Instruction/ maintenance manual of the product UHF24HT1112 Nady Systems
Go to page of 8
NAD Y SY STEMS, INC. 6701 Shellmound Street • Emeryville, CA 94608 T el: 510.652.241 1 • Fax: 510.652.5075 • www .nady .com SERVICE INFORMA TION (U.S.) If you are experiencing operation problem with your system, check out the support page on the Nady website: www .
1 5 SPECIFICA TIONS OVERALL SYSTEM SPECIFICA TIONS Frequency Response ............................................................................................. 20Hz-20kHz, -3dB Dynamic Range ........................................................
1 4 • The receiver antennas should be kept away from any metal surface. • If the V olume Control of the receiver is set too high, it may over-drive the input of the mixer , caus- ing distortion. Conversely , if the output is set too low , the overall signal to noise ratio of the system may be reduced.
4 UHF-24 RECEIVER Rack-mounting the Receiver There are two options available for rackmounting the UHF-24 Dual Channel Receiver: single or side-by-side with another UHF-24 receiver . a. Single mounting: Remove the SIDE MOUNT CLIPS (1) from each side of the receiver and slide in the optional ERM-3 RACK EARS (2) .
12 Receiver V olume Controls Adjust The volume controls work only for the 1⁄4” sum output. T urn V olume controls on the UHF-24 receiver clockwise to near full gain. Adjust V olume up or down so that no audio distortion is present when amplifi er or mixer is set at their usual levels.
internal T one Squelch defeat feature. Contact your Nady dealer or Nady Systems Customer Service for details.) Note: • Even though your system has T one Squelch™, it’s always best to keep the volume controls of unused channels, (with corresponding transmitter off) turned off in the amplifi er or the mixer .
7 UH-4 HANDHELD TRANSMITTER T ransmitters set up The UH-4 transmitter requires a single 9V battery to operate. T o open the battery compartment, unscrew the BA TTERY COVER (16) with a counter-clockwise turn and remove the cover , exposing the BA TTERY HOLDER (17) .
9 UB-4 BOD YP ACK TRANSMITTER The UB-4 is equipped with two INPUT SELECTOR SWITCHES (27) located under the cover on the circuit board for selecting the type of audio input you will be supplying to the transmitter . Select from the choice of three positions: INSTRUMENT (for guitar , bass, etc.
An important point after buying a device Nady Systems UHF24HT1112 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Nady Systems UHF24HT1112 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Nady Systems UHF24HT1112 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Nady Systems UHF24HT1112 you will learn all the available features of the product, as well as information on its operation. The information that you get Nady Systems UHF24HT1112 will certainly help you make a decision on the purchase.
If you already are a holder of Nady Systems UHF24HT1112, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Nady Systems UHF24HT1112.
However, one of the most important roles played by the user manual is to help in solving problems with Nady Systems UHF24HT1112. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Nady Systems UHF24HT1112 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
