Instruction/ maintenance manual of the product G2150I Moxa Technologies
Go to page of 131
G2150I A T Command Set Second Edition, June 2007 www .moxa.com/product Moxa Technologies Co., Ltd. Tel: +886-2-8919-1230 Fax: +886-2-8919-1231 Web: www.
OnCell G2150I AT Command Set The software d escribed in t his manual is furnished u nder a license a greement and m ay be used only in accordance with the term s of that agreement. Copyright Notice Copyright © 2007 Moxa Technologies Co., Ltd. All rights reserved.
Table of Contents Chapter 1 Introduction .................................................................................................. 1-1 Scope of the Document .....................................................................................
Chapter 5 Network Service Commands ....................................................................... 5-1 Signal Qua lity: +C SQ .............................................................................................................. 5-2 Operator Selec tion: +COPS .
Select Data Error Correcting Mode: N ................................................................................... 8-7 Chapter 9 V24-V25 Commands ..................................................................................... 9-1 Fixed DTE Ra te: +IPR .
Failure Cause from GSM 04 .08 Recomm enda tion: +CEER................................................... A-4 Specific Failure Cause for +CEER ......................................................................................... A-6 GSM 04.1 1 Annex E-2: Mobile Originating SM-T ransfer.
1 1 Chapter 1 Introduction This chapter is an introductio n to the OnCell G 2150I AT Command Set. The follow ing topics are covered: Scope of the Document Related Documents ETSI Secretaria.
OnCell G2150I AT Command Set Introduction 1-2 Scope of the Document This docum ent describes the AT-comm and based messages exchange d between an a pplication a nd the OnCell G2150I for managing GSM related events or services.
OnCell G2150I AT Command Set Introduction 1-3 Abbreviations ADN Abbreviate d Dialing N umber (P honebook) AMR Adaptive Multi-Rate AMR-FR AMR Full Rate (full rate speech Version3) AMR-HR AMR Half Rate .
OnCell G2150I AT Command Set Introduction 1-4 Definitions The words “Mobile Station” (MS) or “Mobile Equipment” (ME) are used for mobile terminals that support GSM services. Term inal Equipment (TE) is the Human Machine Interface (HMI) of a GSM device ( modem or handset).
2 2 Chapter 2 AT Command Features This chapter inclu des information about the AT Comman d Features of the OnCell G2150I . The following topics are covered in this chap ter: Serial Line Settings .
OnCell G2150I AT Command Set AT Command Features 2-2 Serial Line Settings A serial li nk handle r is config ured with t he following default values (factory settings): y 115200 bps y 8 data bits y 1 stop bit y no parit y y RTS/CTS flow control Use the +IPR, +IFC, and + ICF commands to change t hese settings.
3 3 Chapter 3 General Commands This chapter includ es in formation about the General Comman ds of the OnCell G2150I. The following topics are covered in this chap ter: Manufacturer Identification:.
OnCell G2150I AT Command Set General Commands 3-2 Manufacturer Identification: +CGMI Description: This c ommand give s the m anufacturer ide ntification.
OnCell G2150I AT Command Set General Commands 3-3 Request Revision Identification: +CGMR Description: This comm and is used t o get the revised softw are version. T his functio n only appl ies to default IP addresses. Command syntax: AT+CGMR Command Possible responses AT + C G M R Note: Get softwar e version 657_09gg.
OnCell G2150I AT Command Set General Commands 3-4 Phonebook Character Set: +WPCS Description: This specific command in forms the ME which character set is used by the TE for the phonebooks. The ME can convert each char acter of en tered or displayed st rings.
OnCell G2150I AT Command Set General Commands 3-5 A T+CCID= ? Note: Get possible value OK Note: No parameter but this command is valid Note: if there is no EF-CCID file present on th e SIM, the +CCID answer will no t be sent, but the OK message will be returned.
OnCell G2150I AT Command Set General Commands 3-6 AT+CPO F). This co mmand ex ecutes an I MSI DETA CH an d makes a backup cop y of some internal parameters in SIM a nd in EEPROM.
