Instruction/ maintenance manual of the product W 1945 Miele
Go to page of 72
Operating instructions for Washing machine W 1945 To avoid the risk of accidents or damage to the machine it is essential to read these instructions before it is installed and used for the first time.
Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and should be recycled. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of babies and young children.
Caring for our environment .........................................2 Warning and Safety instructions .....................................6 Operating the washing machine .....................................1 3 Control panel .........................
Detergent .......................................................3 6 The correct detergent ..............................................3 6 Water softener ....................................................3 8 Washing with several components .......
Levelling the machine ..............................................5 7 Screwing out and adjusting the feet .................................5 7 Building under a worktop .........................................5 8 Washer-dryer stack .................
This washing machine conforms to current safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the washing machine, please read these instructions carefully before using it for the first time.
Safety with children ~ Children 8 years and older may use, clean or maintain the washing machine without supervision only if they have been shown how to do so in a safe way and understand the hazards involved. ~ Children under 8 years of age must be kept away from the machine unless they are constantly supervised.
Technical safety ~ Before setting up the washing machine, check it for any externally visible damage. Do not install or use a damaged washing machine. ~ Before connecting the washing machine, ensure that the connection data on the data plate (voltage and frequency) match the mains electricity supply.
~ Unauthorised repairs could result in unforeseen dangers for the user, for which Miele cannot accept liability. Repairs should only be undertaken by a Miele approved service technician. ~ If the connection cable is faulty it must only be replaced by a Miele approved service technician to protect the user from danger.
Correct use ~ Do not install your washing machine in rooms where temperatures below freezing may occur. Frozen hoses may burst or split. The reliability of the electronic control unit may be impaired at temperatures below freezing point.
~ If the correct amount of detergent is dispensed, the machine should not need to be descaled. If, however, you do wish to descale the machine only use proprietary non-corrosive descaling agents and strictly observe the instructions on the packaging.
Accessories ~ Accessory parts may only be fitted when expressly approved by Miele. If other parts are used, guarantee, performance and product liability claims will be invalidated. Miele cannot be held liable for damage caused by non- compliance with these Warning and Safety instructions.
Control panel a Display See the following page for more information. b Delay start button ( V )* For delaying the start time of a programme. c Temperature button (OK)* For selecting a temperature. d Spin speed button ( W )* For selecting the final spin speed or Rinse hold / e or No .
Second function of the Delay start ( V ), Temperature (OK) and Spin speed ( W ) buttons These buttons have a second function when Eco 4 is selected and also in the programmable functions.
The programme packages offer you the opportunity to add a number of special programmes to the standard range of programmes supplied with your machine. These programme packages have to be downloaded by a Miele service engineer.
Before using the machine for the first time ensure that it is correctly installed and connected. See "Installation and connection". Also check that the drain filter is securely tightened to prevent the risk of leaks during use. See "Installation and connection".
Energy and water consumption – Water consumption and energy usage are determined by the size of the load. To make the most out of your machine, load the maximum dry load for the programme you are using. – When smaller amounts of laundry are washed, the automatic load recognition system will reduce the amount of water, time and energy used.
Eco feedback The Eco feedback button is used for calling up information about the machine's energy and water consumption. The Eco feedback button must be held in to display this information. Pressing the Eco feedback button gives two different types of information: – Before and during the programme an estimate is shown.
Brief instructions The headings numbered A , B , C ,... show the operating sequence and can be used as brief instructions. A Sort the laundry ^ Empty all pockets. , Foreign objects (e.g. nails, coins, paper clips, etc.) can cause damage to garments and components in the machine.
B Switch on the washing machine C Load the drum ^ Press the Door button to open the drum door. ^ Unfold the laundry and load loosely into the drum. Mixing both large and small items gives better wash results and also helps distribute the load evenly during spinning.
Further programmes are available under the programme setting Eco 4 . B Selecting programmes using the programme selector at the Eco 4 position and the display ^ Turn the programme selector clockwise until the indicator light for the Eco 4 programmes comes on.
