Instruction/ maintenance manual of the product XP-400 Napco Security Technologies
Go to page of 16
Usin g Y our XP-400 Security Sy stem NAPCO Oi220a page 1 Tuesday, September 16, 1997 08:30.
2 Oi220a page 2 Tuesday, September 16, 1997 08:30.
Introduction Congratulations on y our purc hase of an advanced NAPCO EXPRESS XP- 400 Security Sy stem. Meticulous ly developed by a leading manufac turer of state- of-the-art s ecurity products, this s y stem w ill provide y ou w ith unprecedented peace-of- mind & incorporates some of the most s ophisticated features available today .
4 1 Bell / Battery Test Test y our bell or siren by pressing followed by . This will caus e the bell, or siren to sound f or 2 seconds and also initiate a test of the battery . 2 Central Station Communication Test (This test should only be perform ed on weekends or at a time designated by y our alarm com pany) 1.
Key pad Controls and Indi cator s Ready Light will light when all z ones are sec ure and system is r eady to be Armed. Zone Lights ( 1 through 4) will light to indicate that the corres ponding Zone is open, and will flash to indic ate a z one in alarm .
A rming Your Sy stem When Leaving 1 Before arm in g y our system, m ak e sure the Green Ready li g ht is ON. T his indicates that all of y our prot- ective zones are secur e. If any zones are open, the corres pondin g Zone li g ht will be ON. Secure these zones before proceedin g .
Protecting Yourself While at Home 1 Before ar min g y our system, m ak e sure the Green Ready li g ht is ON. T his indicates that all of y our protective zones are sec ure. If any z ones are open, the corr espondin g Zone li g ht will be ON. Secure those zones before proc eedin g .
Emergency Buttons The two s ets of em ergency buttons, if pr ogramm ed, are always active whether the system is armed or disarm ed. Discuss these buttons with y our installer. The em ergency signal will only be activated when the two respective buttons ar e pressed at the sam e time.
Disarming Your Sy stem when Returning 1 Enter y our prem ises throu g h the Entry/Exit door. The k ey pad will sound a steady tone to rem ind y ou to disarm the system befor e y our Entry Delay tim e expires. 2 Enter y our user code. T he Red Ar m ed li g ht will g o out, indicatin g that the system has been dis armed.
Special Functions By pressing follow ed by the appropriate key , (do not press simultaneously) these special functions and features can be enabled: Easy A rm ( w hen sy stem is disarm ed) The Easy Arm feature allows the system to be arm ed by pressing f ollowed by .
Your Installer has ass igned a User 1 Code which may be used to not only Arm and Disarm the system, but also to enter the User Program Mode, where y ou can program and/or reprogram up to 4 User Codes. The following explains how you w ill use this c ode to program or erase additional user codes .
The X P400 is constantly monitoring its own com ponents, as well as all c ritical services , such as AC Power and the Telephone line, to insure that it is alway s ready to provide the protection for which it was designed. W hen a sy stem trouble does occ ur, it will caution you by lighting the Yellow SYST EM light and beeping the keypad buzz er.
13 9 Sy stem Tr oubl es Keypad Beeps or SYSTEM Flashes Zone light ON System Tr ouble Condition Action 2 Beeps 1 Bell / Siren Trouble There is a problem w ith the Bell or Siren. Call installing com- pany for service. 2 Beeps 3 W ireless Receiv er Trouble A problem has been detected w ith the wireless receiv er.
A mbush Code - In the event that y ou are for ced by an intruder to dis- arm y our system, this special code can be used to disarm the system, and sim ultane ously s end a s ilent alarm to Central Station.
15 Notes Oi220a page 15 Tuesday, September 16, 1997 08:30.
NA PCO LIM I TED WA RRANTY THE FOLL OW ING STATEM ENT I S REQUIRED BY THE FCC . This equipment generates and uses radio-frequency energy and, if not installed and used properly, that is, in strict accordance with the m anufacturer's instructions, may cause interference to radio and television reception.
An important point after buying a device Napco Security Technologies XP-400 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Napco Security Technologies XP-400 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Napco Security Technologies XP-400 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Napco Security Technologies XP-400 you will learn all the available features of the product, as well as information on its operation. The information that you get Napco Security Technologies XP-400 will certainly help you make a decision on the purchase.
If you already are a holder of Napco Security Technologies XP-400, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Napco Security Technologies XP-400.
However, one of the most important roles played by the user manual is to help in solving problems with Napco Security Technologies XP-400. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Napco Security Technologies XP-400 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