OnCell G2150I AT Command Set General Commands 3-7 Report Mobile Equipment Errors: +CMEE Description: This comma nd disables or ena bles the use of the “+CME ERROR: <xxx>“ or “+CMS ERROR:<xxx>“ result code instead of simply “ERROR”.
OnCell G2150I AT Command Set General Commands 3-8 A T+CCLK? Note: Get curr ent date and time +CCLK: “00 /06/09, 17:34:23” OK Note: current date is June 9 th , 2000 current time is 5:34:23 pm Defined values: <date and time string> String format for date/time is: “yy/MM/dd, hh :mm:ss”.
OnCell G2150I AT Command Set General Commands 3-9 Command Possible responses A T+CSIM= <l ength>,<command> +CSIM : <length>,<resp onse> +CME ERROR : <err> AT + C S I M ? .
OnCell G2150I AT Command Set General Commands 3-10 “9408”. By using the A T+CSIM comm and, the “READ RE CORD” and “SEEK” actions retu rn 4,”9408” instead of CME ERROR:13.
OnCell G2150I AT Command Set General Commands 3-11 to GSM 11.11 or 3GPP TS 51.011). After th e READ BINARY or READ RECORD command, the requested data will be returned.
OnCell G2150I AT Command Set General Commands 3-12 AT + C I N D ? Note: r ead ME indicators current values +CIND: <ind>[, <ind>[,…]] OK A T+CIN D? +CIND: 2,2,1,0, 0,0,0 A T+ CIND= ? Note.
OnCell G2150I AT Command Set General Commands 3-13 command is ignored and th e mode m will re turn a +CME ERROR: <err> respo n se. Restrictions • Only b asic option and UI H framing is su pported. • Only conver gence layers type 1 and 3 ar e supported.
OnCell G2150I AT Command Set General Commands 3-14 Command Possible responses A T+CMUX= ? Note: Get possible values MUX: (0),(0),(1 -5),(1-255) ,(1-128),(0 -255),(1-12 8),(1-128) OK AT + C M U X ? Not.
4 4 Chapter 4 Call Control Commands This chapter includ e s in formation about the Call Con trol Commands of the OnCell G2 150I. The following topics are covered in this chapter: Dial Command: D .
OnCell G2150I AT Command Set Call Control Commands 4-2 Dial Command: D Description: The ATD command is used to set a voice, data or fax call. As per GSM 02.
OnCell G2150I AT Command Set Call Control Commands 4-3 Command Possible responses AT + C P B S ? Note: Which phonebook is selected ? +CPBS:”SM”,8,10 Note: ADN phone book is sel ected, 8 loc ations.
OnCell G2150I AT Command Set Call Control Commands 4-4 Command Possible responses AT H Note: Ask for disconnection OK Note: Every call, if any , ar e r eleased AT H 1 Note: Ask for outgoing call disco.
OnCell G2150I AT Command Set Call Control Commands 4-5 DTMF Signals: +VTD, +VTS +VTD descriptio n: The product ena bles the use r applicati on to send DTM F tones over the GSM network. Thi s comm and is used t o define t one duratio n (the de fault value i s 70 ms ± 5 ms, according to 3GPP 23.
OnCell G2150I AT Command Set Call Control Commands 4-6 Automatic Dialing with DTR: AT%Dn Description: This comm and enables and disables: • automatic dialing of the phone number stored in the first location of the ADN phonebook (or FDN phoneboo k, if it is activated using +CLCK command ).
OnCell G2150I AT Command Set Call Control Commands 4-7 activated using +CLCK command). Voice call (with semi-colon). AT%D1 Activates automatic DTR dialing if DTR switches from OFF to ON; Dials the phone num ber in the first location of the AD N phonebook (or FDN ph onebook, i f it is activated using +CLCK command).
OnCell G2150I AT Command Set Call Control Commands 4-8 Single Numbering Scheme: +CSNS Description: This command selects the bearer to be used when an MT single num bering scheme call is set up (see +CICB). Note: Setting the +CSNS command affect s the curren t value of +CICB.
OnCell G2150I AT Command Set Call Control Commands 4-9 Defined values: <Rgain>: reception g a in <Tgain>: transm ission gain AT + V G R = < v a l > for receive gain AT + V G T = <.
