. Switch (Vlan) # T o exit to the Privileged Exec mode, enter the exit command, or press Ctrl-Z to switch to user exec mode.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Mode-based CLI 7-3 202-10088-01, March 2005 Mode-based T opology The CLI tree is built on a mode concept where the commands are availa ble according to the interface. Some of the modes are depict ed in the mode-based CLI Figure 1.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 7-4 Mode-based CLI 202-10088-01, March 2005 Access to all commands in the Privileged Exec mo de and below are restricted through a password. Mode-based Command Hierarchy The CLI is divided into variou s modes.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Mode-based CLI 7-5 202-10088-01, March 2005 In this mode, a physical port is set up for a specific logical con- nection operation. The Interface Config mo de provi des access to the router interface configur ation commands .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 7-6 Mode-based CLI 202-10088-01, March 2005 Flow of Operation This section captures the flow of operation for the CLI: 1. The operator logs into the CLI session and ente rs the User Exec mode.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Mode-based CLI 7-7 202-10088-01, March 2005 “No” Form of a Command "No" is a specific form of an existing command and does not represent a new or distinct command.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 7-8 Mode-based CLI 202-10088-01, March 2005.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-1 202-10088-01, March 2005 Chapter 8 Switching Commands This chapter provides detailed explanation of the Switching commands.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-2 Switching Commands 202-10088-01, March 2005 show arp switch This command displays connec tivity between the switch and other devices. The Addre ss Resolution Protocol (ARP) cache identifies the MA C addresses of the IP st ations communicating with the switch.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-3 202-10088-01, March 2005 Machine T ype Specifies the machine mod el as defined by the V ital Product Data. Machine Model Specifies the machine mod el as defined by the V ital Product Data.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-4 Switching Commands 202-10088-01, March 2005 T ransmit Packet s Errors The number of outbound packets that could not be transmitted because of errors. Collisions Frames The best estimate of the total num ber of collisions on this Ether- net segment.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-5 202-10088-01, March 2005 Format show interface ethernet {< slot/port > | switchport } Mode Privi.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-6 Switching Commands 202-10088-01, March 2005 1518 octets in length inclusive (excluding framing bits but including FCS octets).
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-7 202-10088-01, March 2005 Alignment Errors - The total number of packets received that had a length (ex.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-8 Switching Commands 202-10088-01, March 2005 CFI Discards - The number of frames discarded that have CFI bit set and the addresses in RIF are in non-canonical format.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-9 202-10088-01, March 2005 and 1522 octets in length incl usive (excluding framing bits but including FCS octets). Max Info - The maximum size of the Info (non-MAC) field that this port will receive or transmit.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-10 Switching Comm a nd s 202-10088-01, March 2005 Multiple Collision Frames - A count of the number of success- fully transmitted frames on a particular interface for which trans- mission is inhibited by more than one collision.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-1 1 202-10088-01, March 2005 RST BPDUs T ransmitted - Rapid Spann ing T ree Protocol Bridge Protocol Dat.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-12 Switching Comm a nd s 202-10088-01, March 2005 Octets T ransmitted - The total number of octets transmitted out of the interface, including framing characters. Packets T ransmitted without Errors - The total number o f packets transmitted out of the interface.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-1 3 202-10088-01, March 2005 show logging This command displays the trap lo g maintained by the sw itch. The trap log contains a maximum of 256 entries that wrap.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-14 Switching Comm a nd s 202-10088-01, March 2005 St atic The value of the corresponding in stanc e was added by the system or a user when a static MAC filter was defined. It cannot be relearned.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-1 5 202-10088-01, March 2005 Mode Privileged EXEC show sysinfo This command displays switch information. Format show sysinfo Mode Privileged EXEC Switch Description T ext used to identify this switch.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-16 Switching Comm a nd s 202-10088-01, March 2005 • Show commands display switch settings, statistics, and ot her information. • Configuration commands configure featur es and options of the switch.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-1 7 202-10088-01, March 2005 transport output telnet This command regulates new outbou nd telnet connections.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-18 Switching Comm a nd s 202-10088-01, March 2005 Default 0 Format sessio n-timeout <0-160> Mode Line Config no session-timeout This command sets the outbound telnet session timeout value to the default.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-1 9 202-10088-01, March 2005 mtu This command sets the maximum transmission unit (MTU) size (in bytes) for physical and port- channel (LAG) interfaces. For th e standard implementation, the range of <mtusize> is a valid integer between 1522-9216.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-20 Switching Comm a nd s 202-10088-01, March 2005 • Bit 6 of byte 0 (called the U/L bit) indicates whether the address is universally administered (b'0') or locally administered (b'1').
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-2 1 202-10088-01, March 2005 network protocol This command specifies the networ k configuration pro tocol to be used. If you mod ify this value change is effective immediately .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-22 Switching Comm a nd s 202-10088-01, March 2005 no telnetcon timeout This command sets the telnet co nnection session timeout value, in minutes, to the default. Note: Changing the timeout value for active sessions does not become effective until the session is reaccessed.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-2 3 202-10088-01, March 2005 Mode Line Config set prompt This command ch anges the name of the prompt. The length of n ame may be up to 64 alphanumer ic characters.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-24 Switching Comm a nd s 202-10088-01, March 2005 Allow New Outbound T elnet Sessions Indicates whether outbound telnet sessions will be allowed. show forwarding db agetime This command displays th e timeout for address aging.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-2 5 202-10088-01, March 2005 Locally Administered MAC Address If desired, a locally administered MAC address can be configured for in-band conn ectivity . T o take effect, 'MAC Address T ype' must be set to 'L ocally Administered'.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-26 Switching Comm a nd s 202-10088-01, March 2005 Allow New T elnet Sessions Indicates that new telnet sessio ns will not be allowed when set to no. The factory defaul t value is yes.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-2 7 202-10088-01, March 2005 ServPort Configuration Protocol Current Indicates what network protocol was used on the last, or current power-up cycle, if any .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-28 Switching Comm a nd s 202-10088-01, March 2005 Access Mode The access level for th is community string. St atus The status of this community access entry . show snmptrap This command displays SNMP trap receivers.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-2 9 202-10088-01, March 2005 Multiple Users Flag May be enabled or disabled.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-30 Switching Comm a nd s 202-10088-01, March 2005 snmp-server community ip addr This command sets a client IP address for an SNMP community .
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-3 1 202-10088-01, March 2005 Mode Global Config snmp-server community mode This command activates an SN MP community . If a community is enabled, an SNMP manager associated with this community ma nages the switch according to its access right.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-32 Switching Comm a nd s 202-10088-01, March 2005 snmp-server enable trap s This command enables th e Authentication Flag. Default enabled Format snmp-server enable traps Mode Global Config no snmp-server enable trap s This command disables th e Authenti ca tio n F lag .
