Instruction/ maintenance manual of the product MC3PBA (B&S) Multiquip
Go to page of 46
OPERA TION AND P AR TS MANUAL THIS MANU AL MUST A CCOMP ANY THE EQUIPMENT A T ALL TIMES. MIX N' GO MODELS MC3SEA, MC3SBA (B&S) MINI CONCRETE STEEL DRUM MIXERS MODELS MC3PEA, MC3PBA (B&S) .
P A GE 2 —MIX N' GO MIXER — OPERA TION AND P ARTS MANU AL — REV . #3 (09/20/11) Engine exhaust and some of its constituents, and some dust created of California to cause cancer , birth defects and other repr oductive harm.
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 3 Grinding/cutting/drilling of masonry , concrete, metal and other materials with silica in their composition may give off dust or mists containing crystalline silica.
P A GE 4 —MIX N' GO MIXER — OPERA TION AND P ARTS MANU AL — REV . #3 (09/20/11) T ABLE OF CONTENTS Multiquip Mix N' Go — Portable Concrete Mixer Proposition 65 W ar ning ............................................. 2 Silicosis/Respir ator y W arnings .
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 5 P AR TS ORDERING PROCEDURES www .multiquip .com Or dering par ts has never been easier! Choose fr om three easy op.
P A GE 6 —MIX N' GO MIXER — OPERA TION AND P ARTS MANU AL — REV . #3 (09/20/11) SAFETY INFORMA TION Do not operate or service the equipment before reading the entire manual. Saf ety precautions should be follo wed at all times when operating this equipment.
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 7 GENERAL SAFETY CA UTION NEVER operate this equipment without proper protectiv e clothing, shatter proof glasses, respiratory protection, hearing protection, steel-toed boots and other protective de vices required b y the job or city and state regulations.
P A GE 8 —MIX N' GO MIXER — OPERA TION AND P ARTS MANU AL — REV . #3 (09/20/11) SAFETY INFORMA TION MIXER SAFETY D ANGER NEVER operate the equipment in an e xplosiv e atmosphere or near combustib le mater ials. An e xplosion or fire could result causing se vere bodily harm or e ven death.
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 9 SAFETY INFORMA TION FUEL SAFETY (GASOLINE MODELS ONL Y) D ANGER DO NO T add fuel to equipment if it is placed inside truck bed with plastic liner . P ossibility e xists of e xplosion or fire due to static electricity .
P A GE 10 —MIX N' GO MIXER — OPERA TION AND P AR TS MANU AL — REV . #3 (09/20/11) SAFETY INFORMA TION TRANSPOR TING SAFETY CA UTION NEVER allo w any person or animal to stand underneath the equipment while lifting.
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 11 OPERA TION AND SAFETY DECALS Machine Safety Decals The Mix N' Go mix er is equipped with a number of saf ety decals . These decals are pro vided f or operator saf ety and maintenance inf ormation.
P A GE 12 —MIX N' GO MIXER — OPERA TION AND P AR TS MANU AL — REV . #3 (09/20/11) OPERA TION AND SAFETY DECALS 6. check V-belt before starting mixer . AL W A YS 1. Read owner’s manual before operating mixer. ELECTRIC MOTOR Make sure power cord has been disconnected from power source before cleaning mixer .
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 13 MIX N' GO MIXER — SPECIFICA TIONS s n o i t a c i f i c e p S r e x i M o G ' N x i M . 2 e l b a T t h g i e H ) m m 6 . 3 6 8 ( . n i 4 3 h t d i W ) m m 2 .
P A GE 14 —MIX N' GO MIXER — OPERA TION AND P AR TS MANU AL — REV . #3 (09/20/11) MIX N' GO MIXER — DIMENSIONS (MIXER) Figure 1. Mix N' Go Mixer Dimensions.
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 15 MIX N' GO MIXER — DIMENSIONS (ELECTRIC MO T OR) Figure 2.
P A GE 16 —MIX N' GO MIXER — OPERA TION AND P AR TS MANU AL — REV . #3 (09/20/11) MIX N' GO MIXER — GENERAL INFORMA TION APPLICA TION This mixer is only intended for the production of concrete and mor tar . The mix er m ust be used for its intended purposes and is not suitable for the mixing of flammable or explosive substances .
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 17 MIX N' GO MIXER — MIXER COMPONENTS Figure 4. Mixer Components Figure 4 shows the basic components of the Mix N' Go Mixer .