5 5 Chapter 5 Network Service Commands This chapter includ es in formation about the Network Service Co mmands of the OnCell G2150I. The following topics are covered in this chapter: Signal Qu ali.
OnCell G2150I AT Command Set Network Service Commands 5-2 Signal Quality: +CSQ Description: This command is used t o ascertain the r eceive d signal strengt h indication (<rssi>) and the chann el bit error rate (<ber>) with or with out a SIM card inserted.
OnCell G2150I AT Command Set Network Service Commands 5-3 +CME ERROR: 547 Emergency call is allowed without SIM Careful: Error co d e + CME ERROR: 546 or +CME ERROR: 547 are only return ed if SIM is not present. The fact that network supports emergency calls ( + CME ERRO R: 547) does not imply that emergency calls will work without a SIM.
OnCell G2150I AT Command Set Network Service Commands 5-4 AT + C O P S = 2 Note: Ask for der egistra tion fr om ne twor k OK Note: Succeeded AT + C O P S ? Note: Ask for cur rent PLMN +COPS: 2 Note: M.
OnCell G2150I AT Command Set Network Service Commands 5-5 0: Disable network registration un solicited result code (default) 1: Enable network re gistration code result code +C REG: <stat > 2: E.
OnCell G2150I AT Command Set Network Service Commands 5-6 AT + W O L M = 0 , 1 1 Note: Delete an entry at location 1 1 +CME ERROR: 21 Note: Invalid index Defined values: <mode> : 0 delete 1 write 2 read <loc> : location. If this parameter is not filled with <mode>=1, the location will be the first empty one.
OnCell G2150I AT Command Set Network Service Commands 5-7 A T+WOPN=0,999 99 Note: Give a wr ong operator +CME ERROR: 22 Note: Not found A T+W OPN=0,20801,36 Note: Give an operator in numeric format fo.
OnCell G2150I AT Command Set Network Service Commands 5-8 Selection of Preferred PLMN List: +CPLS Description: This command is used to select one PLMN selector with acce ss technology list in the SIM card that is used by AT+CPOL command.
OnCell G2150I AT Command Set Network Service Commands 5-9 A T+CPLS=? Note: Get possible values +CPLS: (0,1,2) OK Note: The 3 files with Acces technology ar e pr esent and can be selected A T+CPLS=? No.
OnCell G2150I AT Command Set Network Service Commands 5-10 AT + C P O L = , 0 Note: Select long alphanumeric format OK AT + C P O L ? Note: Ask for pr eferred list of networks with only EF_PLMNsel pr .
OnCell G2150I AT Command Set Network Service Commands 5-11 to get the maxim um index of the selected EF. <format>: 0 long alphanumeric form at for <oper> 1 short alphanum eric form at for <ope r> 2 numeric format for < oper> <oper>: character string or integer (see <format>) in d icating operator identifier.
6 6 Chapter 6 Security Commands This chapter includ e s in formation about the Security Comman ds of the OnCell G2150I. The following topics are covered in this chapter: Enter PIN: +CPIN Enter.
OnCell G2150I AT Command Set Security Commands 6-2 Enter PIN: +CPIN Description: This command is u s ed to enter the ME passwords (CHV1 / CHV2 / PUK1 / PUK2, etc.), that are required before any ME functionality can be used. CHV1/CHV2 is between 4 an d 8 digits long, PUK1/PUK2 is only 8 digits long.
OnCell G2150I AT Command Set Security Commands 6-3 AT + C P I N ? +CPIN: SIM PIN A T+CPIN =1235 +CME ERROR: 16 A T+CPIN =1236 +CME ERROR: 16 A T+CPIN =1237 +CME ERROR: 16 AT + C P I N ? +CPIN: SIM PUK.
OnCell G2150I AT Command Set Security Commands 6-4 A T+CPIN2=5678 Note: Enter PIN2 +CME ERROR: 3 Note: Operation n ot allowed, PIN2 previously enter e d After 3 unsuccessful attempts, PUK2 will then be requ ired.