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-3 3 202-10088-01, March 2005 Mode Global Config no snmp-server enable trap s linkmode This command disables Link Up/D own traps for the entire switch.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-34 Switching Comm a nd s 202-10088-01, March 2005 snmptrap This command adds an SNMP trap name. Th e maximum length of name is 16 case-sensitive alphanumeric characters. Default The default name for the six undefined co mmun ity names is Delete.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-3 5 202-10088-01, March 2005 Format no snmptrap mode < name> <ipaddr> Mode Global Config snmp trap link-st atus This command enables link status traps by interface.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-36 Switching Comm a nd s 202-10088-01, March 2005 Management VLAN Command This command is used to set the Management VLAN. network mgmt_vlan This command configures the Managemen t VLAN ID.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-3 7 202-10088-01, March 2005 Mode Interface Config no auto-negotiate This command disables automatic negotiation on a port. Note: Automatic sensing is disabled when automatic negotiation is disabled.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-38 Switching Comm a nd s 202-10088-01, March 2005 macfilter This command adds a static MAC filter entr y for the MAC address <macaddr> on the VLAN <vlanid>.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-3 9 202-10088-01, March 2005 no macfilter adddest This command removes a port fro m the dest ination filter set for the MAC filter wi th the given <macaddr> and VLAN of <vlanid>.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-40 Switching Comm a nd s 202-10088-01, March 2005 Mode Interface Config no macfilter addsrc This command removes a port from the source filte r set for the MAC filter with the MAC address of <macaddr> and VLAN of <v lanid>.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-4 1 202-10088-01, March 2005 Format monitor session source <slot/port > < destination> < .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-42 Switching Comm a nd s 202-10088-01, March 2005 no shut down This command enables a port. Format no shutdown Mode Interface Config shut down all This command disables all ports.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-4 3 202-10088-01, March 2005 Format speed all { <100 | 10> <half-duplex | full-duplex>} Mode.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-44 Switching Comm a nd s 202-10088-01, March 2005 Format no storm-control broadcast Mode Global Config storm-control f lowcontrol This command enables 802.3x fl ow control for the switch.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-4 5 202-10088-01, March 2005 T ype This displays th e type of the entry . Stat ic entries are those that a re configured by the end user . Dynamic entries are added to the table as a result of a learning pro- cess or protocol.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-46 Switching Comm a nd s 202-10088-01, March 2005 T ype This displays th e type of the entry . Stat ic entries are those that a re configured by the end user . Dynamic entries are added to the table as a result of a learning pro- cess or protocol.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-4 7 202-10088-01, March 2005 Format show port { < slot/port > | all } Mode Privileged EXEC Slot/Port V alid slot and port number separated by forward slashes.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-48 Switching Comm a nd s 202-10088-01, March 2005 VLAN Thi s fie ld indicates the VLAN associ ated with this Protocol Group. Interface(s) This field lists the slot/port interface (s ) that are associat ed with thi s P rotoc ol Group.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-4 9 202-10088-01, March 2005 vlan accept frame This command sets the frame ac ceptance mode per interface. Fo r VLAN Only mode, untagged frames or priority frames received on this interfa ce are discarded.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-50 Switching Comm a nd s 202-10088-01, March 2005 vlan makest atic This command changes a dynamically created VLAN (one that is created by GVRP registration) to a static VLAN (one that is permanently configured and defined).
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-5 1 202-10088-01, March 2005 exclude The interface is never a member of this VLAN. This is equivalent to registration forbidden. auto The interface is dynamically regi stered in this VLAN by GVRP .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-52 Switching Comm a nd s 202-10088-01, March 2005 no vlan port accept frame all This command sets the frame acceptance mode for all interfaces to Admit All .
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-5 3 202-10088-01, March 2005 Format no vlan port pvid all Mode Global Config vlan port t agging all This command configures the tagging behavior for all interfaces in a VLAN to enabled.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-54 Switching Comm a nd s 202-10088-01, March 2005 Mode Global Config no vlan protocol group add protocol This command removes the < protocol> from this protocol-based VLAN gr oup that is identified by this < groupid> .
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-5 5 202-10088-01, March 2005 protocol vlan group This command adds the physical < slot/port > inter face to the protoc ol-based VLAN identifie d by < groupid > .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-56 Switching Comm a nd s 202-10088-01, March 2005 Format no protocol vlan group all <groupid> Mode Global Config vlan pvid This command changes the VLAN ID per interface.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-5 7 202-10088-01, March 2005 Format show vlan <vlanid> Mode Privileged EXEC and User EXEC VLAN ID There is a VLAN Identifier (VID) a ssociated with ea ch VLAN.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-58 Switching Comm a nd s 202-10088-01, March 2005 Untagged - specifies to transmit traffic for this VLAN as untagged frames. show vlan brief This command displays a list of all configured VLANs.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-5 9 202-10088-01, March 2005 port. W ith either option, VLAN tagged frames are forwarded in accordance to the 802.1Q VLAN specification. Ingress Filtering May be enabled or disabled.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-60 Switching Comm a nd s 202-10088-01, March 2005 clear config This command resets the configur ation to the factory defaults without p owering of f the switch. The switch is automatically reset when this comm and is processed.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-6 1 202-10088-01, March 2005 Mode Privileged EXEC clear port-channel This command clears all port-channels (LAGs). Format clear port-channel Mode Privileged EXEC clear traplog This command clears the trap log.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-62 Switching Comm a nd s 202-10088-01, March 2005 ping This command checks if another computer is on the network and listens for connections. T o use this command, configure the switch for network (in-band) connection.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-6 3 202-10088-01, March 2005 The command c an be used to th e save the runn ing configuration to n vram .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-64 Switching Comm a nd s 202-10088-01, March 2005 CLI Command Logging This section provides a detailed explana tion of the CLI Command Logging comma nds. logging cli-command This command enables the CL I command Logging feature.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-6 5 202-10088-01, March 2005 configscript apply This command applies the commands in the c onfiguration script to the switch. The apply command backs up the ru nning configuratio n and then starts applying the commands in the script file.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-66 Switching Comm a nd s 202-10088-01, March 2005 configscript validate This command validates a configuration script file by parsing each line in the script file where <scriptname> is the name of the script to be valid ated.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-6 7 202-10088-01, March 2005 logging buffered This command enables logging to in-memory log where up to 128 logs are kept.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-68 Switching Comm a nd s 202-10088-01, March 2005 Default disabled; critical Format logging console [severitylevel] Mode Global Config no logging console This command disables lo gging to the console.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-6 9 202-10088-01, March 2005 logging host remove This command disables logging to host.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-70 Switching Comm a nd s 202-10088-01, March 2005 show logging This command displays logging.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-7 1 202-10088-01, March 2005 Log Messages: The number of messages received by the log process. This includes messages that are dropped or ignored show logging buffered This command displays buffered logging (s ystem startup and system operation logs).
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-72 Switching Comm a nd s 202-10088-01, March 2005 Host St atus The state of logg ing to configured syslog hosts. If the status is disable, no logging occurs. Simple Network T ime Protocol (SNTP) This section provides a detailed explanation of the SNTP commands.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-7 3 202-10088-01, March 2005 sntp client mode This command will disable Simple Networ k T ime Protocol (SNTP) client mode.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-74 Switching Comm a nd s 202-10088-01, March 2005 sntp unicast client poll-timeout This command will set the poll timeout for SNTP uni cast clients in seconds to a value from 1-30.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-7 5 202-10088-01, March 2005 no sntp multicast client poll- interval This command will reset the poll interval for SNTP multicast clients to its default value.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-76 Switching Comm a nd s 202-10088-01, March 2005 Multicast Count Current number of unsolicited multicast messages that ha ve been received and processed by the SNTP client since la st reboot show sntp client This command is used to di splay SNTP client settings.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-7 7 202-10088-01, March 2005 Address T ype Address T ype of configured SNTP server . Priority IP priority type of the config ured server . Ve r s i o n SNTP V ersion number of the server .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-78 Switching Comm a nd s 202-10088-01, March 2005 case sensitive. T wo users are incl uded as the factory default, ‘admin’ and ‘guest’. Connection From IP address of the telnet client machine or EIA-232 for the serial port connection.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-7 9 202-10088-01, March 2005 users name This command adds a new user (account) if spac e permits. The account <username> can be up to eight characters in length.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-80 Switching Comm a nd s 202-10088-01, March 2005 users snmpv3 accessmode This command specifies the snmpv3 access priv ileges for the specified login user . The valid accessmode values are readonly or readwrite .
