Instruction/ maintenance manual of the product TPC-2012 National Instruments
Go to page of 47
TPC-2012 User Manual TPC-2012 User Manual July 2007 372052B-01.
Support Worldwide Technical Support and Product Info rmation ni.com National Instruments Corporate Headquarters 11500 North Mopac Expressway Aust in, Texas 78759-3504 USA Tel: 512 683 0100 Worldwide O.
Important Information Warranty The TPC-2012 is warranted agains t defects in materia ls and workma nship for a period of one year from the date of shipment, as e videnced by receipts or other documentation. National Instruments will, at its option, repair or replace equi pment that proves to be defect ive during the warranty period.
Compliance Compliance with FCC/Canada Radio Frequency Interference Regulations Determining FCC Class The Federal Communications Commission (FCC) has rules to protect wireless co mmunications from inte rference. The FCC places digital electronics into two classes.
Conventions The follo wing con ventions are used in this manual: » The » symbol leads you through nested menu items and dialog box options to a final action. The sequence File»Page Setup»Options directs yo u to pull down the File menu, select the Page Setup item, and select Options from the last dialog box.
© National Instruments Corporatio n vii TPC-2012 User Manual Contents Chapter 1 General Information Introduction ........................ .............. .............. .............. ............... .............. .............. ...... .1 - 1 I/O Ports .
Contents TPC-2012 User Manual viii ni.com Appendix F Touchscreen Configuration Appendix G Fuse Replacement Appendix H Technical Support and Professional Services Index.
© National Instruments Corporatio n 1-1 TPC-2012 User Manual 1 General Information This chapter includes general information about the TPC-2012 Human Machine Interface (HMI).
Chapter 1 General Information TPC-2012 User Manual 1-2 ni.com Figure 1-1 shows the I/O port arrangement. Figure 1-1. I/O Port Arrangement For more TPC-2012 specifications, see Appendix A, Specifications . Cleaning If you need to clean the unit, use a soft, nonm etallic brush.
© National Instruments Corporatio n 2-1 TPC-2012 User Manual 2 System Setup This chapter includes setup information for the TPC-2012. Important Safety Information Before setting up the TPC-20 12, read these safety instructions carefu lly. Disconnect this equipment from an y A C outlet before cleaning.
Chapter 2 System Setup TPC-2012 User Manual 2-2 ni.com If one of the following situations ar ises, ha ve service personnel check the equipment: • The power cord or plug is damaged. • Liquid has penetrated into the equipm ent. • The equipment has been exposed to moisture.
Chapter 2 System Setup © National Instruments Corporatio n 2-3 TPC-2012 User Manual Caution Be sure system power is off before plugging in or pulling ou t the CompactFl ash card. 2. Install a CompactFlash card containing W indo ws CE, embedded W indo ws XP , or another operating syst em.
Chapter 2 System Setup TPC-2012 User Manual 2-4 ni.com Panel Mounting Follow these steps to mount th e TPC-2012 in a panel: 1. Be sure the adhesi ve waterproof gasket on the front bezel is in position. 2. Install the TPC-20 12 in the p ane l opening. (Refer to Appendix A, Specifications , for cuto ut dimensions.
© National Instruments Corporatio n 3-1 TPC-2012 User Manual 3 Jumpers and Connectors This chapter describes the TPC-2012 jumpers and connectors. Jumper and Connector Functions Table 3-1 lists the jumper and connector functions.
Chapter 3 Jumpers and Conn ectors TPC-2012 User Manual 3-2 ni.com JP1 Panel P anel connector JP2 To u c h T o uch connector JP4 5 V/3 V PCI104 5 V/3 V select J1 DDR DDR connector J3 1*3 pin header Clear CMOS SW1 Power switch System power switch BH1 Battery R T C battery FS1 Fuse Fuse holder Table 3-1.
Chapter 3 Jumpers and Connectors © National Instruments Corporatio n 3-3 TPC-2012 User Manual Jumper and Connector Locations Figures 3-1 and 3-2 show the ju mper and connector locations.
Chapter 3 Jumpers and Conn ectors TPC-2012 User Manual 3-4 ni.com Figure 3-2. Main Board Jumpers and Connectors.
