

It is important to run water through your coffee maker in order to rinse the machine. You can also run water through to warm your coffee machine.
It is important to descale as the performance of your coffee maker may be impaired by limescale and other impurities in the water supply.

The use of any electrical appliance requires the following common sense safety rules.
Primarily there is danger of injury or death and secondly the danger of damage to the appliance. These are indicated in the text by the following two conventions:
Treating scalds
Personal safety

Check that the voltage on the rating plate of your appliance corresponds with your house electricity supply which must be A.C. (Alternating current).
Should the fuse in the 13 amp plug require changing a 13 amp BS1362 fuse must be fitted.
For appliances with fitted plug. If the socket outlets in your home are not suitable for the plug supplied with this appliance the plug should be removed and the appropriate one fitted.
⁄ Warming plate ¤ Power light ‹ Hot water/steam selector › On/off switch fiBrewing head flFilter lock ‡ Filter holder · Drip tray water level indicator ‚ Non slip rubber feet „ 1 cup filter ‰ 2 cup filter  Measuring spoon Ê Compactor Á Removable drip tray Ë Froth attachment È Steam nozzle Í Display Î 1.7L removable water reservoir Ï Pod filter Ì Coffee or steam lever
STEAM
OFF
Ì
COFFEE
Ë È
Á
Ê
Â
The first time you use your coffee maker Operate the coffee maker with water only.
Before first use
For best results before making your espresso/cappuccino the cups should be warmed. This can be done on the warming plate but please note that this may take up to 20 minutes depending upon the type of cup used.
Before using your coffee maker for the first time or if you have not used it for some time, rinse the machine by running water through. Follow the procedure for making espresso coffee overleaf, without coffee in the filter holder.

1 Remove to fill the water reservoir, A slide the water tank upwards using the handle. Open the lid of the water reservoir Î by pulling up and sliding backwards.
IMPORTANT: Be sure not to overfill the filter with too much coffee, and wipe around the edge of the filter to remove any coffee grounds. 6 Place the filter holder ‡ on the brewing head fiand position the handle so it points to the left. F • Ensure the filter holder is flat against the brewing head and turn the handle towards the right G as far as it will go. 7 Place 1 or 2 pre-heated cups below the holes in the filter holder H and I. When the coffee maker is at the correct temperature the sign will be displayed. 8 Move the lever down to the coffee setting. You will hear the machine make a pumping noise, this is normal. 9 Once the cups are filled to the desired level, pull the lever to the off position. Water will still filter through for approximately 8 seconds after the machine has been turned off. 10Carefully remove the filter holder by turning the handle slowly to the left.
Ensure the coffee/steam lever Ì is in the off position. 1 Plug the unit into the power outlet. 2 Switch the unit on by pressing the on/off switch ›. The blue 'power light' ¤ and the display Í will illuminate. 3 Pre-heat your coffee cups by placing them upside down on the warming plate ⁄.
E F
C D
G H

11To remove the used coffee grounds from the filter, push the filter lock flforward over the edge of the filter and turn the filter holder upside down. Gently tap out the coffee. J 12Once the sign shows, your machine is ready to make the next espresso.
6 Move the lever down to the coffee setting. You will hear the machine making a pumping noise, this is normal. 7 Once the cup is nearly filled to the desired level, move the lever back to the off position. Water will filter through for approximately 8 seconds after the machine has been turned off. 8 Remove by turning the filter holder slowly to the left. 9 To remove the pod from the filter, push the filter lock flforward over the edge of the filter and turn the filter holder upside down. P 10Once the sign shows, your machine is ready to make the next espresso.
1 Select the pod filter Ï and place in the filter holder ‡. K 2 Remove the espresso pod from the packaging. L 3 Place the coffee pod in the filter Ï. Ensure that the flap is placed inside the filter. M 4 Place the filter holder ‡ on the brewing head fiand position the handle so it points left. Ensure the filter holder is flat against the brewing head and turn the handle towards the right N as far as it will go. 5 Place a pre-heated cup below the holes in the filter holder. O
N M
K L P O

7 Hold the jug under the steam nozzle so that the head of the froth attachment is immersed in milk and push the lever up to the steam setting. R You will hear the machine making a pumping noise, this is normal.
The froth attachment makes it easy to produce frothy milk for cappuccino.
Ensure the coffee/steam lever is in the off position. 1 Before using the steam nozzle, remove the filter holder. 2 Attach the froth attachment Ë to the end of the steam nozzle È. Q
IMPORTANT: For the froth enhancing attachment to work you must ensure that it is pushed firmly onto the steam nozzle. 3 Fill the water reservoir with cold tap water. 4 Swing the steam nozzle with the froth attachment to the side of the machine. 5 Press the steam button ‹ when the unit is ready to make steam, the sign shows. This sign will flash on the display until the machine reaches the correct temperature to make steam when it becomes fixed. 6 Pour cold milk into a suitable jug. Use approximately 100ml for each cappuccino.
The milk is ready as soon as it forms a soft, thick layer of foam on the top. If the milk starts to make large popping bubbles, you have boiled the milk and it will therefore not froth. If this happens replace with chilled milk. Do not boil the milk.