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-8 1 202-10088-01, March 2005 users snmpv3 encryption This command specifies the encryp tion protocol to be used for the specified login user . The valid encryption protoc ols are des or none.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-82 Switching Comm a nd s 202-10088-01, March 2005 client-identifier This command specifies the uniq ue identifier for a DHCP client. Unique-identifier is a valid notation in hexadecimal format.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-8 3 202-10088-01, March 2005 default-router This command specifies the defau lt router list for a DHCP client. { addr ess1, address2… addr ess8 } are valid IP addresses, each made up of four decimal bytes ranging from 0 to 255.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-84 Switching Comm a nd s 202-10088-01, March 2005 T ype indicates the protocol of the hardware plat form.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-8 5 202-10088-01, March 2005 Mode Global Config no ip dhcp excluded-address This command removes the excluded IP addr esses for a DHCP client.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-86 Switching Comm a nd s 202-10088-01, March 2005 Format ip dhcp pool <name> Mode Global Config Mode no ip dhcp pool This command removes the DHCP address pool. The name should be pre viously configured pool name.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-8 7 202-10088-01, March 2005 no network This command removes the subnet number and mask. Format no network Mode DHCP Pool Config service dhcp This command enables the DHCP server and relay agent features on the ro uter .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-88 Switching Comm a nd s 202-10088-01, March 2005 domain-name This command specifies th e domain name for a DHCP client. The <domain> specifies the domain name string of the client.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-8 9 202-10088-01, March 2005 no ip dhcp conflict logging This command disables conflic t logging on DHCP server .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-90 Switching Comm a nd s 202-10088-01, March 2005 Format netbios-node-type <type> Mode DHCP Pool Config no netbios-node-type This command removes the NetBIOS node T ype.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-9 1 202-10088-01, March 2005 Format option <code> {ascii string | hex <s tring1> [<string2>...<string8> ] | ip <addre ss1> [<address2>.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-92 Switching Comm a nd s 202-10088-01, March 2005 Excluded Address The ranges of IP addresses that a DHCP server should not assign to DHCP clients. show ip dhcp pool configuration This command displays pool configuration.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-9 3 202-10088-01, March 2005 Manual bind ings The number of IP addresses that have been manually map ped to the MAC addresses of hosts tha t are found in the DHCP dat abase.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-94 Switching Comm a nd s 202-10088-01, March 2005 clear ip dhcp binding This command deletes an automatic address bindi ng from the DHCP server database. If “*” is specified, the bindings corresponding to all the addresses are deleted.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-9 5 202-10088-01, March 2005 classofservice dot1pmapping This command maps an 802.1p pr iority to an internal traffic class for a device when in ‘Global Config’ mode.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-96 Switching Comm a nd s 202-10088-01, March 2005 Default 0 Format vlan priority <priority> Mode Interface Config GARP Commands This chapter provides a detailed explanation of the GARP comm ands.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-9 7 202-10088-01, March 2005 set garp timer join all This command sets the GVRP join time for all port s and per GARP .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-98 Switching Comm a nd s 202-10088-01, March 2005 Mode Interface Config set garp timer leave all This command sets the GVRP leave time for all ports.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-9 9 202-10088-01, March 2005 Note: This command has an effect only when GVRP is enabled . Format no set garp timer leaveall Mode Interface Config set garp timer leaveall all This command sets how frequently Leave All PDUs are gene rated for all ports.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-100 Switching Comm a nd s 202-10088-01, March 2005 GARP VLAN Registration Protocol (GVRP) Commands This chapter provides a detailed explanation of the GVRP comm ands.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-101 202-10088-01, March 2005 set gvrp interfacemode all This command enables GVRP (GARP VLAN Registration Protocol ) for all ports.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-102 Switching Comm a nd s 202-10088-01, March 2005 instance of this timer on a per -Por t, pe r -GARP participant basis. The Leave All Period T i mer is set to a random value in the range o f LeaveAllT ime to 1.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-103 202-10088-01, March 2005 set gmrp interfacemode This command enables GARP Multicast Registration Protocol on a selected interface.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-104 Switching Comm a nd s 202-10088-01, March 2005 Mode Global Config show gmrp configuration This command displa ys Ge neric Attributes Reg ist ration Protocol (GARP) information for one or all interfaces.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-105 202-10088-01, March 2005 Mode Privileged EXEC Mac Address A unicast MAC address for which the sw itch has forwarding and or filtering information.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-106 Switching Comm a nd s 202-10088-01, March 2005 no set igmp This command disables IGMP Snooping on the system. Format no set igmp Mode Global Config set igmp This command enables IGMP Snooping on a select ed interface.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-107 202-10088-01, March 2005 Format no set igmp groupmembership-interval Mode Global Config set igmp interfacemode all This command enables IGMP S nooping on all interfaces.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-108 Switching Comm a nd s 202-10088-01, March 2005 set igmp mcrtrexpiretime This command sets the Mu lticast Router Present Expiration time on the system.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-109 202-10088-01, March 2005 Multicast Control Frame Count This displays the number of mul tic as t co ntrol frames that ar e pro- cessed by the CPU.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-110 Switching Comm a nd s 202-10088-01, March 2005 Mode Vlan Mode no set igmp This command disables IGMP sn ooping on a particular VLAN, and in turn disabling IGMP snooping on all interfaces pa rticipating in this VLAN.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-111 202-10088-01, March 2005 Format set igmp maxresponse <vlanId> <1-359 9> Mode Vlan Mode no set igmp maxresponse This command sets the IGMP Maximum Resp onse time on the VLAN to the default value.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-112 Switching Comm a nd s 202-10088-01, March 2005 Fast-leave admin mode should be enabled only on VLANs where only one host.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-113 202-10088-01, March 2005 Fast Leave Mode This indicates whether or not IGMP Snooping Fast-leave is active on the VLAN.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-114 Switching Comm a nd s 202-10088-01, March 2005 no port-channel st aticcap ability This command disables the support of static po rt-channels (link aggregations - LAGs) on the device.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-115 202-10088-01, March 2005 port-channel This command configures a new port-channel (LAG) and generates a logica l slot/port number for the port-channel.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-116 Switching Comm a nd s 202-10088-01, March 2005 Default enabled Format port-channel linktrap { < logical slot /port > | all} Mode Global Config no port-channel linktrap This command disables link trap notifications fo r the port-channel (LAG).