P A GE 18 —MIX N' GO MIXER — OPERA TION AND P AR TS MANU AL — REV . #3 (09/20/11) Figure 5. Engine Controls and Components INITIAL SER VICING The engine (Figure 5) must be checked for proper lubrication and filled with fuel prior to operation.
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 19 MIX N' GO MIXER — ASSEMBL Y INSTR UCTIONS Assembly 1 . Remove the mixer drum and associated components from the packing container (Figure 6). Match the components against the parts list to make sure that they are all accounted fo r.
P A GE 20 —MIX N' GO MIXER — OPERA TION AND P AR TS MANU AL — REV . #3 (09/20/11) 6 . Tip mixer onto mouth as shown in Figure 10, and insert support stand into frame swivel point. 9 . Bef ore attempting to lift mixer , locate the fr ame locking clip .
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 21 MIX N' GO MIXER — PRE-INSPECTION (GASOLINE ENGINE) Figure 15. Engine Oil Dipstick (Removal) 3 . Insert and remove the dipstick without screwing it into the filler neck.
P A GE 22 —MIX N' GO MIXER — OPERA TION AND P AR TS MANU AL — REV . #3 (09/20/11) MIX N' GO MIXER — INITIAL ST AR T -UP (ELECTRIC MO TOR) CAUTION: CAUTION: CAUTION: CAUTION: CAUTION: DO NOT attempt to operate the mixer until the Saf ety , General Inf or mation and Inspection sections have been read and understood.
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 23 MIX N' GO MIXER — INITIAL ST AR T -UP (GASOLINE ENGINE) Star ting the Engine ( BRIGGS & STRA TT ON ) 1 . Place the choke lever (Figure 21) in the CHOKE (CLOSED) position if starting a cold engine.
P A GE 24 —MIX N' GO MIXER — OPERA TION AND P AR TS MANU AL — REV . #3 (09/20/11) MIX N' GO MIXER — INITIAL ST AR T -UP (GASOLINE ENGINE) Figure 26. Throttle Le ver (Idle P osition) 2 . After the engine cools , move the throttle le ver to the STOP position (Figure 27).
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 25 MIX N' GO MIXER — MAINTENANCE Maintenance Gearbox Oil Check 1. P osition the mix er on a lev el surf ace and place a suppor t bloc k under the front of the mix er frame as sho wn in Figure 29.
P A GE 26 —MIX N' GO MIXER — OPERA TION AND P AR TS MANU AL — REV . #3 (09/20/11) MIX N' GO MIXER — MAINTENANCE (GASOLINE ENGINE) Reference manufacturer engine manual for specific servicing instructions. NOTE e l u d e h c S e c n a n e t n i a M e n i g n E .
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 27 Maintenance P erf or m the scheduled maintenance procedures as definded by T able 6 and below: D AIL Y ■ Thoroughly remove dirt and oil from the engine and control area.
P A GE 28 —MIX N' GO MIXER — OPERA TION AND P AR TS MANU AL — REV . #3 (09/20/11) MIX N' GO MIXER — PREP ARA TION FOR LONG -TERM ST ORA GE Mixer Storage For storage of the mixer for over 30 days, the following is recommended: Drain the fuel tank completely , or add ST A-BIL to the fuel.
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 29 NO TE P A GE.
P A GE 30 —MIX N' GO MIXER — OPERA TION AND P AR TS MANU AL — REV . #3 (09/20/11) MIX N' GO MIXER — TR OUBLESHOO TING (ENGINE) G N I T O O H S E L B U O R T E N I G N E .
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 31 MIX N' GO MIXER — TR OUBLESHOO TING (ENGINE/MIXER) G N I T O O H S E L B U O R T R E X I M . 8 E L B A T M O T P M Y S M E L B O R P E L B I S S O P N O I T U L O S .
P A GE 32 —MIX N' GO MIXER — OPERA TION AND P AR TS MANU AL — REV . #3 (09/20/11) MIX N' GO MIXER — EXPLANA TION OF CODE IN REMARKS COLUMN The f ollo wing section e xplains the diff erent symbols and remarks used in the P ar ts section of this manual.
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 33 MIX N' GO MIXER — SUGGESTED SP ARE P A R TS MIX N' GO MIXER 1 T O 3 UNITS 1 to 3 Units Qt y . P / N Description 2 ............ DM1840 ................ V -BEL T , A23 (ELECTRIC MOT OR) 2 .
P A GE 34 —MIX N' GO MIXER — OPERA TION AND P AR TS MANU AL — REV . #3 (09/20/11) MIX N' GO MIXER — NAME PLA TE AND DECALS NAME PLA TE AND DECALS WA R N IN G ! A L A R M A ! AV E R T.