F Select an extra option(s) ^ Select any extra options by pressing the appropriate button. The relevant indicator light will come on to show which extra option has been selected. Not all the extra options are suitable for use with every programme. You can only select extra options which are compatible with the programme being used.
G Select Delay start (if required) The start of a programme can be delayed from 30 minutes up to 24 hours, allowing you to make use of night-time economy electricity rates, for example. See "Delay start" for more information. H Add detergent It is important to dispense the correct amount, because.
I Start the programme ^ Press the flashing Start/Stop button. If a delay start time has been selected, then this will count down in the display. At the end of the delay start time or im - mediately after the programme has started (if no delay start time has been selected) the estimated programme duration will appear in the display.
Final spin speed You can reduce the final spin speed. However, you cannot select a final spin speed higher than that shown in the chart above. Rinse and interim spin There is a spin after the main wash and between the rinses. A reduction in the final spin speed will also reduce the interim spin speed.
Delay start allows you to choose when you want the programme to start. The start of a programme can be delayed from 30 minutes up to a maximum of 24 hours, allowing you to make use of night-time economy electricity rates, for example. Selecting delay start ^ Press the Delay start button.
Please refer to the separate booklet for information on programmes available as additional programme packages. Programme chart 27 Cottons 9876 * cold to 90°C Max. load 7.0 kg Use for Cotton, linen or cotton mix fabrics, e.g. table linen, towelling, underwear, T-shirts etc.
Programme chart 28 Intensive plus cold to 95°C Max. load 7.0 kg Use for Mixed loads of heavily soiled garments suitable for the Cottons and Minimum iron programmes. Sort according to colour. Notes – The pre-wash additional function will be activated automatically.
Programme chart 29 Automatic plus 7621 * cold to 40°C Max. load 5.0 kg Use for Mixed loads of garments suitable for the Cottons and Minimum iron programmes.
The following extra options can be selected in addition to the programme: Short Pre-wash Pre-wash + Soak Extra quiet Cottons XXXX Minimum iron XXXX Delicates XXXX Woollens / X Express 20 X 1) X Intens.
Washing The figure quoted in the bucket is the maximum temperature the garment can be washed at. The number of bars under the symbol indicates the level of agitation permitted.
Main wash Rinses Spinning Water level Wash rhythm Water level Rinses Interim spin Final spin Programme sequence 32 Cottons d a ( 2-4 1)2) LL Minimum iron ( c e 2-3 3) LL Delicates e d e 3 – L Woolle.
d = Low water level ( = Medium water level e = High water level a = Intensive rhythm b = Normal rhythm c = Gentle rhythm d = Sensitive rhythm e = Ultra sensitive rhythm f = Handwash rhythm This machine has fully electronic controls with automatic load recognition.
Cancelling a programme You can cancel a programme at any time after it has started. ^ Press the Start/Stop button. Cancel programme ^ Press the flashing Start/Stop button again. The suds will be pumped away. If you want to remove the laundry: ^ Press the Door button.
Adding or removing laundry after a programme has started ^ Press the Door button to open the drum door. ^ Add or remove items. ^ Close the drum door. The programme will continue automatically. Please note: Once a programme has started the machine cannot recognise any adjustment to the load.
The correct detergent All modern detergents produced for automatic washing machines are suitable. Use dispensing aids, e.g. balls, if these are supplied with the detergent. Tablets are suitable for full loads, but note that it may be impractical to reduce tablets for smaller loads.
Detergent 37 Universal detergent Detergent for coloureds Detergent for delicates Specialist detergent* Proofing agent** Fabric conditioner Minimum iron X X – – – X Cottons X X – – – X Deli.
The right amount to dispense will depend on the following: – The quantity of laundry – The soiling level of the laundry Lightly soiled No visible dirt or stains. Possibly slight body odour. Normally soiled Visibly dirty and/or just a few slight stains.
Fabric conditioners and liquid starch Starch Stiffens and gives body to items of laundry, e.g. shirts, tablecloths and bed linen. Fabric conditioners Make garments soft to handle and help prevent static cling when tumble drying.