© National Instruments Corporatio n A -1 TPC-20 12 User Manual A Specifications This appendix lists the TPC- 2012 system specifications. Physical Weight ......... ................. .............. ............ 4.1 kg (without HDD) Cutout dimensions...
Appendix A Specifications TPC-2012 User Manu al A- 2 ni.com Dimensions 11 [0.433] 7 [0.079] 237 [9.331] 311 [12.244] 301.49 [11.869] 227.49 [8.956] 2.5 [0.
Appendix A Specifications © National Instruments Corporatio n A -3 TPC-20 12 User Manual System Kernel CPU ....... .............. ................. .............. .... GeodeLink Control Processor LX800 500 MHz BIOS................. ............... ..
Appendix A Specifications TPC-2012 User Manu al A- 4 ni.com Backlight ......... .............. .............. ............2 CCFL Backlight lifespan ............... ................ ....50,000 h Note There may be several bright or dark pixels on the LCD.
Appendix A Specifications © National Instruments Corporatio n A -5 TPC-20 12 User Manual Vibration ................... .............. .............. . 1 grms (5 to 500 Hz) Maximum altitude ...................... ............ 2,000 m Pollution Degree .
Appendix A Specifications TPC-2012 User Manu al A- 6 ni.com Environmental Management National Instruments i s committed to designing and manu facturing products in an environmental ly responsible mann er.
© National Instruments Corporatio n B -1 TPC-20 12 User Manual B Serial Port Settings This appendix describes the TPC-2012 serial port settings. COM1/COM2/COM3 Connector Pinout The follo wing fi gure and t able sh o w the COM1/COM2/COM3 connector pinout.
Appendix B Serial Port Settings TPC-2012 User Manu al B- 2 ni.com COM4 Connector Pinout and Settings The TPC-2012 COM4 serial port is adjustable. Y ou can set it to RS-232, RS-422, or RS-485, and it has auto data flow control capability .
Appendix B Seria l Port Settings © National Instruments Corporatio n B -3 TPC-20 12 User Manual PIN RS-232 RS-422 RS-485 1 NDCD TX– D– 2 NRX TX+ D+ 3 NTX RX+ 4 NDTR RX– 5 GND GND GND 6 NDSR 7 N.
© National Instruments Corporatio n C -1 TPC-20 12 User Manual C W atchdog T imer Programming This appendix explains the TPC-2012 watchdog timer programming. Over view Y ou can use the TPC-2012 watchdog timer to mo nitor system software operation and ta ke correctiv e action if the software fails to function after the programmed period.
Appendix C W atchdog T imer Programming TPC-2012 User Manu al C- 2 ni.com Figure C-1 describes the watchdog timer program ming procedure, and T ab le C-1 describes the watchdog timer registers.
Appendix C W atchdog T imer Programmin g © National Instruments Corporatio n C -3 TPC-20 12 User Manual Table C-1. Watchdog T imer Registers Address of Register (2E) Attribute Description Read/Write V alue (2F) and descriptio n — 87 (hex) — Write this ad dress twice to I/O address port 2E (hex) to unlock the W83627HF .
Appendix C W atchdog T imer Programming TPC-2012 User Manu al C- 4 ni.com Example Programs Example 1: Enable the W atchdog T imer and Set 10 s as the T imeout Inter val ;------------------------------.
Appendix C W atchdog T imer Programmin g © National Instruments Corporatio n C -5 TPC-20 12 User Manual Example 2: Enable the W atchdog T imer and Set 5 Min as the T imeout Inter val ;---------------.
Appendix C W atchdog T imer Programming TPC-2012 User Manu al C- 6 ni.com Example 3: Enable the Mouse to Reset the W atchdog T imer ;----------------------------------- ------------------------ Mov dx.
Appendix C W atchdog T imer Programmin g © National Instruments Corporatio n C -7 TPC-20 12 User Manual Example 4: Enable the Keyboard to Reset the W atchdog T imer ;---------------------------------.
Appendix C W atchdog T imer Programming TPC-2012 User Manu al C- 8 ni.com Example 5: Generate a T imeou t Signal without Timer Counting ;----------------------------------- ------------------------ Mo.
