Instruction/ maintenance manual of the product HTXD6i / STXD6i Multiquip
Go to page of 32
SETUP , ADJUSTMENTS AND CALIBRA TIONS THIS MANU AL MUST A CCOMP ANY THE EQ UIPMENT A T ALL TIMES. T o find the latest re vision of this publication, visit our website at: www .
P A GE 2 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) T ABLE OF CONTENTS HTX6Di/STX6Di T r owel Machine Inf ormation And Maintenance Log ............ 3 Saf ety Inf ormation ...............................
HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 3 MACHINE INFORMA TION AND MAINTENANCE LOG T echnician__________________________________ e Date:___________________________ Machine Inf ormation MODEL LH Motor Serial No.
P A GE 4 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) Do not operate or service the equipment before reading the entire manual. Saf ety precautions should be f ollow ed at all times when operating this equipment.
HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 5 GENERAL SAFETY CA UTION NEVER operate this equipment without proper protectiv e clothing, shatt.
P A GE 6 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) TRO WEL SAFETY D ANGER Engine fuel e xhaust gases contain poisonous carbon mono xide. This gas is colorless and odor less, and can cause death if inhaled.
HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 7 NO TICE NEVER run engine without an air fi lter or with a dir ty air fi lter . Sev ere engine damage may occur . Ser vice air fi lter frequently to pre v ent engine malfunction.
P A GE 8 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) TRANSPORTING SAFETY CA UTION NEVER allow an y person or animal to stand underneath the equipment while lifting. Ride-on trowels are v er y heavy and awkw ard to mov e around.
HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 9 T railer should be adjusted to a le v el position at all times when towing. Raise and lock tr ailer wheel stand in up position when towing. Place choc k blocks underneath wheel to prev ent rolling while parked.
P A GE 10 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) TOOLS NEEDED The specialized tools listed in T able 1 are required to maintain and service the HTXD6i and STXD6i r ide-on trow els.
HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 11 MACHINE INFORMA TION MODEL 1 . Enter appropriate model: HTXD6i — f or 6-blade HTX STXD6i — f or 6-blade STX SERIAL NUMBER 2 . Mac hine Serial Number — as shown on serial tag.
P A GE 12 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) GENERAL PROCEDURES SETUP JUMPER INST ALLA TION 1 . Remo v e Cap (PN: 22812) on P24 of main har ness (under f oot platf orm). 2 . Install Setup J umper (P/N: 32007 on P24).
HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 13 INITIAL CHECK AND ADJUSTMENTS PRELIMINAR Y CHARGE PRESSURE ADJUSTMENT 1 . Loosen 1-1/16" jam n ut on charge relief v alve (Item A, Figure 5). 2 .
P A GE 14 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) Engine Oil 1 . Ensure engine is le vel. 2 . Remo v e the oil filler cap (top or side). See Figure 7. Figure 7. Adding Engine Oil 3 . Add the required amount of engine oil at the top or side engine oil filler por t.
HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 15 SER VICE TOOL SETUP AND CONNECTION WHITEMAN SER VICE TOOL (WST) INST ALLA TION 1 . Call or e-mail Multiquip T echnical Suppor t or Field Ser vice to obtain the application specific Whiteman Ser vice T ool (WST) file.
P A GE 16 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) 9 . The ne w screen will ha v e both na vigation and tool bars active (Figure 13.) Figure 13. WST T ool Bar 10. Click on "T ools". On the drop-down men u, clic k on "License Manager" (Figure 14).
HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 17 LAPTOP CONFIGURA TION CONNECTION PROCEDURE 1 . Plug the CAN Gate wa y cable to the trow el at the ser vice por t (Figure 16). Do not connect laptop at this time.
P A GE 18 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) MACHINE SETUP AND CALIBRA TION CALIBRA TE FOOT PED AL 1 . T ur n key to ON position b ut DO NOT star t machine. 2 . Clic k “CALIBRA TION” button on machine setup page.
HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 19 MACHINE SETUP AND CALIBRA TION Calibration 1 . Set sensor z ero position def ault: a . Ensure that f oot pedal is fully released. b. Read % SENSOR V OL T A GE.
P A GE 20 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) MA CHINE PRESSURE ADJUSTMENT Charge Pressure Adjustment 1 . Disab le cold star t. 2 . With machine off , install gauge capable of reading 300 psi to Charge Or Pitch pressure test por t (Figure 27).
HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 21 MACHINE SETUP AND CALIBRA TION 8 . Return engine r pm to idle. 9 . T ur n off machine and remove gauge . Pitch Pressure Adjustment 1 . Disab le cold star t.
P A GE 22 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) 8 . Retighten jam n ut. 9 . Return engine to idle. 10. T urn off machine and remove gauge . 11. Record Pressure on Machine Information and Maintenance Log.
HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 23 MACHINE SETUP AND CALIBRA TION 5 . Re-measure speed, repeating steps 2 and 3 until Left Side T rowel Speed is correct: a . HTXD6i — 157 to 160 RPM (942 to 960 Pulses per minute) b.
P A GE 24 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) 6 . Set Sensor z ero position def ault: a . Ensure f oot pedal is fully released. b. Read % Sensor V oltage (Figure 35). Figure 35. Star t Stroke Sensor Calibration c .
HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 25 MACHINE SETUP AND CALIBRA TION Measure Blade Leading Edge Height 1 . Fully pitch machine b y pressing and holding T win pitch up button until pitch cylinders fully e xtended.
P A GE 26 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) Set Zero Pitc h Cylinder Stops 1 . Flatten b lades (bottom out the pitch cylinders). 2 . T ur n machine off. 3 . Remo v e cle vis pin (Item E, Figure 39) from pitch cylinder allowing y oke (Item B, Figure 39) to rest on thrust collar .
HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 27 b. Install 3.25” Gauge (P/N 32044) o v er both Left and Right Cylinders as shown in Figure 41. Figure 41. Gaug e Installation c . Press Hard Ret. button to retract cylinder onto gauge.
P A GE 28 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) INSPECTION FLUID LEVELS Record the f ollowing fluid le vels on Machine Inf ormation and Maintenance Log in Inspection section. Refer to Fluid Fill and Check section f or procedure.
HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 29 ST A TIC BLADE PITCH DRIFT TEST 1 . Switch smart pitch switch to off position. 2 . Bring machine up to temperature. This will be indicated by “Cold Star t” (aux 1) lamp tur ning off.
P A GE 30 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) FUSE INFORMA TION T able 3. Fuses Fuse Number Amps Designator Functions Fused 1 20 T13 MCU P ow er T21 Service Port Connector 2 20 T3 Oil Cooler 3 5 T5 Light Switch T15 Pitch Switches 4 20 T6 Left Lights 5 7.
HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 31 NOTES.
SETUP , ADJUSTMENTS AND CALIBRA TIONS Y our Local Dealer is: HERE’S HOW TO GET HELP PLEASE HA VE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING United St a teS Multiquip Corporate Office MQ P arts Depar tment 18910 Wilmington A v e. Carson, CA 90746 Contact: mq@multiquip .
An important point after buying a device Multiquip HTXD6i / STXD6i (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Multiquip HTXD6i / STXD6i yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Multiquip HTXD6i / STXD6i - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Multiquip HTXD6i / STXD6i you will learn all the available features of the product, as well as information on its operation. The information that you get Multiquip HTXD6i / STXD6i will certainly help you make a decision on the purchase.
If you already are a holder of Multiquip HTXD6i / STXD6i, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Multiquip HTXD6i / STXD6i.
However, one of the most important roles played by the user manual is to help in solving problems with Multiquip HTXD6i / STXD6i. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Multiquip HTXD6i / STXD6i along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