OnCell G2150I AT Command Set Security Commands 6-5 Facility Lock: +CLCK Description: This command is u s ed by the application to lock, unlock , or interrogate an ME or network facility <fac>. Note: Test SI M cards (with MCC=001 & MNC=01) do not check “PS” , “PN”, “PU” , “PP” and “PC” locks.
OnCell G2150I AT Command Set Security Commands 6-6 • “AC”: All inComing barring services • “PN”: Network lock with an 8-digit passwo rd (NCK). • “PU”: Network Subset lock with an 8-digit password (NSCK). • “PP”: Service Provider lock with an 8-digit password (SPCK).
OnCell G2150I AT Command Set Security Commands 6-7 Change Password: +CPWD Description: This comm and is used by the a pplication to c hange a passw ord (PIN, call barring, NCK, etc.). The facility values (<fac>) are th e same as for the +CLCK command with a “P2” facility to manage SIM PIN2.
7 7 Chapter 7 Short Message Commands This chapter includ es in formation about the Shor t Messag e Commands of the OnCell G2150I. The following topics are covered in this chapter: Parameter Defini.
OnCell G2150I AT Command Set Short Message Commands 7-2 Parameter Definitions <da> Destination Address, coded lik e GSM 03.40 TP-DA <dcs> Data Codin g Schem e, coded like i n document [5].
OnCell G2150I AT Command Set Short Message Commands 7-3 Select Message Service: +CSMS Description: The supported services are originated (SMS-MO) and terminated short message (SMS-MT) + Cell Broadcast Message (SM S-CB) services.
OnCell G2150I AT Command Set Short Message Commands 7-4 A T+CNMI=2,2,0, 0,0 Note: <mt>=2 OK +CMT : “123456” ,”98/10/01, 12:30 00+ 00”, 129, 4, 32, 240, “15379”, 129, 5 <CR><.
OnCell G2150I AT Command Set Short Message Commands 7-5 Preferred Message Storage: +CPMS Description: This command allo ws the message storage area to be selected (for reading, writing, etc).
OnCell G2150I AT Command Set Short Message Commands 7-6 AT + C P M S ? Note: Read +CPMS: “SM”,4,10 , ”ME”,4,99,”ME”,4,99 OK Note: Read SMS fr om SIM; w rite, stor e SMS fr o m/to flash Defined values: <mem1> Memory used to list, read , and delete messages.
OnCell G2150I AT Command Set Short Message Commands 7-7 Defined values: <mode> PD U or text m ode 0 PDU mode 1 T ext mode The <pdu> m e ssage is com posed of the SC a ddress (00 m eans no SC a ddress given, use default SC address rea d with +CSCA command) an d the TPDU m essage.
OnCell G2150I AT Command Set Short Message Commands 7-8 Command Possible responses AT + C S D H = 0 Note: Set val ue to “d o not show ” OK AT + C S D H ? Note: Curr ent value +CSDH: 0 OK Note: Do .
OnCell G2150I AT Command Set Short Message Commands 7-9 1: SMS-DELIVERs are routed usi ng unsoli cited code: +C MTI: “SM”,<i ndex> 2: SMS-DELIVERs (e xcept class 2 m essages) are routed usin.
OnCell G2150I AT Command Set Short Message Commands 7-10 Command Possible responses A T+CMTI: “SM”,1 Note: New message r eceived AT + C M G R = 1 Note: Read the message +CMGR: “REC UNREAD”, .
OnCell G2150I AT Command Set Short Message Commands 7-11 Command Possible responses A T+CMGL=“REC UNREAD” Note: List u nr ead messages in text mo de +CMGL: 1,”REC UNREAD”,”01462908 00”,, &.
OnCell G2150I AT Command Set Short Message Commands 7-12 +CMGS: <mr>,, OK Note: Successful transmission A T+CMGS=<length><CR> Note: Send a message in P DU mode ( 1/3) <pdu> Not.
OnCell G2150I AT Command Set Short Message Commands 7-13 mode (default “STO UNSE NT” for +C MGW). Indicates the status of message in memory. If <stat> is omitted, the stored message is considered as a message to send .
OnCell G2150I AT Command Set Short Message Commands 7-14 but can be use d in PDU m ode (+CMGS). SRR: Status Report Requ est, b5=1 if a status report is requested.
