Instruction/ maintenance manual of the product 25 Miller
Go to page of 12
arr ow 25 arr ow 25 Fluid Head OPERA T OR’S MANU AL #1022 Arrow 25 Fluid Head.
1 Fea tures and Controls Fig. 1 Sliding Platform Camera Screws T ilt Lock T ilt Drag Control Bubble Level 1/4” and Pin Adaptor Camera Plate Quick Release Knob Safety T a b Counterbalance Selector P .
2 Fig. 1 P an Handle P an Handle Clamp Sliding Platform Lock Clamp Nut T ilt Lock P an Lock Threaded Stud Fig. 2 Fea tures and Controls.
3 Thank you for pur chasing the Arrow 25 Fluid Head. The Arr ow 25 Fluid Head has been designed to suit payload capacities from lightweight D VCAM up to standard configuration ENG cameras.
4 Weight - kg (lb) 3.0 (6.6) P ayload Range - kg (lb) 5 - 14 (11.0 - 30.9) Max Capaci ty - kg (lb ) 25 (55.1) T ilt Drag 5 Selectable fluid drag positions + 0 T ilt Range + 90 o / -75 o T ilt Lock P .
5 The operating instructions are described in six steps. Please read and understand these instructions before using this equipment. Do not omit any steps. 1 Fluid Head Set-up 1.1 Loosen the P AN HANDLE CLAMP fully then rotate the P AN HANDLE until it is approximately perpendicular to the THREADED STUD (fig.
2. Camera Set-up 2.1 Remove the CAMERA PLA TE by pulling down the SAFETY T AB while rotating the QUICK RELEASE KNOB to the left. The CAMERA PLA TE should pop out. 2.2 Refer to the Camera’ s owners manual for correct method of attachment to the CAMERA PLA TE.
3. Counterbalance Control The counterbalance system was designed to neutralise the effect of the camera weight when it is tilted. The Arrow 25 Fluid Head offers a 4 position counterbalance system which can be operated via the COUNTERBALANCE SELECTOR (fig.
Oper ating Instructions 4. P an / T ilt Dr ag Control. The Arrow 25 Fluid Head offers 5 selectable positions of fluid drag + zero setting in the Pan and T ilt. The settings are equally stepped from light drag in position 1 up to heavy drag in position 5, the drag plates are completely disengaged in position zero.
Illumination Button Retaining Screw Battery Battery Door The Arrow 25 Fluid Head offers high quality surface coatings, dust and moisture seals. Miller recommends keeping the Fluid Head clean at all times by using soft brushes and lint free cloth to wipe over the surfaces.
The Arrow 25 Fluid Head can be stored for extended periods; Miller recommends storage in a Miller Soft Case and the following: ◗ Remove battery . ◗ Clean the external surfaces. ◗ Keep in a dry place awa y from direct sunlight. ◗ Loosen off P AN & TIL T LOCK.
www .millertripods.com MILLER CAMERA SUPPORT EQUIPMENT 30 Hotham P arade Artarmon, Sydney NSW 2064 Australia T el: +61 2 9439 6377 Fax: +61 2 9438 2819 Email: sales@miller .
An important point after buying a device Miller 25 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Miller 25 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Miller 25 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Miller 25 you will learn all the available features of the product, as well as information on its operation. The information that you get Miller 25 will certainly help you make a decision on the purchase.
If you already are a holder of Miller 25, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Miller 25.
However, one of the most important roles played by the user manual is to help in solving problems with Miller 25. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Miller 25 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