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-117 202-10088-01, March 2005 Active Port s This field lists the ports that are actively participating in this port- channel. show port-channel This command displays an overview of all port-channels (LAGs) on the switch.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-118 Switching Comm a nd s 202-10088-01, March 2005 S p anning T ree (STP) Commands This chapter provides a detailed explanation of the Spanning T ree comm ands.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-119 202-10088-01, March 2005 Default disabled Format spanning-tree Mode Global Config no sp annin g-tree This command sets the spanning-t ree operational mode to disabled.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-120 Switching Comm a nd s 202-10088-01, March 2005 no sp anning-tree configuration revis ion This command sets the Configur ation Identifier Revision Level for use in identifying the configuration that this switch is curren tly using to the default value, i.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-121 202-10088-01, March 2005 no sp annin g-tree forceversion This command sets the Force Protocol V ersion parameter to the default value, i.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-122 Switching Comm a nd s 202-10088-01, March 2005 This command sets the admin Hello T i me parameter for the common and inte rnal spanning tree to the default value.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-123 202-10088-01, March 2005 If the ‘external-cost’ token is spec ified, this command sets the external-path cost for MST ins tance ‘0’ i.e. CIST instance.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-124 Switching Comm a nd s 202-10088-01, March 2005 sp anning-tree mst inst ance This command adds a multiple spanning tree instance to the switc h. The instance <mstid> is a number within a range of 1 to 4094, that corresp onds to the new instance I D to be added.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-125 202-10088-01, March 2005 If 0 (defined as the default CIST ID) is passed as the <mstid>, then this command sets the Bridge Priority parameter for the common and internal sp anning tree to the default value, i.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-126 Switching Comm a nd s 202-10088-01, March 2005 sp anning-tree port mode all This command sets the Admini strative Switch Port State for all ports to enabled.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-127 202-10088-01, March 2005 no sp annin g-tree bp d umigrationc heck This command disables BPDU migratio n check on a given interface. The all option disables BPDU migration check on all interfaces.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-128 Switching Comm a nd s 202-10088-01, March 2005 CST Regional Root Bridge Identifier of the common sp anning tree regional root. It is derived using the bridge priority and the bas e MAC address of the bridge.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-129 202-10088-01, March 2005 MSTP BPDUs T ransmitted Multiple Spanning T ree Protocol Bridge P rotocol D ata Units sent MSTP BPDUs Received Multiple S panning Tree Protocol Bridge Protocol D ata Units received.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-130 Switching Comm a nd s 202-10088-01, March 2005 Port Priority The priority for a particular port within th e selected MST instance .
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-131 202-10088-01, March 2005 Point T o Point MAC St atus Derived value indicating if this port is part of a point to point link . CST Regional Root The regional root identifier in use for this port.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-132 Switching Comm a nd s 202-10088-01, March 2005 Associated FIDs List of forwarding database id entifiers associated with this instance . Associated VLANs List of VLAN IDs associat ed with this instance.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-133 202-10088-01, March 2005 sp anning-tree max-hop s This command sets the MSTP Max Hops paramete r to a new value for the common and internal spanning tree.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-134 Switching Comm a nd s 202-10088-01, March 2005 If the ‘port-priority’ token is specified, this command sets the prio.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-135 202-10088-01, March 2005 This command sets the Admin Hello T ime paramete r to a new value for th e comm on and internal spanning tree.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-136 Switching Comm a nd s 202-10088-01, March 2005 Root Port Bridge Forward Delay Derived value Hello Time Configure d value.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Switching Commands 8-137 202-10088-01, March 2005 STP BPDUs T ransmitted Spanning T ree Protocol Bridge Protocol Data Units sent STP BPDUs Received S panning T ree Protocol Bri dge Protocol Data Units received.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 8-138 Switching Comm a nd s 202-10088-01, March 2005 If 0 (defined as the default CIST ID) is passed as the <mstid>, then this command displays the settings and parameters for a specific switch port within the common and in ternal spanning tree.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Security Commands 9-1 202-10088-01, March 2005 Chapter 9 Security Commands This section provides a detailed explanation of the Security commands.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 9-2 Security Commands 202-10088-01, March 2005 Modes Global Config Interface Config port-security max-dynamic This command sets the maximum of dynamically locked MAC addresses allowed on a specific port.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Security Commands 9-3 202-10088-01, March 2005 port-security mac-address This command adds a MAC address to the list of statically locked MAC addresses.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 9-4 Security Commands 202-10088-01, March 2005 show port-security This command displays the port-secu rity settings for the entire system.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Security Commands 9-5 202-10088-01, March 2005 show port-security violation This command displays the source MAC address of the la st packet that was discarded on a locked port.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 9-6 Security Commands 202-10088-01, March 2005 Format authentication login <listname> [met hod1 [method2 [method3]]] Mode Global Config no authentication login This command deletes the specified authentication login list.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Security Commands 9-7 202-10088-01, March 2005 Format dot1x defaultlogin <listname> Mode Global Config dot1x initialize This command begins the initializa tion sequence on the specified po rt.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 9-8 Security Commands 202-10088-01, March 2005 dot1x port-control This command sets the authentica tion mode to be used on the sp ecified port. . The control mode may be one of the follow ing.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Security Commands 9-9 202-10088-01, March 2005 Mode Global Config no dot1x port-control All This command sets the auth entication mode to be used on all ports to 'auto'.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 9-10 Security Commands 202-10088-01, March 2005 Format dot1x system-auth-control Mode Global Config no dot1x system-auth-control This command is used to disable the dot1x authentica tion support on the switch.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Security Commands 9-11 202-10088-01, March 2005 Format dot1x timeout {{reauth-period <secon ds>} | {quiet- period <s.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 9-12 Security Commands 202-10088-01, March 2005 IP Address The configured IP address of the RADIUS accounting server Port The .
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Security Commands 9-13 202-10088-01, March 2005 Format show authentication Mode Privileged EXEC Authentication Login List This displays the authen tication login listname. Method 1 This displays the first method in the sp ecified authentication login list, if any .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 9-14 Security Commands 202-10088-01, March 2005 Control Mode The conf igured control mode for th is port. Possible values are force-unautho- rized | force-authorized | auto Operating Control Mode The control mode under wh ich this port is operating.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Security Commands 9-15 202-10088-01, March 2005 Reauthentication Enabled Indicat es if rea uthe ntication is enable d on this port. Possible values are ‘T rue” or “False”.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 9-16 Security Commands 202-10088-01, March 2005 show dot1x users This command displays 802.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Security Commands 9-17 202-10088-01, March 2005 Note that the login list associated with the ‘admin ’ user can not be changed to prevent accidental lockout from the switch.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 9-18 Security Commands 202-10088-01, March 2005 If the 'auth' token is used, the command configur es the IP address to use to connect to a RADIUS authentication server .
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Security Commands 9-19 202-10088-01, March 2005 radius server key This command is used to configure the shared se cret between the RADIUS client and the RADIUS accounting / authentication server .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 9-20 Security Commands 202-10088-01, March 2005 Format radius server retransmit <retries> Mode Global Config no radius s.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Security Commands 9-21 202-10088-01, March 2005 Number of configured servers The configured IP address of the authentication .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 9-22 Security Commands 202-10088-01, March 2005 Access Retransmission The number of RADIUS Access- Request packets retransmitted to this RADIUS authentication server .
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Security Commands 9-23 202-10088-01, March 2005 Mode Privileged EXEC no ip ssh This command is used to disable SSH. Format no ip ssh Mode Privileged EXEC ip ssh protocol This command is used to set or remove protocol levels (or v ersi ons) for SSH.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 9-24 Security Commands 202-10088-01, March 2005 ip http secure-port This command is used to set th e sslt port where port can be 1-65535 an d the default is port 443.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Security Commands 9-25 202-10088-01, March 2005 ip http server This command enables access to the switch through the W eb inte rface. When access is ena bled, the user can login to the switch from the W eb inte rface.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 9-26 Security Commands 202-10088-01, March 2005.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Routing Commands 10-1 202-10088-01, March 2005 Chapter 10 Routing Commands This chapter provides a detailed expl anation of the Routing commands. Address Resolution Prot ocol (ARP) Commands This chapter provides a detailed explanation of the ARP commands .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 10-2 Routing Commands 202-10088-01, March 2005 Mode Global Config ip proxy-arp This command enables proxy ARP on a router interface.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Routing Commands 10-3 202-10088-01, March 2005 arp dynamicrenew This command enables ARP comp onent to automatically renew ARP entries of type dynamic when they age out.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 10-4 Routing Commands 202-10088-01, March 2005 arp retries This command configures the ARP coun t of maximum request for retries. The value for <retries> is an inte ger , which represents the maximum number of request f or retries.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Routing Commands 10-5 202-10088-01, March 2005 Format clear arp-cache [gateway] Mode Privileged Exec show arp This command displays the Address Resolution Pr otocol (ARP) cache.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 10-6 Routing Commands 202-10088-01, March 2005 show arp br ief This command displays the brief Address Re solution Protocol (ARP ) table information. Format show arp brief Mode Privileged EXEC Age Ti me (seconds) Is the time it takes for an ARP en try to age out.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Routing Commands 10-7 202-10088-01, March 2005 The current value for this func tio n is displayed under "show ip interface" labeled as "Routing Mode".