OnCell G2150I AT Command Set Short Message Commands 7-15 A T+CMGD=1,0 OK Note: The message fr om the pr eferr ed message storage at the location 1 is deleted A T+CMGD=1,1 OK Note: All READ mess ages f.
OnCell G2150I AT Command Set Short Message Commands 7-16 Select Cell Broadcast Message Types: +CSCB Description: Th is command selects which types of CBM s are to be rece ived by the ME.
OnCell G2150I AT Command Set Short Message Commands 7-17 A T+W CBM=“10,100,1000 ,10000” Note: W r ite 4 message identifiers in EF- CBMI OK Note: CBMIs ar e stored in EF-CBMI A T +WCBM? Note: Read .
OnCell G2150I AT Command Set Short Message Commands 7-18 Command Possible responses AT + C P M S ? Note: Check the storage ar ea +CPMS: “SM”,3,10,”SM”,3,10,”SM” ,3,10 OK A T+CMGW =“+3314.
OnCell G2150I AT Command Set Short Message Commands 7-19 A T+CMGR=10 +CMGR: “REC UNREAD”,”+3366 0669023”,,”03/02/13,18 :36:35+00”<CR><LF> Do you want to change state ? OK Note:.
OnCell G2150I AT Command Set Short Message Commands 7-20 AT + C M G R = 1 Note: Read the first SMS from the SIM +CMGR: “REC UNREAD”,”0146 290 800”, “98/10/01 ,18:22:1 1+00”, <CR ><.
OnCell G2150I AT Command Set Short Message Commands 7-21 AT + W M C P = 0 Note: Copy all the SMS fr om the SIM to the Flash OK AT + C P M S ? Note: Rea d the SMS st orage +CPMS: “ME”,4,99,”ME”,4 ,99,”SM”,4,10 OK Note: 4 SMS ar e stored in the flash.
8 8 Chapter 8 Data Commands This chapter includ es in formation about the Data Commands of th e OnCell G2150I. The following topics are covered in this chapter: Using AT Commands Duri ng a Data Co.
OnCell G2150I AT Command Set Data Commands 8-2 Using AT Commands During a Data Connection To use AT Commands during a data conn ectio n (e.g., while the product is in online mode), it is necessary either to switch to offline mode, or to use the specific +WMUX command to enable Commands / Data multiplexin g.
OnCell G2150I AT Command Set Data Commands 8-3 6 4800 bp s (modem type: V.32 ) 7 9600 bp s (modem type: V.32 ) 8 Specific 12 9600 b ps (m odem ty pe: V.34) 14(*) 1400 bps (modem ty pe: V.34) 6 5 30 0 b ps (m odem type: V.110) 66 1200 bps (mode m type: V.
OnCell G2150I AT Command Set Data Commands 8-4 +CR: ASYNC For asynchronous tr ansparent +CR: REL ASYNC For asynch ronous non-transparent Command syntax: AT+CR=<mode> Command Possible responses A.
OnCell G2150I AT Command Set Data Commands 8-5 Command syntax: AT+ILRR = <value> Command Possible responses A T+ILRR=0 Note: Local port rate report disabled OK Note: Command valid A T+ILRR=1 Not.
OnCell G2150I AT Command Set Data Commands 8-6 Select Data Compression: %C Description: This command enables or disables dat a compression negotiati on if this feature is supported by the pr o duct .
OnCell G2150I AT Command Set Data Commands 8-7 V42 bis Data Compression Report: +DR Description: Th is command determines whether or not the use of V42bis is allowed for an incoming or outgoing data call, if the feature is provided by the produ ct. The intermediate result code repres ents current DCE-DCE dat a compressio n type.
9 9 Chapter 9 V24-V25 Commands This chapter includ e s in formation about the V24-V25 Co mmands of the OnCell G2150I. The following topics are covered in this chapter: Fixed DTE Rate: +IPR DTE.
OnCell G2150I AT Command Set V24-V25 Commands 9-2 Fixed DTE Rate: +IPR Description: This command specifies the data rate at which the DCE wi ll accept commands. Notes: y The serial autobauding feature is supported, and covers the follow ing serial speeds (only): 2400, 4800, 9600, 19200, 3840 0, 57600 bps.