© National Instruments Corporatio n D-1 T PC-2012 User Manual D W atchdog T imer Programming on WinCE W indo ws CE includes a watchdog ti mer for the TPC-2012. Y ou can access the timer through t he WIN32 API. The TPC -2012 includes a W DT driv er , WDT1:, for enabling/disabling the watchdog tim er .
Appendix D W atchdog Timer Progr amming on WinCE TPC-2012 User Manual D-2 ni.com can use these control codes with De viceIoControl to perform dri ver -specific functions. • lpInBuffer (in) Long pointer to a buf fer that contains the data required to perform the operation.
Appendix D W atchdog T imer Programming on WinCE © National Instruments Corporatio n D-3 T PC-2012 User Manual How to Use the Control Codes There are six control codes for the WDT dri ver operation codes. IOCTL _WDT_ENABLE Enables the application watchdog timer .
Appendix D W atchdog Timer Progr amming on WinCE TPC-2012 User Manual D-4 ni.com • lpOutBuffer : The D WORD points to your watchdog time setting. The watchdog time settings are: • nOutBufferSize : unused IOCTL_WDT_SETTIMEOUT Sets the watchdog time setting.
Appendix D W atchdog T imer Programming on WinCE © National Instruments Corporatio n D-5 T PC-2012 User Manual IOCTL_WDT_REBOOT If you want your application to trigger the watchdog, use IOCTL_WDT_REBOOT to notify the watchdog driv er timer (WDT). Otherwise, the WDT trigg ers itself automatically .
Appendix D W atchdog Timer Progr amming on WinCE TPC-2012 User Manual D-6 ni.com While (1) { // do your job here. Sleep(8000); DeviceIoControl(m_hWDT, IOCTL_WDT_ST ROBE, NULL,0, NULL, 0, &dwTemp, .
© National Instruments Corporatio n E-1 TPC-2012 User Manual E Accessor y Kit Assembly Procedure This appendix explains ho w to connect to a CD-R OM via the CompactFlash slot. CompactFlash to IDE T ransfer Kit Assembly Follo w these steps to connect to a CD-R OM via the CompactFlash slot: 1.
© National Instruments Corporatio n F-1 TPC-2012 User Manual F T ouchscreen Configuration This appendix explains how to conf igure the TPC-2012 touchscreen using the PenMount Control Panel. T ouchscreen Calibration T o cali brate the TPC-2012, go to Start» Control Panel» Stylus , which displays the Stylus Properties screen.
© National Instruments Corporatio n G-1 T PC-2012 User Manual G Fuse Replacement Caution Do not replace the fuse unless it is damaged. Do not replace the fuse with a differently rated fuse. For more information, see the fuse specifications in Appendix A, Specifications .
© National Instruments Corporatio n H-1 T PC-2012 User Manual H T echnical Support and Professional Ser vices Visit the following sections of the National Instruments Web site at ni.com for technical support an d professional services: • Support —Online technical support resources at ni.
© National Instruments Corporatio n I-1 TPC-2012 User Manual Index A accessory kit assembly, E-1 C CE compliance specif ications, A-5 cleaning, 1-2, A-6 COM1/COM2/COM3 connector pinout , B-1 COM4 con.
Index TPC-2012 User Manu al I-2 ni.com K Kno wledgeBase, H-1 L LCD specifications, A-3 M mercury disposal and recycling specifications, A-6 N National Instruments support and services, H-1 P panel mou.
Index © National Instruments Corporatio n I-3 TPC-2012 User Manual I/O ports, 1-1 introduction, 1-1 jumpers, 3-1 LCD specifi cations, A-3 mercury disposal and recycling specifications, A-6 panel moun.
An important point after buying a device National Instruments TPC-2012 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought National Instruments TPC-2012 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data National Instruments TPC-2012 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, National Instruments TPC-2012 you will learn all the available features of the product, as well as information on its operation. The information that you get National Instruments TPC-2012 will certainly help you make a decision on the purchase.
If you already are a holder of National Instruments TPC-2012, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime National Instruments TPC-2012.
However, one of the most important roles played by the user manual is to help in solving problems with National Instruments TPC-2012. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device National Instruments TPC-2012 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