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 10-8 Routing Commands 202-10088-01, March 2005 Mode Interface Config no ip address This command deletes an IP address from an interface. The value for <ipaddr> is the IP Address of the interface.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Routing Commands 10-9 202-10088-01, March 2005 Format ip route default <nextHopRtr> [<pref erence>] Mode Global Config no ip route default This command deletes all config ured default routes.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 10-10 Routing Comm a nd s 202-10088-01, March 2005 Format ip forwarding Mode Global Config no ip forwarding This command disables forwarding of IP frames.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Routing Commands 10-11 202-10088-01, March 2005 Mode Interface Config show ip brief This command displays all the summary information of the IP . This command takes no options.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 10-12 Routing Comm a nd s 202-10088-01, March 2005 Link S peed Dat a Rate Is an integer representing the physic al link data rate of the speci- fied interface. This is measured in Me gabits per second (Mbps).
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Routing Commands 10-13 202-10088-01, March 2005 Subnet Mask Is a mask of the network and host portion of the IP address for the router interface. Protocol T ells which protocol added the specified route.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 10-14 Routing Comm a nd s 202-10088-01, March 2005 Mode Privileged EXEC Network Address Is a valid network address identif ying the network on the speci- fied interface. Subnet Mask Is a mask of the network and host portion of the IP address for the attached network.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Routing Commands 10-15 202-10088-01, March 2005 encap sulation This command configures the link layer encapsula tion type for th e packet . Acceptable values for <encapstype> are Ethernet an d SNAP .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 10-16 Routing Comm a nd s 202-10088-01, March 2005 bootp dhcprelay enable This command enables the forwar ding of relay reque sts for BootP/DHCP Relay on the sys tem.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Routing Commands 10-17 202-10088-01, March 2005 Format bootpdhcprelay minwaittime <0-100> Mode Global Config no bootp dhcprelay minwaittime This command configures the default mini mum wa it time in seconds for BootP/DHCP Relay on the system.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 10-18 Routing Comm a nd s 202-10088-01, March 2005 Request s Received Is the number or requests received. Request s Relayed Is the number of requests relayed. Packet s Discarded Is the number of packets discarded.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Routing Commands 10-19 202-10088-01, March 2005 Mode Interface Config no ip ird p address This command configures the default address to be used to advertise the r outer for the interface.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 10-20 Routing Comm a nd s 202-10088-01, March 2005 ip ird p minadvertinterval This command configures the minimum time, in seconds, allowed between sending router advertisements from the interfa ce.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Routing Commands 10-21 202-10088-01, March 2005 Mode Privileged EXEC and User EXEC Ad Mode Displays the advertise mode which indicates whether route r dis- covery is enabled or disabled on this interface.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 10-22 Routing Comm a nd s 202-10088-01, March 2005 Mode VLAN Database show ip vlan This command displays the VLAN routing informat i on for all VLANs with rout ing enabled in the system.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Routing Commands 10-23 202-10088-01, March 2005 no enable (RIP) This command sets the admi nistrative mode of RIP in the router to inactive. Format no enable Mode Router RIP Config ip rip This command enables RIP on a router interface.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 10-24 Routing Comm a nd s 202-10088-01, March 2005 Format default-information originate Mode Router RIP Config no default-information originate (RIP) This command is used to control the advertisement of default routes.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Routing Commands 10-25 202-10088-01, March 2005 distribute-list out This command is used to specif y the access list to filter routes received from the source protocol.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 10-26 Routing Comm a nd s 202-10088-01, March 2005 no ip rip authentication This command sets the default RI P V ersion 2 Authentication T ype.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Routing Commands 10-27 202-10088-01, March 2005 no ip rip send version This command configures the interface to allow RI P control packets of the default version to be sent.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 10-28 Routing Comm a nd s 202-10088-01, March 2005 redistribute This command config ures RIP protocol to redistribu te rou tes from the specified so urc e protocol/ routers. Ther e are five poss ible match option s.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Routing Commands 10-29 202-10088-01, March 2005 Auto Summary Mode Select enable or disable from the pulldown menu. If you select enable groups of adjacent routes will be summarized into single entries, in order to reduce the to tal number of entries The defaul t is enable.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 10-30 Routing Comm a nd s 202-10088-01, March 2005 show ip rip interface This command displays information re lated to a particular RIP interface.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Quality of Service (QoS) Commands 11-1 202-10088-01, March 2005 Chapter 11 Quality of Service (QoS) Commands This chapter provides a detailed explanation of the Quality of Service (QOS) commands.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 11-2 Quality of Service (Q oS) Comm ands 202-10088-01, March 2005 Note: The CLI mode is changed to Mac-Access-List Config when this command is successfully executed.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Quality of Service (QoS) Commands 11-3 202-10088-01, March 2005 The Ethertype may be specified as either a ke yword or a four -digit hexadecimal value from 0x0600-0xFFFF .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 11-4 Quality of Service (Q oS) Comm ands 202-10088-01, March 2005 no mac access-group <name> {in|out} This comman d removes a M AC ACL identified by <name> from the interface in a given direction.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Quality of Service (QoS) Commands 11-5 202-10088-01, March 2005 Note: This does not include the implicit 'deny all' rule defined at the end of every MAC ACL.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 11-6 Quality of Service (Q oS) Comm ands 202-10088-01, March 2005 no access-list This command deletes an ACL that is identified by the parameter < accesslistnumber> from the system .
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Quality of Service (QoS) Commands 11-7 202-10088-01, March 2005 Source IP Mask This field displays the source IP Mask for this rule. Source Port s This field displays the source port range for this rule.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 11-8 Quality of Service (Q oS) Comm ands 202-10088-01, March 2005 Note that the type of class - all, any , or acl - ha s a bea ring on the validity of match criteria specified when defining the class.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Quality of Service (QoS) Commands 11-9 202-10088-01, March 2005 Format diffserv Mode Global Config no diffserv This command sets the DiffServ operational mo de to inactiv e. While disabled, the DiffServ configuration is retained and can be changed, bu t it is not ac tivated.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 11-10 Quality of Service (QoS) Commands 202-10088-01, March 2005 The class type of match-all indicates all of the individual match conditions must be true for a packet to be consider ed a member of the cla ss.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Quality of Service (QoS) Commands 11-11 202-10088-01, March 2005 class-map rename This command changes the name of a DiffServ class. The <classname> is the name of an existing DiffServ class.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 11-12 Quality of Service (QoS) Commands 202-10088-01, March 2005 match any This command adds to the spec ified class definition a match c ondition whereby all packets are considered to belong to the class.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Quality of Service (QoS) Commands 11-13 202-10088-01, March 2005 no match class-map This command removes from the sp ecified class definition the set of match conditions defined for another class.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 11-14 Quality of Service (QoS) Commands 202-10088-01, March 2005 match dstip This command adds to the specif ied class definition a match cond ition based on the destination IP address of a packet.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Quality of Service (QoS) Commands 11-15 202-10088-01, March 2005 match ip dscp This command adds to the specif ied class defi.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 11-16 Quality of Service (QoS) Commands 202-10088-01, March 2005 match ip tos This command adds to the specif ied class defini.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Quality of Service (QoS) Commands 11-17 202-10088-01, March 2005 Mode Class-Map Config match source-address mac This command adds to the spec ified class definition a match c ondition based on the source MAC address of a packet.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 11-18 Quality of Service (QoS) Commands 202-10088-01, March 2005 T o specify the match condition as a numeric value, one layer 4 port number is required. The port number is an integer from 0 to 6553 5.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Quality of Service (QoS) Commands 11-19 202-10088-01, March 2005 The DiffServ CLI does not necessarily require th at users associate only one traffic class to one policy .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 11-20 Quality of Service (QoS) Commands 202-10088-01, March 2005 redirect This command specifies that all in coming packets for the associated traf fic stream a re redirected to a specific egress interface (physical port or port-channel).