OnCell G2150I AT Command Set V24-V25 Commands 9-3 DTE-DCE Character Framing: +ICF Description: Th is command is used to determine the local serial port start-stop (asynchronous) character framing used by the DCE.
OnCell G2150I AT Command Set V24-V25 Commands 9-4 A T+IFC=0,0 OK Note: New values Defined values: < DCE_by_D TE > 0: none (supported ) 1: XOn/X off local circ uit 103 ( not suppo rted) 2: RTS (s.
OnCell G2150I AT Command Set V24-V25 Commands 9-5 AT & D 1 Note: Modem switches from data to command mode when DTR switch es fr om ON to OFF OK Note: Command valid AT & D 2 Note: When DTR swit.
OnCell G2150I AT Command Set V24-V25 Commands 9-6 Defined values: <n> 0: DCE tra nsmission resul t code 1: Result c odes are su ppressed and not transm itted DCE Response Format: V Description: .
OnCell G2150I AT Command Set V24-V25 Commands 9-7 Auto-tests: &T Description: This command allows t he triggering of vari ous auto-tests. Command syntax: AT&T<n> Command Possible respons.
OnCell G2150I AT Command Set V24-V25 Commands 9-8 Restore Factory Settings: &F Description: This command is use d to restore t he factory setti ngs from EEPR OM. It onl y restores the para meters th at can be found in pa ragraph 19 Codes and val ues (Parameters Stora ge paragraph) wit h AT&F column checked.
OnCell G2150I AT Command Set V24-V25 Commands 9-9 Request Identification: I Description: This command causes t he product to t ransmit one or more li nes of specific information text Command syntax: A.
OnCell G2150I AT Command Set V24-V25 Commands 9-10 Data / Commands Multiplexing: +WMUX Description: Th is specific command allows managing the data / AT comman ds multiplexing Command syntax: AT+WMUX=<mode > Command Possible responses A T+WMUX=? + WMUX: (0-1) OK A T +WMUX? +WMUX : 0 OK Note: Data / Commands multiplexin g d isabled.
1 1 0 0 Chapter 10 GPRS Commands This chapter includ es in formation about the GPRS Commands of the OnCell G2150I. The following topics are covered in this chapter: Define PDP C ontext: + CGDCONT .
OnCell G2150I AT Command Set GPRS Commands 10-2 Define PDP Context: + CGDCONT Description: This Command specifies PDP contex t parameter valu es for a PDP context identified by the local context identification parame ter, <cid>. Four PDP c ontexts can be defined through MOXA software .
OnCell G2150I AT Command Set GPRS Commands 10-3 <PDP_address>: a string parameter that identifies the MT i n the address space a pplicable to the PDP. If the value is nu ll or omitted, th en a value m ay be provided by the TE durin g the PDP startup procedure, or a dynamic address w ill be requested.
OnCell G2150I AT Command Set GPRS Commands 10-4 A T+CGQREQ=? +CGQREQ: <PDP_type>, (li st of supported <precedence>s), (list o f su pported <delay>s), (list of supported <re liabil.
OnCell G2150I AT Command Set GPRS Commands 10-5 <reliability>: numeric parameter that specifies the reliability class 0: Subscribe d 1: Up to 1 000 (8 kbits/ s). 2: Up to 2 000 (16 kbit s/ s). 3: Up to 4 000 (32 kbit s/ s). 4: Up to 8 000 (64 kbit s/ s).
OnCell G2150I AT Command Set GPRS Commands 10-6 non-sensitive application that can cope with data loss. NOTE: For real-time traffic, th e QoS profile also requires ap propriate set tings for del ay and throughput. 3: Up to 4 000 (32 kbit s/ s). 4: Up to 8 000 (64 kbit s/ s).
OnCell G2150I AT Command Set GPRS Commands 10-7 Command Possible responses A T+CGQ MIN=[<cid> > [,<delay> [,<precedence [,< peak> [,<reliability .
OnCell G2150I AT Command Set GPRS Commands 10-8 A T +CGA TT=1 OK Defined values: <state>: indicates the state of GPRS attachment • 0: detached • 1: attached • 2: combined detach (GPRS and GSM de tach in th e same network request) • Other values are reserved and will result in an ERROR response to the execution command.