A range of Miele branded cleaning and conditioning agents is available to order from the Miele Spare Parts Department or via the internet at www.miele-shop.com. Cleaning the drum (Hygiene info) Washing at low temperatures and/or using liquid detergent can cause bacteria and unpleasant smells to build up in the machine.
Cleaning the siphon and conditioner channel 1 . Remove the siphon from compartment § and rinse under warm running water. Clean the siphon tube in the same way. 2 . Replace the siphon. ^ Clean the fabric conditioner channel using a brush and warm water.
Cleaning the filter in the water inlet The washing machine has a filter to protect the water inlet valve. The accessible filter in the union in the open end of the inlet hose should be checked every six months, or more often if there are frequent interruptions to the external water supply.
With the help of the following notes, minor faults in the performance of the machine, some of which may result from incorrect operation, can be put right without contacting the Service Department.
The following fault messages appear in the display and the programme stops Fault message Possible cause Remedy A ; Drain fault – The water outlet is blocked or restricted. – The drain hose has been fixed too high. – Clean the drain filter and the drain pump.
The following fault messages appear in the display at the end of the programme Fault message Possible cause Remedy Heating fault The washing machine cannot heat. Start the programme again. If the fault message appears again, contact the Service Department.
General problems Problem Possible cause Remedy The machine shakes during the spin cycle. The machine feet are not level. Level the machine (see "Installation and connection"). The laundry has not been spun properly and is still wet. The machine detected an imbalance during the final spin and reduced the spin speed automatically.
An unsatisfactory wash result Problem Possible cause Remedy Liquid detergent does not give the required result. Liquid detergents usually contain no bleaching agents. They do not remove fruit, coffee and tea stains. – Use a general purpose detergent containing a bleaching agent.
The drum door does not open when you press the Door button Possible cause Remedy The machine is not connected to the electricity supply and/or is not switched on. Insert the plug in the socket and switch on and/or switch the machine on with the _ button.
Opening the drum door in the event of a blocked drain outlet and/or power failure ^ Switch the washing machine off. There is a lever behind the detergent drawer fascia panel. ^ Remove the lever. ^ Use it to open the access flap. Blocked drain outlet If the drain outlet is blocked, up to 25 litres of water will be retained in the machine.
Once the flow of water ceases: ^ Remove the drain filter completely. ^ Clean it thoroughly. ^ Remove any foreign objects (e.g. buttons, coins, etc.) and fluff from the filter housing. Turn the impeller by hand to check that it rotates freely. Any foreign object causing an obstruction should be removed.
In the event of any faults which you cannot remedy yourself, please contact: – your Miele Dealer or – Miele (see back cover for contact details). When contacting your Dealer or Miele, please quote the model and serial number of your machine, both of which are shown on the data plate visible above the porthole glass when the door is open.
Front view a Inlet hose (tested to withstand pressure of at least 7,000 kPa) b Electricity supply cable c - f Flexible drain hose (with detachable swivel elbow) g Detergent dispenser drawer h Control .
Rear view a Protruding lid for holding when moving the machine b Electricity supply cable c Inlet hose (tested to withstand pressure of at least 7,000 kPa) d Drain hose e Transport clip for inlet and drain hoses f Safety cap for transit bars g Transport clip for inlet and drain hoses and for storing transit bars when not in use.
Installation surface A concrete floor is the most suitable installation surface for a washing machine, being far less prone to vibration during the spin cycle than wooden floorboards or a carpeted surface. Please note: ^ The machine must be level and securely positioned.
^ Using the spanner supplied, turn the left-hand transit bar 90°, then ^ withdraw the transit bar. ^ Turn the right-hand transit bar 90°, then ^ withdraw the transit bar.
, To avoid the risk of injury the holes for the transit bars must be covered after the transit bars have been removed. ^ Plug the holes with the plastic caps as illustrated. ^ Secure the transit bars to the back of the washing machine. Make sure that the top catch is located above the holder.