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Quality of Service (QoS) Commands 11-21 202-10088-01, March 2005 Incomp atibilities Expedite (all forms) bandwid th percent T.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 11-22 Quality of Service (QoS) Commands 202-10088-01, March 2005 no class This command deletes the instance of a partic ular class and its defined treatment from the specified policy .
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Quality of Service (QoS) Commands 11-23 202-10088-01, March 2005 Note: The actual bandwidth allocation do es not occur until the policy is attached to an interface in a particular direction.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 11-24 Quality of Service (QoS) Commands 202-10088-01, March 2005 Policy T ype In Incomp atibilities Mark IP Precedence, Police (all forms) mark ip-precedence This command marks all packets for the associated tra ffic stream with the specified IP Precedence value.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Quality of Service (QoS) Commands 11-25 202-10088-01, March 2005 Restrictions Only one style of police command (s imple, singlerate, tworate) is allowed for a given class instance in a particular policy .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 11-26 Quality of Service (QoS) Commands 202-10088-01, March 2005 police-two-rate This command is used to establis h the traf fic policing style for th e specified class.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Quality of Service (QoS) Commands 11-27 202-10088-01, March 2005 policy-map This command establishes a new Dif fServ pol icy . The < policyname> parameter is a case-sensitive alphanumeric string from 1 to 31 characters uniquely identifying the policy .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 11-28 Quality of Service (QoS) Commands 202-10088-01, March 2005 The remaining parameters are a ll optional. The fourth data pa rameter is the sampling rate, indicating the period at which the queue is sample d for computing the average depth.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Quality of Service (QoS) Commands 11-29 202-10088-01, March 2005 Note: Queue depth management defaults to tail d rop, but the randomdrop command c an b e used to change to a RED scheme.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 11-30 Quality of Service (QoS) Commands 202-10088-01, March 2005 Note: This command shall fail if an y attributes within the policy definition exceed the capabilities of the interface.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Quality of Service (QoS) Commands 11-31 202-10088-01, March 2005 show class-map This command displays all configuration information for the specified class. The <classname> is the name of an existing DiffServ class.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 11-32 Quality of Service (QoS) Commands 202-10088-01, March 2005 Class T ype The class type (all, any , or ac l) indicating how the match cri- teria are evaluated for this class.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Quality of Service (QoS) Commands 11-33 202-10088-01, March 2005 Policy Attribute T able Size The current number of entries (rows) in the Policy Att ribute Ta b l e . Policy Attribute T able Max The maximum allowed entries (rows) for the Policy Attribute Ta b l e .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 11-34 Quality of Service (QoS) Commands 202-10088-01, March 2005 ing action. It may also be sp ecified along with a QoS queue assignment. If the Policy Name is specified the following fields are displayed: Policy Name The name of thi s policy .
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Quality of Service (QoS) Commands 11-35 202-10088-01, March 2005 Conform DSCP V alue This field shows the DSCP mark value if the conform action is markdscp. Conform IP Precedence V alue This field shows the IP Prec edence mark value if the con- form action is markprec.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 11-36 Quality of Service (QoS) Commands 202-10088-01, March 2005 Random Drop Maximum Th reshold This field displays the RED maximum thresh- old.This is not displayed if th e queue depth management scheme is not RED.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Quality of Service (QoS) Commands 11-37 202-10088-01, March 2005 Policy Det ails Attached policy details, whose co ntent is identical to that described for the show policy -map <policymapname> command (content not repeated here for brevity).
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 11-38 Quality of Service (QoS) Commands 202-10088-01, March 2005 Policy Name The name of the policy attached to the interface in the indicated direction.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Quality of Service (QoS) Commands 11-39 202-10088-01, March 2005 Sent Octet s/Packet s A count of the octets/packets fo rwarded for this class instance after the defined DiffServ treatment was applied.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 11-40 Quality of Service (QoS) Commands 202-10088-01, March 2005 Policy Name The name of the policy attached to the interface. Note: None of the counters listed here are guaranteed to be supported on all platforms.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Quality of Service (QoS) Commands 11-41 202-10088-01, March 2005 Modes Global Config Interface Config classofservice ip-p recedence-mapping This command maps an IP preced ence value to an internal traffi c class.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 11-42 Quality of Service (QoS) Commands 202-10088-01, March 2005 no cos-queue max-bandwidth This command restores the default for each queue's maximum bandwidth value.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Quality of Service (QoS) Commands 11-43 202-10088-01, March 2005 Modes Global Config Interface Config cos-queue strict This command activates the strict priority scheduler mode for eac h specified queue.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 11-44 Quality of Service (QoS) Commands 202-10088-01, March 2005 random-detect exponenti al-weighting-const a nt This command sets the d ecay exponent used by the WRED aver age queue depth calcula tion for the interface.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Quality of Service (QoS) Commands 11-45 202-10088-01, March 2005 tail-drop queue-parms <queue-id-1 > [<queue-id-2>.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 11-46 Quality of Service (QoS) Commands 202-10088-01, March 2005 show classofservice ip -precedence-mapping This command displays the current IP Precedence mapping to intern al traffic classes for a specific interface.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Quality of Service (QoS) Commands 11-47 202-10088-01, March 2005 Interface This displays the slot/port of th e interface. If displaying the glo- bal configuration, this output lin e is replaced with a Global Con- fig indication.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 11-48 Quality of Service (QoS) Commands 202-10088-01, March 2005 Interface This displays the slot/port of th e interface. If displaying the glo- bal configuration, this output lin e is replaced with a Global Con- fig indication.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Quality of Service (QoS) Commands 11-49 202-10088-01, March 2005 Queue IdQueue id entification number An interface supports n queues numbered 0 to (n-1). The number n is platform dependent and corresponds to the num- ber of supported queues (traffic classes).
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 11-50 Quality of Service (QoS) Commands 202-10088-01, March 2005.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Managing Switch Stacks 12-1 202-10088-01, March 2005 Chapter 12 Managing Switch S t acks This chapter describes the concepts and reco mmended operating procedures to manage FSM7328S or FSM7352S switches runn ing Release 4.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 12-2 Ma naging Switch Stacks 202-10088-01, March 2005 A switch stack is identified in the network by its network IP address. The network IP address is assigned according to the MAC address of the st ack mas ter .
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Managing Switch Stacks 12-3 202-10088-01, March 2005 If you replace a stack member with an identical model, the new switch fu.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 12-4 Ma naging Switch Stacks 202-10088-01, March 2005 Switch St ack Cabling Figure 12-1 and Figure 12-2 illustrate how individual switches are interconnected to for m a stack. Y ou can use the regular Category 5 Et hernet 8 wire cable.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Managing Switch Stacks 12-5 202-10088-01, March 2005 S t ack Master Election and Re-Election The stack master is el ected or re-e lected based on one of these factors and in the order listed: 1.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 12-6 Ma naging Switch Stacks 202-10088-01, March 2005 Stack members in the same switch stack cannot have the same stack member number .
