Instruction/ maintenance manual of the product KM2355 G Miele
Go to page of 20
Installation Instructions IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information. To prevent accidents and appliance damage read these instructions before installation or use.
Installation The minimum distances given in these Installation instructions are to combustible surfaces, and must be observed to ensure safe operation. Failure to do so increases the risk of fire. The cabinetry and venting hood should be installed first to prevent damage to the cooktop.
Safety distances above the appliance The minimum safety distance given by the hood manufacturer must be maintained between the cooktop and the hood above it. See the installation instructions of the hood for these safety measurements. If the hood manufacturers instructions are not available or if flammable objects are installed over the cooktop (e.
Safety distances When installing a gas cooktop, there may be cupboard or room walls of any size on the rear side and on one side (right or left) (see illustrations). The following minimum safety distances must be maintained: a 2" (50 mm) minimum distance at the rear of the countertop cutout to the rear edge of the countertop.
a Appliance front b Installation height c Gas connection d Power supply box with connection cable ,L=4f t (1.2 m) e Stepped cut-out for granite or marble worktops Please take careful note of the detailed diagrams for the cut-out dimensions in granite and marble countertops.
Flush mounted gas cooktops are only suitable for installation in granite, marble, tiled or solid wood countertops. If installing into a countertop made from any other material, please check first with the countertop manufacturer that it is suitable for installing a flush mounted cooktop.
Granite and marble countertops a Countertop b Cooktop c Gap As the ceramic glass and the countertop cut-out have a certain dimensional tolerances, the size of gap c can vary. ^ Make the countertop cut-out as shown in "Installation dimensions".
Solid wood and tiled worktops a Countertop b Cooktop c Gap d Wooden frame 1/4" (7 mm) (to be provided on site) As the ceramic glass and the countertop cut-out have a certain dimensional tolerance, the size of gap c can vary. ^ Make the countertop cut-out as shown in "Building-in dimensions".
Secure the appliance as shown, using the fixing brackets supplied. 3/4" (20 mm) countertop 1 1/4" (30 mm) countertop 1 1/2" (40 mm) countertop After installation Check that all the burners are operating correctly. The flame must not go out on the lowest setting, or when the control is turned quickly from a high to a low setting.
This appliance must be grounded according to local or national codes. All electrical work should be performed by a qualified electrician in accordance with local codes and with the: - National Electrical Code ANSI / NFPA No. 70 for the USA or - Canadian Electrical Code Part I for Canada (CSA Standard C 22.
Wiring diagram , Caution: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.
Installation and service must be performed by a qualified installer, service agency or gas supplier. In Massachusetts installation must be performed by a licensed plumber/gas fitter. This appliance must be installed with its own shut off valve and the included gas pressure regulator.
Gas pressure regulator A pressure regulator that is convertible from natural to LP gas (Propane) or vice versa is included with the appliance. The included regulator corresponds with the gas type of the appliance. Verify before installing. The adjusted pressure is: natural gas - 4" w.
The applinace should have been ordered for connection to either natural gas or LP gas (propane). If the appliance is not configured for the proper type of gas connection please contact your Miele Dealer.
Rated load at high setting Burner Type of gas KM 2355 BTU/hr kW Auxiliary burner Natural gas (NG) Liquid gas (LP) 3,900 3,000 1.14 0.88 Normal burner Natural gas (NG) Liquid gas (LP) 5,900 6,000 1.73 1.76 High-speed burner Natural gas (NG) Liquid gas (LP) 9,800 9,500 2.
Disposal of packing materials The cardboard box and packing materials are biodegradable and recyclable. Please recycle. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children. Danger of suffocation! Disposal of an old appliance Old appliances contain materials that can be recycled.
41.
42.
43.
M.-Nr. 09 596 090 / 00 e n-U S KM 2355.
An important point after buying a device Miele KM2355 G (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Miele KM2355 G yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Miele KM2355 G - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Miele KM2355 G you will learn all the available features of the product, as well as information on its operation. The information that you get Miele KM2355 G will certainly help you make a decision on the purchase.
If you already are a holder of Miele KM2355 G, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Miele KM2355 G.
However, one of the most important roles played by the user manual is to help in solving problems with Miele KM2355 G. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Miele KM2355 G along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