Levelling the machine The machine must stand perfectly level on all four feet to ensure safe and proper operation. Incorrect installation may increase electricity and water consumption and may cause the machine to move about. Screwing out and adjusting the feet The four adjustable screw feet are used to level the machine.
Building under a worktop , The machine lid must not be removed. This washing machine can be pushed under a worktop with its lid in place, providing the worktop is high enough. Washer-dryer stack A Miele tumble dryer can be stacked with the washing machine.
The Miele water protection system The Miele water protection system protects the washing machine from water damage. The system consists of three main components: 1) the inlet hose 2) the electronic unit and the washing machine housing 3) the drain hose 1) Inlet hose The inlet hose is tested to withstand pressure of more than 7,000 kPa.
Connection to the water supply The machine should be connected to a mains water supply in accordance with local and national safety regulations. The German authorities do not require it to have a non-return valve as the washing machine has been designed to comply with DIN regulations.
Connection to the drainage system The machine drains via a drain pump with a delivery head of 1 metre*. The drain hose must not be kinked as this restricts drainage. The swivel elbow at the end of the hose can be turned in either direction, or can be detached if required, with a sharp twist and pull.
Electrical connection U.K. All electrical work should be carried out by a suitably qualified and competent person, in strict accordance with current national and local safety regulations (BS 7671 in the UK). Ensure power is not supplied to the appliance until after installation work has been carried out.
Consumption data 63 Load Consumption data Energy Water Duration in kWh in litres Cottons 90°C 7.0 kg 2.20 52 2 h 29 min 60°C 7.0 kg 1.33 52 1 h 59 min 60°C 3.5 kg 1.00 45 1 h 59 min Eco 60 * 7.0 kg 0.82 52 2 h 59 min Eco 60 * 3.5 kg 0.82 45 2 h 59 min 40°C 7.
Height 850 mm Width 595 mm Depth 656 mm Depth with door open 1092 mm Height for building under 850 mm Width for building under 600 mm Weight 99 kg Capacity 7 kg dry laundry Voltage See data plate Conn.
To access programmable functions Before you begin, first ensure that: – The washing machine is switched on. – The machine door is closed properly. ^ Press the Delay start ( V ) and Spin speed ( W ) buttons at the same time until: Language ! ... appears in the display.
Total usage This gives the sum total of all energy and water consumption. Energy This gives the sum total of all energy consumption. Water This gives the sum total of all water consumption. Reset function This resets the total consumption data figure back to zero.
Code A code can be used to lock the electronics on the washing machine to prevent it being used without your knowledge. When the code has been activated, you have to enter a code after switching the washing machine on. Otherwise the washing machine cannot be operated.
Temperature unit You can chose for the temperature to be displayed in °C/Celsius or °F/Fahrenheit . The machine is delivered with °C/Celsius as the default setting. Buzzer When the buzzer function has been activated, an audible tone sounds at the end of a programme or when Rinse hold is reached.
Standby display To save energy, the display goes out and the indicator light for the Start/ Stop button will start flashing slowly. The display will always go out, – if a programme is not selected within 10 minutes of the machine being switched on. – 10 minutes after the end of a programme.
Miele washing machines offer perfect care for your laundry and feature a wide range of special programmes designed to suit the fabric being washed. Miele have also developed a range of specialist CareCollection detergents and conditioning products to offer you a complete package for cleaning and caring for your laundry.
"UltraWhite" detergent This multi-purpose powder detergent has excellent stain removal properties and is suitable for white and light coloured laundry as well as heavily soiled coloured items. "UltraColor" detergent for coloured garments This liquid detergent is particularly suitable for cleaning coloured and dark garments.
Alteration rights reserved/1412/W 1945 M.-Nr. 09 345 280 / 00.
An important point after buying a device Miele W 1945 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Miele W 1945 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Miele W 1945 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Miele W 1945 you will learn all the available features of the product, as well as information on its operation. The information that you get Miele W 1945 will certainly help you make a decision on the purchase.
If you already are a holder of Miele W 1945, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Miele W 1945.
However, one of the most important roles played by the user manual is to help in solving problems with Miele W 1945. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Miele W 1945 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
