Instruction/ maintenance manual of the product STANDARD Mio
Go to page of 12
Aquachlor Salt Water Chlorinator Owners Manual Model Standard and Self Clean C Series II Manufactured in Australia By Monarch Pool Systems www.monarch poolsystems.
2 Aquachlor Salt Chlorinator Thankyou for purchasing a Quality Aquachlor Pool and Spa Product. Please read all information in this Manual carefully before installing or operating your AQUACHLOR SALT CHLORINATOR.
3 INSTALLATION INSTRUCTIONS FOR AQUACHLOR C and SC INSTALLING THE POWER SUPPLY : Select a convenient well-ventilated location within one metre of filter equipment and mount the Power Supply vertically onto a post or wall 1.5 metres above ground level.
4 PRE - START UP PROCEDURE : Before operating your Aquachlor Chlorinator please ensure the following items have been added to your pool: • SALT - Load salt into the pool at a minimum rate of 40kg per 10,000 litres (0.4%). Connect vacuum system and slowly vacuum until salt dispersal is complete.
5 BAR METER WARNING LED REASON/ACTION Off Green 1. Start – up delay functioning. 2. System Control set below max. Cell is turned off. (Refer System Control page 7). Off Red 1. Gas detected. Check pump/pipes for damage. 2. Gas sensor not connected to cell 4 or 5 LEDs on Green System operating normally 1 to 5 LEDs on Red 1.
6 If the Cell is OFF and you wish to check its operation, simply turn the System Control to MAX and the Cell will turn ON. Once checked, adjust the System Control back to the desired position and after a few minutes the Cell will turn OFF again. To turn the Cell OFF, simply turn the System Control to MIN.
7 Terminal Block the coloured wires from your pool light are connected. The Light Transformer is for use with 12volt pool lights, maximum power is 150Watt. Please Note: Only one light can be connected to each light transformer. If more than one light is required please refer to your Aquachlor dealer.
8 Aquachlor C Standard Aquachlor SC Self Clean C Standard Systems Model C Replacement Cell Model to order SC Self Clean Systems Model SC Replacement Cell Model to order 260 260 250 250 390 390.
9 Stabiliser should be added at the rate of 500 grams for every 10,000 litres of water. To add, place the required amount in a stocking and tie a brick to it. Place the stocking in front of the return jet. It will dissolve in 2 – 3 days. Stabiliser should be maintained at a level of 30 – 50 ppm.
10 The Aquachlor unit has a built in warning system to minimise damage resulting from insufficient salt levels, however, the ultimate responsibility is on the owner to ensure adequate salt levels are maintained all year round.
11 Aquachlor Model C (Standard) Aquachlor Model SC (Self Clean) Productio n maximum grams/hou r (100%) Production * grams/hour (65% equivalent) Chlorine produce d over 8 hours grams (100%) Equivalent in dry granulated chlorine grams (65%) Equivalent in liquid chlorine litres (12%) 220 250 16.
12 IMPORTANT: ALWAYS INSIST ON GENUINE AQUACHLOR REPLACEMENT PARTS. If it is necessary to replace the Electrolytic Cell, beware of “look alikes”. Only the Genuine Aquachlor Cell is designed and warranted to operate with the Aquachlor Power Supply.
An important point after buying a device Mio STANDARD (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Mio STANDARD yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Mio STANDARD - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Mio STANDARD you will learn all the available features of the product, as well as information on its operation. The information that you get Mio STANDARD will certainly help you make a decision on the purchase.
If you already are a holder of Mio STANDARD, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Mio STANDARD.
However, one of the most important roles played by the user manual is to help in solving problems with Mio STANDARD. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Mio STANDARD along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