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Managing Switch Stacks 12-7 202-10088-01, March 2005 Effect s of Replacing a Preconfigu red Switch in a Switch S t ack When a.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 12-8 Ma naging Switch Stacks 202-10088-01, March 2005 Switch St ack Sof tware Compatibility Recommendations All stack members must run the same software version to ensure comp atibility between stack members.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Managing Switch Stacks 12-9 202-10088-01, March 2005 Switch St ack Management Connectivity Y ou manage the switch stack and the stack member interfaces through the stack master .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 12-10 Managing Switch Stacks 202-10088-01, March 2005 S t acking Recommendations The purpose of this section is to collect notes on recommended pr ocedures and expe cted behavior of stacked FSM7328S/FSM7352S.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Managing Switch Stacks 12-11 202-10088-01, March 2005 General Practices • When issuing a comma nd (such as move mana gement, or renumb er), it is recommended that the command has fully completed before issuing th e next command.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 12-12 Managing Switch Stacks 202-10088-01, March 2005 Removing a Unit from the St ack 1. Make sure the redundant stack connection is in place and functional. All stack members should be connected in a logical ring.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Managing Switch Stacks 12-13 202-10088-01, March 2005 • Follow the process in section Removing a Unit from the Stack to remove the desired stack member .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 12-14 Managing Switch Stacks 202-10088-01, March 2005 Moving a Master to a Dif ferent Unit in the S t ack 1. Using the “movemanagement” command, move the master to the d esired unit number .
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Managing Switch Stacks 12-15 202-10088-01, March 2005 Preconfiguration 1. General Information: All config uration on the stack except unit numbers is stored on the management unit.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software 12-16 Managing Switch Stacks 202-10088-01, March 2005 2. All units in the stack must run the same code version. Ports on stack units that don’t match the management unit code version don’ t come up and the show switch command shows a “code mismatch” error .
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software IS CLI Mapping A-1 202-10088-01, March 2005 Appendix A IS CLI Mapping This chapter illustrates the mapp ing between CLI commands and the previous 7300S Series L3 Switch commands.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software A-2 IS CLI Mapping 202-10088-01, March 2005 QOS config acl rule action <acli d> <rulenum> <permit/deny> QOS .
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software IS CLI Mapping A-3 202-10088-01, March 2005 QOS config acl rule match srcl4port range <aclid> <rulenum> <start.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software A-4 IS CLI Mapping 202-10088-01, March 2005 QOS config diffserv policy delete <policyname> Global Config no policy-map &.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software IS CLI Mapping A-5 202-10088-01, March 2005 QOS config diffserv policy police style simple <policyname> <classna me&.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software A-6 IS CLI Mapping 202-10088-01, March 2005 QOS config diffserv policy police action conform markprec <policyname> <c.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software IS CLI Mapping A-7 202-10088-01, March 2005 QOS show diffserv service stat s summary [in/out] Pri vileged EXEC show service-p.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software A-8 IS CLI Mapping 202-10088-01, March 2005 Class-Ma p Config match not cos <0-7> QOS config diffserv class match dstip .
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software IS CLI Mapping A-9 202-10088-01, March 2005 Class-Ma p Config match not ip precedence <0-7> QOS config diffserv class m.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software A-10 IS CLI Mapping 202-10088-01, March 2005 QOS config diffserv class match srcmac <classname> <macaddr> <macm.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software IS CLI Mapping A-11 202-10088-01, March 2005 Routing show router rip interface summary Privileged EXEC and User EXEC show ip .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software A-12 IS CLI Mapping 202-10088-01, March 2005 Routing show router vrrp interface summary Privileged EXEC and User EXEC show ip .
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software IS CLI Mapping A-13 202-10088-01, March 2005 Routing config interface encaps <slot/port> <ethernet/snap> Interfac.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software A-14 IS CLI Mapping 202-10088-01, March 2005 Router RIP Config no enable Routing config router ri p prefrence <0-255> Ro.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software IS CLI Mapping A-15 202-10088-01, March 2005 Routing config router ro ute dele te <networkaddr> <subnetmask> <.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software A-16 IS CLI Mapping 202-10088-01, March 2005 Routing config router vrrp inte rface advinterval <slot/port> <vrID> .
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software IS CLI Mapping A-17 202-10088-01, March 2005 Routing config router bootpdhcprela y cidoptmode <enable | disable> Global.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software A-18 IS CLI Mapping 202-10088-01, March 2005 Router RIP Config no split-horizon Routing config router rip hostroutesaccep t &l.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software IS CLI Mapping A-19 202-10088-01, March 2005 Switching config network javamod e <enable | disable> Privileged EXEC netw.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software A-20 IS CLI Mapping 202-10088-01, March 2005 Switching config snmpcommunity mode <enable | disable> <name> Global .
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software IS CLI Mapping A-21 202-10088-01, March 2005 Switching config trapflags stpmode <enabl e | disable> Global Config snmp-.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software A-22 IS CLI Mapping 202-10088-01, March 2005 Switching show spanningtree bridge Privileged EXEC and User EXEC show spanning-tr.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software IS CLI Mapping A-23 202-10088-01, March 2005 Global Config no spanning-tree configuration name Switching config spanningtree .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software A-24 IS CLI Mapping 202-10088-01, March 2005 Switching config spanningtree bridge priority <0-61440> Removed Switching c.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software IS CLI Mapping A-25 202-10088-01, March 2005 Interface Config no spanning-tree mst <mstid> cost Switching config spanni.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software A-26 IS CLI Mapping 202-10088-01, March 2005 Switching config syslocation <location> Global Config snmp-server location .
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software IS CLI Mapping A-27 202-10088-01, March 2005 Switching transfer download path <path> Switching transfer download filena.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software A-28 IS CLI Mapping 202-10088-01, March 2005 Switching show loginsession Privileged EXEC show loginsession Switching config us.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software IS CLI Mapping A-29 202-10088-01, March 2005 Switching show lags summary Privileged EXEC and User EXEC show port-channel brie.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software A-30 IS CLI Mapping 202-10088-01, March 2005 Switching show mfdb gmrp Pri vileged EXEC show mac-address-table gmrp Switching s.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software IS CLI Mapping A-31 202-10088-01, March 2005 Global Config snmp trap link- status all Global Config no snmp trap link- status.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software A-32 IS CLI Mapping 202-10088-01, March 2005 Global Config deleteport <logical slot/port> all Switching config lag admin.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software IS CLI Mapping A-33 202-10088-01, March 2005 Switching config vlan port tagging <enable | disable> <1-4094> <s.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software A-34 IS CLI Mapping 202-10088-01, March 2005 Switching config protocol delete <gro upi d> Global Config vlan protocol gr.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software IS CLI Mapping A-35 202-10088-01, March 2005 Switching config garp gvrp adminmode <enable | disable> Privileg ed EXEC s.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software A-36 IS CLI Mapping 202-10088-01, March 2005 Interface Config no set garp timer leaveall Global Config set garp timer leaveall.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software IS CLI Mapping A-37 202-10088-01, March 2005 Switching config mirror ing de lete Global Config no set igmp interfacemode all .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software A-38 IS CLI Mapping 202-10088-01, March 2005 Global Config no radius server retransmi t Security config radius timeout <1 -.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software IS CLI Mapping A-39 202-10088-01, March 2005 Security show radius se rver summary Privileged EXEC Security sho w radius serve.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software A-40 IS CLI Mapping 202-10088-01, March 2005 Interface Config no dot1x port-con trol Security con fig dot1x port quietperiod &.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software IS CLI Mapping A-41 202-10088-01, March 2005 Security sho w dot1x summary Privileged EXEC show dot1x [{summary {<slot/port.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software A-42 IS CLI Mapping 202-10088-01, March 2005.