Cleaning and maintenance
You may want to top up your espresso with hot water for a longer drink or to make other hot water drinks such as tea or instant soups using the steam nozzle. 1 Ensure the unit is cold before removing the froth attachment from the steam nozzle. 2 Press the steam/hot water button. ‹ The display shows the icon flashing. 3 Follow the 'steam function' instruction, push the lever up to the steam/hot water function R.
You must clean the steam nozzle and froth attachment immediately after each use. 1 Simply wipe the steam nozzle, warming plate and exterior with a clean, damp cloth. Do not use any abrasives or metal scourers as this will damage the finish on the unit.
Briefly push the lever to the steam setting to clear any remaining milk out of the steam nozzle.
Should the holes in the filters become blocked with coffee granules use a fine bristled brush.
To make hotter coffee and to warm your coffee cups you may preheat your machine. This can be achieved by following the 'espresso operation' by passing hot water through the coffee maker but without using coffee.
When your coffee maker is not being used, we recommend that you do not leave the filter holder attached to the machine as this will reduce the life of the gasket.
Cups should be placed upside down on the warming plate. Please note that this may take up to 20 minutes depending upon the type of cup used.

1 The water level indicator · appears through the grid to indicate that the drip tray is full. 2 Remove the grid of the drip tray by placing fingers in the two holes in the centre of the drip tray and lift off. S This must be done regularly or as soon as the red water level indicator appears through the grid. 3 Lift the front of the drip tray up and slide it out. T 4 Lift off the plastic lining of the drip tray. U Clean the drip tray and its grid with water and a little washing up liquid, rinse and dry. 5 Reverse the procedure to reassemble. Note: Ensure that when you are replacing the drip tray that the plastic lining is in the correct position.
U

If you have any difficulty with your appliance, do not hesitate to call us. We are more likely able to help than the store from where you bought it.


appliance must have been used according to the manufacturers instructions. For example coffee makers should have been regularly descaled.
It is important to retain the retailers receipt as proof of purchase. Staple your receipt to this back cover for future reference.
Morphy Richards shall not be liable to replace or repair the goods under the terms of the guarantee where: 1 The fault has been caused or is attributable to accidental use, misuse, negligent use or used contrary to the manufacturers recommendations or where the fault has been caused by power surges or damage caused in transit. 2 The appliance has been used on a voltage supply other than that stamped on the products. 3 Repairs have been attempted by persons other than our service staff (or authorised dealer). 4 Where the appliance has been used for hire purposes or non domestic use. 5 Morphy Richards are not liable to carry out any type of servicing work, under the guarantee. 6 Plastic filters for all Morphy Richards kettles and coffee makers are not covered by the guarantee.
Please quote the following information if the product develops a fault. These numbers can be found on the base of the product. Model no. Serial no. All Morphy Richards products are individually tested before leaving the factory. In the unlikely event of any appliance proving to be faulty within 28 days of purchase it should be returned to the place of purchase for it to be replaced.
If the fault develops after 28 days and within 24 months of original purchase, you should contact the Helpline number quoting Model number and Serial number on the product, or write to Morphy Richards at the address shown.
You may be asked to return the product (in secure, adequate packaging) to the address below along with a copy of proof of purchase.
Subject to the exclusions set out below (see Exclusions) the faulty appliance will then be repaired or replaced and dispatched usually within 7 working days of receipt.
This guarantee does not confer any rights other than those expressly set out above and does not cover any claims for consequential loss or damage. This guarantee is offered as an additional benefit and does not affect your statutory rights as a consumer. • This guarantee is valid in the UK and Ireland only.
If for any reason this item is replaced during the 2 year guarantee period, the guarantee on the new item will be calculated from original purchase date. Therefore it is vital to retain your original till receipt or invoice to indicate the date of initial purchase.
To qualify for the 2 year guarantee the

Morphy Richards products are intended for household use only.
The After Sales Division Registered address Morphy Richards Ltd, Mexborough South Yorkshire, England, S64 8AJ
Morphy Richards has a policy of continuous improvement in product quality and design. The company, therefore reserves the right to change the specification of its models at any time.
Helpline (office hours) UK 0870 060 2610 Republic of Ireland 1800 409119
CM47507M UK Rev 1 02/05
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.