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 35 MIX N' GO MIXER — NAME PLA TE AND DECALS NAME PLA TE AND DECALS NAMEPLA TE AND DECALS. NO P AR T NO P AR T NAME QTY . REMARKS 1 * DCL251 DECAL: W ARNING MQ 1 2 * 510165 DECAL: MQ MIX N GO 1 3 DECAL: NAMEPLA TE .
P A GE 36 —MIX N' GO MIXER — OPERA TION AND P AR TS MANU AL — REV . #3 (09/20/11) MIXER ASSY . (STEEL DR UM) MIX N' GO MIXER — MIXER ASSY .
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 37 MIX N' GO MIXER — MIXER ASSY . (STEEL DR UM) MIXER ASSY . (STEEL DR UM) NO . P AR T NO . P AR T NAME QTY . REMARKS 1# DM3150 HEX HEAD BOL T M12 x 70 1 2# DM1356 OIL FILLER PLUG M14 x 2 x 15L 1 3# DM1912 HEX NUT M10 2 4# DM355 HEX HEAD BOL T M8 x P1.
P A GE 38 —MIX N' GO MIXER — OPERA TION AND P AR TS MANU AL — REV . #3 (09/20/11) MIX N' GO MIXER — MIXER ASSY . (STEEL DR UM) MIXER ASSY .
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 39 MIXER ASSY . (STEEL DR UM) NO . P AR T NO . P AR T NAME QTY . REMARKS 31 DM1527 HEX NUT M10 2 32 DM1524 B O L T 2 33 DM1400 STEEL BARREL 1 34 DM1414 BLADE, STEEL BARREL 2 35 @ DM1613 HANDLE GRIP , R UBBER 2 36 @ DM1630 TOP C O VER CLAMP 2 37 @ DM1631 SCREW 5.
P A GE 40 —MIX N' GO MIXER — OPERA TION AND P AR TS MANU AL — REV . #3 (09/20/11) MIXER ASSY . (PLASTIC DR UM) MIX N' GO MIXER — MIXER ASSY .
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 41 MIX N' GO MIXER — MIXER ASSY . (PLASTIC DR UM) MIXER ASSY . (PLASTIC DR UM) NO . P AR T NO . P AR T NAME QTY . REMARKS 1# DM3150 HEX HEAD BOL T M12 x 70 1 2# DM1356 OIL FILLER PLUG M14 x 2 x 15L 1 3# DM1912 HEX NUT M10 2 4# DM355 HEX HEAD BOL T M8 x P1.
P A GE 42 —MIX N' GO MIXER — OPERA TION AND P AR TS MANU AL — REV . #3 (09/20/11) MIX N' GO MIXER — MIXER ASSY . (PLASTIC DR UM) MIXER ASSY .
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 43 MIXER ASSY . (PLASTIC DR UM) NO . P AR T NO . P AR T NAME QTY . REMARKS 31 DM1527 HEX NUT M10 1 2 32 DM1524 BOL T 12 33 DM1510 PLASTIC BARREL 1 34 DM1531 BLADE, BARREL 2 35 @ DM1613 HANDLE GRIP , R UBBER 2 36 @ DM1630 TOP C O VER CLAMP 2 37 @ DM1631 SCREW 5.
P A GE 44 —MIX N' GO MIXER — OPERA TION AND P AR TS MANU AL — REV . #3 (09/20/11) TERMS AND CONDITIONS OF SALE — P AR TS P A YMENT TERM S T erms of payment for parts are net 3 0 days. FREIGHT P OLIC Y All parts orders will be shipped collect or prepaid with the c harges ad ded to the invoice.
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 45 NO TES.
Y our Local Dealer is: HERE’S HOW TO GET HELP PLEASE HA VE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING UNITED ST A TES Multiquip Corporate Offi ce MQ P arts Depar tment 18910 Wilmington A v e.
An important point after buying a device Multiquip MC3PBA (B&S) (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Multiquip MC3PBA (B&S) yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Multiquip MC3PBA (B&S) - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Multiquip MC3PBA (B&S) you will learn all the available features of the product, as well as information on its operation. The information that you get Multiquip MC3PBA (B&S) will certainly help you make a decision on the purchase.
If you already are a holder of Multiquip MC3PBA (B&S), but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Multiquip MC3PBA (B&S).
However, one of the most important roles played by the user manual is to help in solving problems with Multiquip MC3PBA (B&S). Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Multiquip MC3PBA (B&S) along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