OnCell G2150I AT Command Set GPRS Commands 10-9 Enter Data State: +CGDATA Description: This command causes the MT to pe rform the necessary actions to set up communicat ion between the TE and the netwo rk. This m ay include pe rforming a G PRS attach and one PDP context activation.
OnCell G2150I AT Command Set GPRS Commands 10-10 A T+CGCLASS=? +CGCLASS: (“CG”,”CC”) OK A T+CGCLASS? +CGCLASS: “CC” OK Defined values: <class>: a string param eter that indicates the.
OnCell G2150I AT Command Set GPRS Commands 10-11 Command Possible responses +CGSMS= [<service>] OK ERROR +CGSMS? +CGSMS: <service> OK +CGSMS=? +CGSMS: (list of cu rrently available <ser.
OnCell G2150I AT Command Set GPRS Commands 10-12 mode), if MT result code b uffer is ful l, the oldest ones can be discar ded. Defined events: The following unsolicited result cod es and the correspon.
OnCell G2150I AT Command Set GPRS Commands 10-13 2: enable network registration and location information unsolicited result code +CGREG: <stat>[,<lac>,<ci>] <stat>: 0: not regi.
OnCell G2150I AT Command Set GPRS Commands 10-14 Network Requested PDP Context Activation In this mode of operation, the MT be haves like a n answering modem and accepts the normal V.
OnCell G2150I AT Command Set GPRS Commands 10-15 Command syntax: Command Possible responses +CGAUT O=[<n>] OK ERROR +CGAUT O? +CGAUT O: <n> OK +CGAUT O=? +CGAUT O: (0-3) OK Defined values:.
OnCell G2150I AT Command Set GPRS Commands 10-16 During the PDP startup procedure the MT has the PDP type and the PDP address provided by the network in the Request PDP Context Activation message. If a <cid> is given its information must match th e PDP type and PDP address in the network request as follows: The PDP typ e must match exactly.
OnCell G2150I AT Command Set GPRS Commands 10-17 Show PDP Address: +CGPADDR Description: The exclusion command returns a lot of PDP addresses for the specified context identifiers.
OnCell G2150I AT Command Set GPRS Commands 10-18 +CRING: GP RS GPRS network request for PDP context act ivation If the MT is u nable to anno unce to the TE t he network’s request (fo r exam ple it is in V.25t er on line data state) the MT rejects th e request.
OnCell G2150I AT Command Set GPRS Commands 10-19 GPRS Parameter Customization: + WGPRS Description: This command modi fies some G2150I GP RS param eters: ‧ the ATTACH-STAT US (the ME does or not per.
OnCell G2150I AT Command Set GPRS Commands 10-20 Command Possible responses AT + W G P R S ? Note: - Automatic re-attachment at init not activated - Automatic reactivation of PDP context at init not a.
OnCell G2150I AT Command Set GPRS Commands 10-21 some OS-speci fic frames, for accurate trans fer rate measurem ents. <parameter>: a numeric parameter that cont rols the operation defined by < mode> if it is equal to 0, 1, 2, or 3.
OnCell G2150I AT Command Set GPRS Commands 10-22 Example 2: AT + C G C L A S S = ” C G ” OK +CGREG: 1 A T +CGDCONT=1,” IP”,”intern et” OK A T +CGQREQ=1,1,4,5,2,14 OK A T +CGQMIN=1,1,4,5,2,.
1 1 1 1 Chapter 11 MOXA Proprietary Commands This chapter includ es information ab ou t the MO XA propri et ary Com m ands of the OnCel l G2150 I. The following topics are covered in this chapter: .
OnCell G2150I AT Command Set MOXA Proprietary Commands 11-2 Firmware Upgrade: *UPG Description: This command trigge rs a X-m odem(checksum) downloa ding session f or G2150I firmware image. . Notes: • There will always be risks when performing the firmware upgrade.
OnCell G2150I AT Command Set MOXA Proprietary Commands 11-3 Restore Default Setting: *DEFAULT Description: Th is command resets the G2150I to its factory default.