Cabling Guidelines B-1 202-10088-01, March 2005 Appendix B Cabling Guidelines This appendix provides specifications for cabl es used with a NETGEAR NETGEAR 7300S Series Layer 3 Managed Switch. Fast Ethernet Cable Guidelines Fast Ethernet uses UTP cable, as specified in the IEEE 802.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software B-2 Cabling Guidelines 202-10088-01, March 2005 Category 5 Cable Category 5 distributed cable that me ets ANSI/EIA/ TIA-568-A building wiring stan da rds can be a maximum of 328 feet (ft.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Cabling Guidelines B-3 202-10088-01, March 2005 T able 12-4. Electrical Requirement s of Category 5 Cable T wisted Pair Cables For two devices to communicate, th e transmitter of each device must be connected to the receiver of the other device.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software B-4 Cabling Guidelines 202-10088-01, March 2005 Figure 12-4 illustrates crossover twisted pair cable. Figure 12-4: Crossover T wisted-Pair Cable Patch Panels and Cables If you are using patch panels, make sure th at they meet the 100BASE- TX requirements.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Cabling Guidelines B-5 202-10088-01, March 2005 Note : Flat “silver satin” tele phone cable may have the same RJ-45 plug . However , using teleph one cable results in excessive collisio ns, causing the attached port to be partitioned or disconnected from the network.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software B-6 Cabling Guidelines 202-10088-01, March 2005 Unlike 10BASE-T and 100BASE-TX, which use onl y two of the four pairs of wires within the Category 5, 1000BASE-T u ses all four pairs of th e twisted pair .
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Cabling Guidelines B-7 202-10088-01, March 2005 Figure 12-6 shows the RJ-45 plug and RJ-45 connector . Figure 12-6: RJ-45 Plug and RJ-4 5 Connector with Built-in LEDs Ta b l e 1 2 - 1 lists the pin assignments for the 10 /100 Mbps RJ-45 plug an d the RJ-45 connector .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software B-8 Cabling Guidelines 202-10088-01, March 2005 T able 12-2. 100/1000 Mbp s RJ-45 Plug and RJ-45 Conne ctor Pin Assignment s C.
Glossary C-1 202-10088-01, March 2005 Appendix C Glossary Use the list below to find definitions for technical terms used in this manual. Numeric 802.1D The IEEE designator for Spanning Tree Protocol (STP). STP , a link management protocol, is part of the 802.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software C-2 Glossary 202-10088-01, March 2005 100BASE-TX The IEEE specification for 100 Mbps Fast Ethernet over Category 5 twisted-pair cabl e . 1000BASE-SX The IEEE specification for 1000 Mbps Gigabit Ethernet over fib er-optic cable.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Glossary C-3 202-10088-01, March 2005 ASBR See “Autonomous System Boundary Router” on p age 3. Autonomous System Boundary Router ABR located between an OSPF autonom ou s system an d a n on-OSPF network.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software C-4 Glossary 202-10088-01, March 2005 Boot strap Protocol An Internet protocol that enables a diskless workstation to discover its own IP address, the IP address of a BootP server on the network, and a file to be loaded int o memory to boot the machine.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Glossary C-5 202-10088-01, March 2005 Class of Service A term to describe treating different types of traffic wi th different levels of service priority .
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software C-6 Glossary 202-10088-01, March 2005 complex policy or rule statements to determ ine how to forward a given network p acket.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Glossary C-7 202-10088-01, March 2005 transmits that identity to an authenticat ion server su ch as RADIUS. The server asks the AP for proof of identity , which the AP gets from the user and th en send s back to the server to complete the authentication.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software C-8 Glossary 202-10088-01, March 2005 Full-duple x A system that allows packets to be transmitted and received at the same time and, in effect, doubles the potential throughput of a link.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Glossary C-9 202-10088-01, March 2005 GMRP See “GARP Multicast Registrati on Prot ocol” on page 8. GVD GARP VLAN Database. GVRP See “GARP VLAN Registration Protocol” on page 8.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software C-10 Glossary 202-10088-01, March 2005 Internet Control Mess age Protocol ICMP is an extension to the Internet Protocol (IP) that supp orts pack ets containing error , control, and informational messages.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Glossary C-11 202-10088-01, March 2005 L LAN See “Local Area Network” on page 1 1. LDAP See “Lightweight Directory Access Protocol” on page 11. Lightweight Directory Access Protocol A set of protocols for accessing inform ation directories.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software C-12 Glossary 202-10088-01, March 2005 M MAC (1) Medium Access Control. In LANs, the sublayer of the data link control layer that supp orts medium-dependent functions and uses the services of the physical layer to provide services to the logical link control (LLC) sublayer .
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Glossary C-13 202-10088-01, March 2005 MPLS See “Multi-Protocol Label Switching ” on page 13.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software C-14 Glossary 202-10088-01, March 2005 Routers (LSRs) place outgoing labels on the packets. W ith these LSPs, network operators can divert and route traffic based on data-stream type and Internet-a ccess customer .
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Glossary C-15 202-10088-01, March 2005 protocol. This protocol's algorithm determines the shortest path from its router to all th e ot her routers in the network. This protocol is rapidly replacing RIP on the Intern et.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software C-16 Glossary 202-10088-01, March 2005 if necessary . Port mirroring can be managed locally or remotely . An administrato r configures port mirroring by assigning a port from which to copy all packets and another port where those packets will be sent.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Glossary C-17 202-10088-01, March 2005 R RADIUS Short for Remote Auth ent ication Dial-In User Service, RADIUS is an authentication s ystem. Using RADIUS, you must enter your user name and password before gaining access to a network.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software C-18 Glossary 202-10088-01, March 2005 RSVP See “Resource Reservation Setup Protocol” on pa ge 1 7.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Glossary C-19 202-10088-01, March 2005 SNMP See “Simple Network Management Protocol” on page 18. Sp anning T ree A technique that detect s loops in a netw ork and logically block s the redundant pa ths, ensuring that only one route exists between any two LANs.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software C-20 Glossary 202-10088-01, March 2005 TFTP See “TLS” on page 20. TLS Short for Transport Layer Security , TLS is a protocol that guarantees privacy an d data integrity betw een client/server applications co mmunicating over the Internet.
User Manual f or the NETGEAR 7300S Series La yer 3 Managed Switch Software Glossary C-21 202-10088-01, March 2005 an 802.1Q-co mpliant switch or rout er . Devices recognizing 802.1Q-tagged frames mai ntain appropriate tables to track VLANs. The firs t three bits of the 802.
User Manual for the NETGEAR 7300S Seri es Layer 3 Managed Switch Software C-22 Glossary 202-10088-01, March 2005 WINS WINS. W indows Internet Naming Servi ce is a server process for reso lving W indows-based computer names to IP addresses. X XModem One of the most popular file transfer protocols (FTPs).
An important point after buying a device NETGEAR NETGEAR (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought NETGEAR NETGEAR yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data NETGEAR NETGEAR - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, NETGEAR NETGEAR you will learn all the available features of the product, as well as information on its operation. The information that you get NETGEAR NETGEAR will certainly help you make a decision on the purchase.
If you already are a holder of NETGEAR NETGEAR, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime NETGEAR NETGEAR.
However, one of the most important roles played by the user manual is to help in solving problems with NETGEAR NETGEAR. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device NETGEAR NETGEAR along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