OnCell G2150I AT Command Set MOXA Proprietary Commands 11-4 Automatic PIN Entry: *USEPIN Description: This command enables/disables the automatic PIN code entry function when G2150I is bo oting up Com.
OnCell G2150I AT Command Set MOXA Proprietary Commands 11-5 Initial Strings: *BOOTSTR Description: Th is command enables/disables the initial strings Command syntax: AT*BOOTSTR=<m> AT*BOOTSTR<.
OnCell G2150I AT Command Set MOXA Proprietary Commands 11-6 Serial Port Configuration: *SERIAL Description: Th is command configures the serial port setting s Command syntax: AT*SERIAL=<n>,<b.
OnCell G2150I AT Command Set MOXA Proprietary Commands 11-7 SMS Tunnel Mode: *SMS Description: This command confi gures the SMS T unnel m ode settings Command syntax: AT*SMSIN=<encoding>,<rec.
OnCell G2150I AT Command Set MOXA Proprietary Commands 11-8 *SMSOUT : Configured Encode: 7-Bits GSM T ext Receiver1: +8862891912 30 Receiver2: +8862891912 31 A T*SMSIN=0,+886289191230,+886289191231 *S.
A A Appendix A Result Codes, Failure Causes, and Other Tables This chapter includ e s in formation about the Result Codes, Failure Causes, and Other Tables of the OnCell G2150I.
OnCell G2150I AT Command Set Result Co des, Failure Causes,, and Other Tables A-2 ME Error Result Code: +CME ERROR: <error> <error> Meaning Re s ulting from the follo w in g commands 3 Operat ion not allow ed All GSM 07.07 commands ( +CME ERRO R: 3) 4 Operat ion not suppo rted All GSM 07.
OnCell G2150I AT Command Set Result Co des, Failure Causes,, and Other Tables A-3 148 unspec ified GPR S error All GPRS comma nds 149 PDP aut hentication failure +CGACT +CGDATA ATD*99 150 invalid mobi.
OnCell G2150I AT Command Set Result Co des, Failure Causes,, and Other Tables A-4 518 SIM ToolKit indication not received. +ST GI 519 Reset the product to activate or change a new echo cancellation algo. +ECHO, +VIP 520 Automatic abort about get plmn list for an incoming call.
OnCell G2150I AT Command Set Result Co des, Failure Causes,, and Other Tables A-5 29 Facility rejected 30 Response to STATUS ENQUIRY 31 Normal, unspecified 34 No circuit/channel available 38 Network o.
OnCell G2150I AT Command Set Result Co des, Failure Causes,, and Other Tables A-6 231 PDP deactivation cause LLC link activation failed 232 PDP deactivation cause NWK reactivation wit h same TI 233 PD.
OnCell G2150I AT Command Set Result Co des, Failure Causes,, and Other Tables A-7 Cause No. 21 : “Short m essage transfer rejected” This cause indi cates that the equipm ent sending this cause doe.
OnCell G2150I AT Command Set Result Co des, Failure Causes,, and Other Tables A-8 mandatory i nformati on element is missing a nd/ or has a content error (t he two cases are undistin guishabl e).
OnCell G2150I AT Command Set Result Co des, Failure Causes,, and Other Tables A-9 +CLIP: <num ber>, <type> [,,,<alpha>] As verbose Incomi ng Call Presenta tion + C M T : < o a >.
OnCell G2150I AT Command Set Result Co des, Failure Causes,, and Other Tables A-10 Intermediate Result Codes Verbose Result Code Numeric (V 0 set) Description Verbose Result Code Nu meric (V0 set) Des.
An important point after buying a device Moxa Technologies G2150I (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Moxa Technologies G2150I yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Moxa Technologies G2150I - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Moxa Technologies G2150I you will learn all the available features of the product, as well as information on its operation. The information that you get Moxa Technologies G2150I will certainly help you make a decision on the purchase.
If you already are a holder of Moxa Technologies G2150I, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Moxa Technologies G2150I.
However, one of the most important roles played by the user manual is to help in solving problems with Moxa Technologies G2150I. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Moxa Technologies G2150I along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
